iON Action cam Air Pro Plus IO19007 Owner's manual

Page is loading ...

1. Getting to know your WiFi PODZ and

BatterBooster



ion

WiFi PODZ provides the wireless capability to your ion cameras.



As long as you attach the PODZ to the camera and turn it on, your can access and

transfer your camera les through your PC, mobile phone or tablet.



WiFi PODZ

also turns your mobile device to be a wireless viewnder and you can preview

the camera view from your mobile device.



The battery booster works as an external battery which allows you to recharge your

camera from empty to full at about 1.5 hrs

WiFi PODZ & Battery Booster Kit

Quick Start Guide

EN

2. Getting to Know Your Package

1 WiFi PODZ

Provide the wireless capability to your ion

cameras

2 Battery Booster and Cable

Allow to fully charge your camera from

empty via the USB cable during your travel

3. Getting Started

Please connect your Air Pro with PC or Mac to update rmware in order to

activate the WiFi function. For details of rmware update, please refer to

section 3.1 of your camera quick start guide

3.1 Install your WiFi PODZ

TM

1. Remove the PODZ and put your WiFi PODZ to the camera PODZ socket

2. Seal the camera by rotating the back cover clockwise until two dots are aligned.

Slide the latch to lock the PODZ

3. Press and hold

button to turn on your camera

4. Press the WiFi power button on the WiFi PODZ to turn on

your WiFi. The blue LED lights up to indicate the WiFi is

warming up. It will take around 15-20 seconds for the WiFi

to warm up and become connectable. The LED will ash

when the Wi-Fi function is active or connected.

5. Press the WiFi power button to turn off the WiFi anytime.

Note:

1. WiFi will drain your camera battery more rapidly when activated. Turn the WiFi

off if you are not using it to change settings or upload content.

2. Failure to properly seal your camera can result in leaks that damage or destroy

your camera. Your warranty does not cover water damage resulting from user

damage.

3. The rubber seal on the PODZ forms the waterproof barrier to protect the

camera in wet and underwater conditions. You must keep this seal clean as a

single strain of hair or grain of sand can cause a leak into the product.

4. After every use in salt water, you will need to rinse the outside of the product

and the seal with non-salt water and dry. Not doing this can cause corrosion in

the product or failure in the seal, in turn, damaging the product.

3.2 Connect The Camera to Your Computer

1. Turn on your WiFi PODZ.

2. Go to network setting of your PC and choose WiFi setting. Search the network,

nd and click “WIFIPODZ”

3. Enter password “123456789” and you can connect to your camera.

4. Open your Internet browser and input “192.168.1.2” or “wi.podz”. You can

view the les stored in your camera

3.3 Connect The Camera to Your Smart Device (Browser)

1. Turn on your WiFi PODZ.

2. Go to network setting of your mobile device and choose WiFi setting. Search

the network, nd and click “WIFIPODZ”

3. Enter password “123456789” and you can connect to your camera.

4. Open your Internet browser and input “192.168.1.2” or “wi.podz”. You can

view the photos and videos stored in your camera.

3.4 Connect The Camera to Your Smart Device (App)

1. Search iontheaction app at the App store.

2. Download and install the app to your smart device

3. Turn on your WiFi PODZ.

4. Go to network setting of your PC and choose WiFi setting. Search the network,

nd and click “WIFIPODZ”

5. Enter password “123456789” and you can connect to your camera.

6. Open your app.

7. You can refer to app page for the detailed operation description.

Notes: As long as your camera starts video recording, the live streaming and le

play back and transfer function will be temporarily disabled. You can resume the

functions when your camera in standby status.

3.5 Charge your camera by the battery booster

1. Charge up the battery booster by the USB cable or adapter (not included). You

can press the button at the battery booster to show you the power status

2. Remove the PODZ

from your camera

3. Connect the battery booster to your camera thru the USB cable and it will start

charging up your camera automatically.

4. It takes around 1.5 hrs to fully charge up your camera from empty.

4. Trademark Information

® The ion logo is a registered trademark of World Wide Licenses Limited.

CamLOCK, PODZ, Shoot/Share and AIR PRO CONNECT and their respective logos are

trademarks or registered trademarks of World Wide Licenses Limited in the United States and

IMPORTANT

• Keep the lens clean. Dirt and ngerprints will affect the quality of the picture.

• Close the PODZ properly for best water sealing. Do not open it under water.

• Rinse the camera with clean water after used and keep it dry for storage.

• You can refer to the detail operation instruction at the user manual

WARNING: THE TRADEMARK INFORMATION

® The ion logo is a registered trademark of World Wide Licenses Limited.

• CamLOCK, PODZ, Shoot/Share and AIR PRO and their respective logos are

trademarks or registered trademarks of World Wide Licenses Limited in the United

FCC ID: NW71006

IMPORTANT REGULATORY INFORMATION

This device complies with Part 15 of the FCC Rules: Operation is subject to the

following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference that is received, including any

interference that may cause undesired ope

WARNING:

Changes or modications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However,there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For EU only

Questions?

Need Some Help?

This manual should help you

understand

your new product.

If you still have questions,

visit our website:

www.iontheaction.com

Like Us:

www.facebook.com/iontheaction

Tweet Us:

www.twitter.com/iontheaction

Page is loading ...

IMPORTANT

• Keep the lens clean. Dirt and ngerprints will affect the quality of the picture.

• Close the PODZ properly for best water sealing. Do not open it under water.

• Rinse the camera with clean water after used and keep it dry for storage.

• You can refer to the detail operation instruction at the user manual

WARNING: THE TRADEMARK INFORMATION

® The ion logo is a registered trademark of World Wide Licenses Limited.

• CamLOCK, PODZ, Shoot/Share and AIR PRO and their respective logos are trademarks

or registered trademarks of World Wide Licenses Limited in the United States and other

4. In ca. 1,5 Stunden wird ihre Kamera, falls die Batterie voll entladen war, wieder

voll aufgeladen sein.

4. TRADEMARK INFORMATION

® The ion logo is a registered trademark of World Wide Licenses Limited.

CamLOCK, PODZ, Shoot/Share and AIR PRO CONNECT and their respective logos are

trademarks or registered trademarks of World Wide Licenses Limited in the United States and

FCC ID: NW71006

IMPORTANT REGULATORY INFORMATION

This device complies with Part 15 of the FCC Rules: Operation is subject to the

following two conditions:

1. This device may not cause harmful interference and

2. This device must accept any interference that is received, including any

interference that may cause undesired ope

WARNING:

Changes or modications to this unit not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Changes or modications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However,there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Fragen?

Sie benötigen Hilfe?

Das Betriebshandbuch

soll Ihnen helfen ihr News

product kennenzulernen.

Haben Sie noch weitere Fragen,

rufen Sie unsere

oder besuchen Sie unsere

Homepage: www.iontheaction.com

Like Us:

www.facebook.com/iontheaction

Tweet Us:

www.twitter.com/iontheaction

For EU only

Page is loading ...

Des questions ?

Besoin d’aide ?

Ce guide vous aidera à

comprendre votre nouveau produit

Si vous avez d’autres

questions,

visiter notre site web : www.

iontheaction.com

www.facebook.com/iontheaction

Twittez nous :

www.twitter.com/iontheaction

Pour UE uniquement

Page is loading ...

Domande?

Bisogno d’aiuto?

Questo manuale ti aiuterà

a comprendere il tuo nuovo

prodotto.

In caso di ulteriori domande,

visita il nostro sito Internet:

www.iontheaction.com

Seguici su Facebook:

www.facebook.com/

iontheaction

Seguici su Twitter:

www.twitter.com/iontheaction

Solo per UE

Page is loading ...

¿Preguntas?

¿Necesitas ayuda?

Este manual debería

ayudarte a entender tu

nuevo producto.

Si todavía tienes dudas,

visita nuestra web:

www.iontheaction.es

Like Us:

www.facebook.com/iontheaction

Tweet Us:

www.twitter.com/iontheaction

For EU only

Page is loading ...

FCC Statement

Caution Statement

“Modications not approved by the party responsible for compliance could void the user’s

authority to operate the equipment.”

Instruction Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/ TV technician for help.

WARNING: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THE DEVICE. ANY

SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

Questions?

Need Some Help?

This manual should help you

understand

your new product.

If you still have questions,

visit our website:

www.iontheaction.com

Like Us:

www.facebook.com/iontheaction

Tweet Us:

www.twitter.com/iontheaction

For EU only

Page is loading ...

3

.

打开你的

WiFi PODZ

4.

进入你的个人计算机网络设置，选择

WiFi

设置。搜索网络，找到并点

击“

WIFIPODZ”

5

.

键入口令

“

123456789

”，

你就可以连接至照相机。

6

.

打开你的

app

应用程序

7

.

你可以参考

app

应用页面详细操作描述

注意：一旦你的相机开始录像 , 直播功能、文件回放功能和传递功能将

被暂时禁用。在待机状态时，你就可以恢复这些功能。

3.5

通过备用电池为你的相机充电

1

.

通过

USB

线或充电器（附件不包含）为备用电池充电。你可以按备用

电池上的按钮来显示电源状态。

2

.

从你的相机中移除

PODZ.

3

.

通过

USB

线连接备用电池至你的相机

，

它就会开始自动为你的相机

充电。

4

.

将你的相机充满电大约要花一个半小时。

4. Trademark Information

® The ion logo is a registered trademark of World Wide Licenses Limited.

CamLOCK, PODZ, Shoot/Share and AIR PRO CONNECT and their respective logos are

trademarks or registered trademarks of World Wide Licenses Limited in the United States and

.

FCC Statement

Caution Statement

“Modications not approved by the party responsible for compliance could void the user’s

authority to operate the equipment.”

Instruction Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/ TV technician for help.

WARNING: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV

INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THE DEVICE. ANY

SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE

EQUIPMENT.

Questions?

Need Some Help?

This manual should help you

understand

your new product.

If you still have questions,

visit our website:

www.iontheaction.com

Like Us:

www.facebook.com/iontheaction

Tweet Us:

www.twitter.com/iontheaction

For EU only

Page is loading ...

iON Action cam Air Pro Plus IO19007 Owner's manual

This manual is also suitable for

iON Action cam Air Pro Plus IO19007 Owner's manual

in other languages

Related papers

Other documents