B&C Technologies HE-110 Operating instructions

Category
Washing machines
Type
Operating instructions

This manual is also suitable for

Washer-Extractor
HE Series Installation and Operation Manual
November 4, 2014
Revision 2.91
Contents
1 Important Instructions 2
1.1 BeforeAttemptingRepairs.................................. 2
1.2 PartsOrderingInformation ................................. 3
1.2.1 NameplateLocation ................................. 3
1.3 KeySymbols.......................................... 3
1.4 SafetyInformation ...................................... 5
1.5 Installation and Operational Safety Instructions . . . . . . . . . . . . . . . . . . . . . 5
2 Introduction 6
2.1 CustomerService ....................................... 6
2.2 ReplacementParts ...................................... 7
2.3 TheoryofOperation ..................................... 7
3 General Specifications 9
4 Installation 11
4.1 ReceivingInspection ..................................... 11
4.2 SafetyChecklist ........................................ 11
4.2.1 OperatorSafety.................................... 12
4.2.2 Safe Operation Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.3 Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.4 MachineLocation................................... 14
4.2.5 Input and Output Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.2.6 InverterDrive..................................... 15
i
4.2.7 MachineMisuse.................................... 15
4.3 DimensionalClearances ................................... 16
4.4 MachineFoundation ..................................... 17
4.4.1 Machine Foundation Construction . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.5 MountingBoltInstallation.................................. 20
4.5.1 HE-35 Mounting Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4.5.2 HE-45 Mounting Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4.5.3 HE-65 Mounting Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4.5.4 HE-85 Mounting Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.5.5 HE-110 Mounting Bolt Installation . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.6 DrainInstallation ....................................... 25
4.7 ElectricalInstallation ..................................... 26
4.8 WaterConnection....................................... 28
4.9 SteamConnection....................................... 28
4.10ExternalChemicalSupplies ................................. 29
4.10.1 ChemicalConnection ................................ 30
4.10.2 Chemical Signal Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4.11ControlFunctionTest..................................... 32
5 Operation 34
5.1 DoorLockOperation..................................... 34
5.1.1 Opening and Closing the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.1.2 PeriodicMaintenance ................................ 34
5.2 MachineLoading ....................................... 35
5.3 WashProgramExecution................................... 36
5.3.1 CycleSelection .................................... 36
5.3.2 CycleExecution.................................... 36
6 Maintenance 38
6.1 Daily .............................................. 38
6.1.1 BeginningofDay................................... 38
ii
6.1.2 EndofDay ...................................... 39
6.2 Weekly ............................................. 39
6.3 Monthly ............................................ 39
6.4 Quarterly............................................ 41
6.5 CareofStainlessSteel..................................... 42
7 Service & Parts 44
7.1 Service ............................................. 44
7.2 Parts .............................................. 44
8 Decommisioning 45
iii
Figure 1: HE Product Family
1
Chapter 1
Important Instructions
1.1 Before Attempting Repairs
Moving parts can cause serious injury or death. Before attempting repairs, follow proper shut-
down procedures and remove power before commencement of service.
Safety is of primary concern with any maintenance or repair operation. If you are in any way
unsure of how to proceed with a repair or adjustment, consult this manual, a qualified mainte-
nance technician, your local distributor, or the B&C Technologies Technical Service Department at
850-249-2222.
Only trained and experienced personnel should attempt maintenance or repair work on this equip-
ment. Follow all safety procedures including lock-out/tag-out procedures carefully. Ensure that
any loose fitting clothing or jewelry is tucked in or not worn to avoid being pulled into the ma-
chine. Remember, the machine has no brain - you must use your own.
Before attempting repairs, follow proper shutdown procedures and remove power before com-
mencement of service.
Never attempt to clean or service any area of the machine without removing power at the main
disconnect.
Read, follow, and obey these safety rules! The B&C Technologies Technical Service Department
2
is available to answer any questions you may have about the operation and servicing of your
machine. Please call with any questions or concerns about the operation of your machine.
1.2 Parts Ordering Information
If you require literature or spare parts, please contact your local distributor. If a local distributor
is unavailable, you may contact B&C Technologies directly at (850) 249-2222 for the name of your
nearest parts dealer.
For technical assistance in the United States, contact B&C Technologies:
(850) 249-2222 Phone
(850) 249-2226 FAX
www.bandctech.com
1.2.1 Nameplate Location
When contacting B&C Technologies about your equipment, please make note of the model and
serial number, located on the nameplate as shown in figure 1.1.
Figure 1.1: Serial Decal
1.3 Key Symbols
Anyone operating or servicing this machine must follow the safety rules in this manual. Partic-
ular attention must be paid to the DANGER, WARNING, and CAUTION blocks which appear
throughout the manual and shown in figures 1.2 on page 4 and 1.3 on page 4.
3
Figure 1.2: Key Symbols
Figure 1.3: Key Symbols
4
1.4 Safety Information
Installation Notice: For personal safety and for proper operation, the machine must be grounded
in accordance with state and local codes and in the USA in accordance with the National Electric
Code, article 250-96. Elsewhere, the equipment should be grounded in accordance with ANSI/NFPA
70, or the Canadian Electrical Code, CSA C22.1. The ground connection must be to a proven earth
ground, not to conduit or water pipes.
1.5 Installation and Operational Safety Instructions
1. Read all instructions prior to operating this equipment.
2. Ensure that the equipment is properly grounded before applying power and operation com-
mences.
3. Do not allow children to play in or around or operate this equipment.
4. Check the operation of all safety interlocks at the start of every shift. If the interlocks do not
stop the equipment immediately, the machine must be removed from service. Notify your
immediate supervisor, and do not operate the machine.
5. Never attempt to service the machine while it is running. Never reach over, under, around, or
behind any safety device, or into any area near moving parts or hot surfaces without shutting
off power and allowing the machine to adequately cool.
6. Read, understand, and follow all safety instructions. Do not come close to moving parts and
hot surfaces. Do not wear loose clothing, jewelry, neckties, or any other garment that could
be come caught in the machine while operating or near the machine.
7. Only a qualified technician should attempt to service or repair the machine.
8. Do not install the machine in an area where it could be exposed to water or weather.
9. Do not alter or tamper with the control system.
10. Keep the interior and exterior of the machine clean of lint, dirt, dust and debris.
11. Always disconnect the electrical service from the machine before performing service.
12. This machine must be installed according to the installation instructions. All utility connec-
tions must comply with state and local codes and must be made by a licensed installer where
required.
5
Chapter 2
Introduction
The HE line is the professional fixed mount washer-extractor series of machines from B&C Tech-
nologies. It is an open pocket washer-extractor with a large door opening for easy and quick
loading and unloading. It has been developed for the on premise market, and is suitable for com-
mercial laundries, hotel and other places where laundry might be processed.
The design allows for top performance at lowest possible operation cost and investment. The
flexible electronic control center ensures that maximum productivity is obtained.
The HE series utilizes high quality material, such as 304 (18/8) stainless steel in vital parts in
contact with the wash solution. It has a stainless steel and painted cabinet for long life with easily
removable panels.
The key advantages of this series are the simplicity of the microprocessor and the electronic AC
drive system, which utilizes only one motor. The system allows for washing, extraction and me-
chanical action to suit any textile fiber used today and tomorrow. The high speed final extraction
saves time and energy in the finishing operation.
A multi compartment supply dispenser for powder and liquid detergents is standard and the
machine is designed to accept the connection of 4 external chemical lines and pumps.
2.1 Customer Service
For technical assistance:
In the United States
Phone: (850)-249-2222
FAX: (850) 249-2226
Web: www.bandctech.com
6
2.2 Replacement Parts
In the event that literature or replacement parts are required, contact the local distributor of the
equipment, or contact B&C Technologies at the above phone numbers/internet addresses.
2.3 Theory of Operation
The HE models use a single-speed motor to drive the cylinder via V-belts in all speeds. The cylin-
der is supported by two spherical roller bearings located in a bearing housing made of cast iron.
The motor is controlled by the computer control located in the front and the AC inverter drive
located in the rear panel. Wash and extract speeds are fixed. Any temperature between 70F to
200F (20-95C) can be programmed. The water level is fixed, with a low level and a high level pro-
vided (medium level is included with the A computer). The computers will automatically provide
safety levels for steam injections and door operations. The AC Drive performs balance detection
to ensure that excessively out of balance loads do not damage the machine or floor. A catastrophic
failure sensor is also provided to stop the machine in the event of a severe malfunction.
Water entry into the machine is through an air gap vacuum breaker utilizing electro-magnetic wa-
ter valves controlled by the computer. By utilizing the air gap vacuum breaker, backflow into the
water supply is impossible. The computer also controls the drain, supply dispenser, any external
liquid supplies, steam injection and any other vital functions of the wash program.
The steam, if installed, is injected in the bottom of the shell via a steam injector. The steam is
controlled by a steam valve that is programmed by the micro computer.
The cylinder is perforated, allowing water to pass through and drain from within during drain
and extract steps. Lifting ribs inside the cylinder lift the load from the wash solution and allow
the load to tumble and falling back into the solution when the load reaches the approximate 10-11
o’clock or 1-2 o’clock positions. This mechanical action removes soil from the fabric. Furthermore,
the lifters are perforated on the top so that water can cascade over the goods and wet them quickly.
This reduces water consumption as water is picked up at the cylinders lowest point and lifted and
splashed over the goods at the highest point as the cylinder rotates.
A stainless steel door is provided for loading and unloading. A door lock system prevents op-
eration of the machine when the door is open. The door is locked during operation utilizing an
electronic solenoid and a latch for safety reasons. The door lock is provided with magnetic sensor
to indicate that the door is closed and locked and allows for start of the machine when the door is
closed and locked.
The AC drive, circuit overload protectors, input power supply connections, external supply con-
nections, and control transformer are behind a cover on the rear of the machine.
The supply dispenser is mounted on the front of the machine and is accessed by opening the cover
door. Supplies, both liquid and powder, may be added by pulling the dispenser cups out and
placing the appropriate supply in each. Supplies are flushed into the machine at the proper time
in the cycle, controlled by the micro computer.
7
Holes are provided at the rear of the machine for connection to an external, central liquid supply
unit. Electrical connections are provided for the liquid supply unit on a terminal strip inside the
rear control module. Refer to page 32 for connection details.
8
Chapter 3
General Specifications
Figure 3.1: HE Series General Specifications
9
Figure 3.2: HE Series Basic Dimensions
10
Chapter 4
Installation
4.1 Receiving Inspection
Upon receipt of the equipment, visually inspect for shipping damage and note any damage with
the carrier before signing the shipping receipt, or advise the carrier of the damage as soon as it is
noted.
If damage is discovered, a written claim must be filed with the carrier as soon as possible.
Note: Warranty is VOID unless the equipment is installed according to instructions. The installa-
tion must comply with the minimum requirements listed in this manual. All national, state and
local codes must be followed including but not limited to gas, electrical, plumbing and HVAC.
Due to various requirements, statutory codes should be well understood before installation com-
mences.
Important: The machine should be transported and handled in an upright position.
4.2 Safety Checklist
Before Initial start up of a B&C washer extractor perform the following safety check:
1. Make sure all electrical and plumbing connections have been made in accordance with ap-
plicable codes and regulations.
2. Make sure the machine is grounded electrically.
3. Make sure the machine has flexible water fill and drain connections of the correct size, length
and type, with no kinks, and that they are securely attached and/or clamped.
Before machine is placed in operation, the door safety interlock must be checked for proper oper-
ation as follows:
11
Before servicing any equipment, make certain it is disconnected from the electrical
power source. Never allow operation of the machine when any safety device is
malfunctioning. Never bypass safety devices.
Never insert hands or objects into basket until it has completely stopped. Doing
so could result in serious injury.
1. When the washer is energized electrically and in operation, the loading door must be locked
in the closed position. Verify this by attempting to open the loading door when the machine
is operating. If necessary, check the door safety interlock and sensors for proper operation.
Consult the service manual, or call a qualified service technician if necessary.
2. When the washers loading door is open, it should not be possible to start the machine. Verify
this by attempting to start the washer with the door open. Also, close the door without
locking it and verify that it is not possible to start the machine with the door not locked. If
necessary, check the door lock sensors for proper operation,. Consult the service manual, or
call a qualified service technician. If additional information is required, contact your local
distributor or call the manufacturer of the machine.
To provide personal safety and keep the machine in proper working order, follow all main-
tenance and safety procedures presented in this manual. If questions regarding safety arise.
Contact the factory immediately.
Use factory authorized spare parts to avoid safety hazards.
4.2.1 Operator Safety
To ensure the safety of machine operators the following maintenance checks must be performed
daily.
1. Prior to operating the machine, verify that all warning signs are present and legible. Missing
or illegible signs must be replaced immediately. Make certain that spares are available.
2. Check door interlock before starting operation of the machine, see safety check list.
3. Do not attempt to operate the machine if any of the following conditions are present:
(a) The door does not remain securely locked during the entire cycle.
(b) Excessively high water level is evident.
(c) Machine is not connected to a properly grounded circuit.
Do not bypass any safety devices in the machine.
12
Never operate the machine with a bypassed or disconnected out-of-balance
switch. Operating the machine with severe out-of-balance loads could result
in personal injury and serious equipment damage.
Do not place volatile or flammable fluids in any machine. Do not clean the ma-
chine with volatile or flammable fluids such as acetone, lacquer thinners, enamel
reducers, carbon tetrachloride, gasoline, benzene, naphtha, etc. Doing so could
result in serious personal injury and/or damage to the machine.
4.2.2 Safe Operation Environment
Safe operation requires an appropriate operating environment for both the operator and the ma-
chine. If questions regarding safety arise, contact the factory.
4.2.3 Environmental Conditions
1. Ambient temperature. Water in the machine will freeze at temperatures of 32F (0C) or below.
Temperatures above 120 F (50C) will result in more frequent motor overheating and, in some
cases, malfunction or premature damage to solid state devices that are used in the machines.
Special cooling devices may be necessary.
2. Humidity. Relative humidity above 90% may cause the machines electronics or motors to
malfunction or may trip the ground fault interrupter. Corrosion problems may occur on
some metal components. If the relative humidity is below 30% belts and rubber hoses may
eventually develop dry rot. This condition can result in hose leaks, which may cause hazards
external to the machine in conjunction with adjacent electrical equipment.
3. Ventilation. The need for make-up air openings for such laundry room accessories as dry-
ers , ironers, water heaters, etc. must be evaluated periodically. Louvers, screens, or other
separating devices may reduce the available air opening significantly.
4. Radio Frequency Emissions. A filter is available for machines in installations where floor
space is shared with equipment sensitive to radio frequency emissions. All machines that are
shipped to CE countries are equipped with this filter and comply with the EMI regulations.
5. Elevation. If the machine is to be operated at elevations over 3280 feet (1000 meters) above sea
level, pay special attention to water levels and electronic settings ( particularly temperature)
or desired result may not be achieved.
6. Chemicals. Keep stainless steel surfaces free of chemical residues to avoid corrosion.
7. Water damage. Do not spray the machine with water. Short circuiting and serious damage
may result. Repair immediately all seepage due to faulty gaskets, etc.
13
Replace all panels that are removed to perform service and maintenance pro-
cedures. Do not operate the machine with missing guards or with broken or
missing parts. Do not bypass any safety devices.
4.2.4 Machine Location
1. Foundation. The concrete floor must be of sufficient strength and thickness to handle the
floor loads generated by the machine at high extract speeds.
2. Service/ Maintenance Space. Provide sufficient space to allow comfortable performance of
service procedures and routine maintenance. This is especially important in connection with
machines equipped with AC inverter drives. Consult installation instructions for specific
details.
4.2.5 Input and Output Services
1. Water pressure. Best performance will be realized if water is provided at a pressure of 30-85
psi (2.0-5.7 bar). Although the machine will function properly at lower pressure, increased
fill time will occur. Water pressure higher than 120 psi (8.0 bar) may result in damage to
machine plumbing. components failure(s) and personal injuries.
2. Optional Steam heating pressure. Best performance will be realized if steam pressure is
provided at a pressure of 30-80 psi (2.0-5.4 bar). Steam pressure higher than 125 psi (8.5 bar)
may result in damage to steam components and may cause personal injuries. For machines
equipped with optional steam heat, install piping in accordance with approved commercial
steam practices. Failure to install a steam filter may void the warranty.
3. Drainage System. Provide drain lines or troughs large enough to accommodate the total
quantity of water that could be dumped if all machines on the site drained at the same time
from the highest attainable level. If drain troughs are used, they should be covered to support
light foot traffic.
4. Power. For personal safety and for proper operation, the machine must be grounded in accor-
dance with state and local codes. The ground connection must be to a proven earth ground,
not to conduits or water pipes. An easy-access disconnect switch should be provided.
Ensure that a ground wire from a proven earth ground is connected to the ground lug in the elec-
trical junction box on this machine. Without proper grounding personal injury from electrical
shock could occur and machine malfunctions may be evident. Computer-controlled machines
must have a proper ground to prevent computer malfunctions.
14
Always disconnect power and water supplies before a service technician performs
any service procedure. Where applicable, steam and/or compressed air supplies
should also be disconnected before service is performed.
4.2.6 Inverter Drive
Machines equipped with AC drives require special attention with regard to the operating envi-
ronment.
1. An especially dusty or linty environment will require more frequent cleaning of the AC drive
cooling fan filter and of the AC drive itself.
2. Power line fluctuations from sources such as an uninterruptible power supplies (UPS) can
adversely affect machines equipped with the AC drive. Proper suppression devices should
be utilized on the incoming power to the machine to avoid problems.
3. A clean power supply free from voltage spikes and surges is absolutely essential for ma-
chines equipped with the AC drive. Nonlinear inconsistencies (peaks and valleys) in the
power can cause the AC drive to generate nuisance errors. If voltage is above 230V for
200 V installations or above 460V for 400V installations, a buck/boost transformer is recom-
mended. If voltage is above 240V or 480V, a buck/boost transformer is required unless the
factory advises differently.
4. Sufficient space to perform service procedures and routine preventive maintenance is espe-
cially important for machines equipped with AC drives.
4.2.7 Machine Misuse
Even though this machine is an atmospheric vessel, never use it for any purpose other than
washing fabrics.
1. Never wash petroleum-soaked rags in the machine. This could result in an explosion.
2. Never wash machine parts or automotive parts in the machine. This could result in serious
damage to the wash cylinder.
3. Never stone wash in the machine. It could wear the wash cylinder and serious damage might
occur to the machine.
4. Never use the machine for dyeing nor with harsh chemicals that can cause corrosion and
other health hazards.
5. Never allow children to play on or around this machine. Death or serious injury can result
if children become trapped in the machine. Do not leave children unattended while the
machine door is open. These cautions apply to animals as well.
15
4.3 Dimensional Clearances
When installing the washer-extractor, it is important to allow adequate clearance on all sides of the
machine. When multiple machines are installed, it is important to allow for the specified minimum
clearances between machines. The following table shows recommended minimum clearances for
the various freestanding models.
Note: The dimensions are approximate and subject to normal manufacturing tolerances. If
exact dimensions are required for construction purposes, request certified drawings from the
factory. We reserve the right to make changes at any time without notice.
Figure 4.1: Minimum Service Clearances
16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49

B&C Technologies HE-110 Operating instructions

Category
Washing machines
Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI