Bonnet B-CAP.IN5 Installation Instructions Manual

Bonnet
Brand
Bonnet
Model
B-CAP.IN5
Type
Installation Instructions Manual
READY-TO-INSTALL
5 KW
INDUCTION
& WOK
MANUFACTURER’S INSTRUCTIONS
Part A: Technical data
Part B: Installation instructions
- WARNING -
•
Installation and repairs must be carried out by personnel approved by the manufacturer and in
accordance with current regulations and standards.
•
If any modifications are made the manufacturer can accept no responsibility whatsoever.
•
These appliances must be used in a well-ventilated area.
•
Read the notice carefully before installation.
•
The unit must be kept on its base for handling until it is in its final location.
N° 390526NI
9
Page 1 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
CONTENTS
5 KW INDUCTION
& WOK
A) TECHNICAL DATA ………………..…..................................................…. 2
B) FITTER’S INSTRUCTIONS
1.
Location of the identification plate …….........................................…...
4
2. Installation: General features …………….……..……………………..…. 5
2.1
General requirements ..………..……….……...….……...…...…….. 5
2.2
Handling ……..…….....……………………………………………..… 5
2.3
Unpacking …..…...…………..………………………..…………….... 5
2.4
Installation ….……….……...…………………………………………. 5
3. Installation: Connections ….………………………………………...….…. 6
3.1
Electrical connections ….……………..…...……...………..…….…. 6
Page 2 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
A: TECHNICAL CHARACTERISTICS
INDEPENDENT COOKING RANGE, ready-to-install 5 kW induction
P072138
ELECTRICAL outlet
MODEL
B-CAP.IN5
DIMENSION
Width 400
Depth 500
Height 122.5
PACKAGING (mm)
Width 450
Depth 550
Height 150
WEIGHT (KG)
15
ELECTRICITY (Three-phase 400V+T)
Power (kW) 400V 3a.c. 5
Max. intensity (A) 400V 3a.c. 7.3
AIR INLET
Environment
Ambient temperature ≤ 32°C
ELECTRICAL CONNECTION
Connection through 3-pole + earth socket (not supplied) compliant to the EN 60.083 standard
The equipment is fitted with a 1.5 m long supply cable.
Non contractual document Edition 11/2005 – 3BE0322
Page 3 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
INDEPENDENT COOKING RANGE, read-to-install 5 kW induction WOK
P072139
ELECTRICAL outlet
MODEL
B-CAP.WI5
DIMENSION
Width 400
Depth 500
Height 176.5
PACKAGING (mm)
Width 450
Depth 550
Height 200
WEIGHT (KG)
17
ELECTRICITY (Three-phase 400V+T)
Power (kW) 400V 3a.c. 5
Max. intensity (A) 400V 3a.c. 7.3
AIR INLET
Environment
Ambient temperature ≤ 32°C
ELECTRICAL CONNECTION
Connection through 3-pole + earth socket (not supplied) compliant with the EN 60.083 standard.
The equipment is fitted with a 1.5 m long supply cable
Non contractual document Edition 11/2005 – 3BE0323
Page 4 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
1. IDENTIFICATION PLATE
The identification plate is fixed under the equipment about the back part (see the diagrams below).
In any correspondence about your equipment please quote:
- The model number (Model.)
- The serial number (Fab.Nr.)
- The date (Date).
Identification plate
Location of the identification plate
Page 5 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
2. INSTALLATION: GENERAL FEATURES
TYPE AND POSITION OF CONNECTIONS
See "Technical Data" at the beginning of this instruction manual.
2.1 GENERAL REQUIREMENTS
The installation, modification or repair of the appliance must be carried out according to current
regulations by a specialised fitter.
These appliances are designed for professional use, they must be used by qualified personnel.
The appliances must be installed with sufficient ventilation to prevent the formation of excessive
concentrations of substances harmful for health in the premises in which they are installed.
These units are not designed to work in explosive atmospheres. Due to this, they must not be
installed in a zone relating to the ATEX provision.
The functioning of the appliance complies with the standards of electromagnetic perturbations in
force. Thus your equipment perfectly meets the statutory requirements. It is designed in order not to
hinder the functioning of other electrical equipment in so far as the latter also complies with the same
regulation.
Do not install your equipment under a shelf or close to flammable materials, such as curtains,
tentures, etc.
The equipment must be installed on a clean, horizontal, flat, stable and heat-resistant surface or
lined with such a material.
The air inlet under the appliance must not be obstructed (example: paper, cloth…).
Do not place any source of heat, steam or water projection close to the equipment.
After any shifting of the induction table, wait a few seconds before manipulating the keyboard.
The manufacturer certifies that the packaging conforms to the provision 94/62/CE of 20.12.94 and
requests that the fitter (and the user) observes the provision with regard to recycling or reuse of the
packaging materials.
2.2 HANDLING
Should the appliance need to be handled, it must be done in its original packaging and must not be
stacked under any circumstances.
When moving it and in absence of packaging, the appliance should be carried and not pulled.
Do not move the equipment when in use.
2.3 UNPACKING
Before installation, remove the strapping from the appliance. The individual parts are not bolted down.
Remove plastic film from the stainless steel parts before heating.
2.4 INSTALLATION
Remove the equipment from its packaging.
Pull and unwind completly the supply cable of the appliance.
Leave a distance of 50 mm from any vertical wall.
Page 6 390 526NI – 11/05
BONNET CIDELCEM GRANDE CUISINE
Siége social:
Rue des Frères Lumière - Z.I Mitry Compans
77292 MITRY MORY Cedex
3. INSTALLATION: CONNECTIONS
3.1 ELECTRICAL CONNECTION
The appliance is equipped with a 1.5 m long supply cable for connecting with a 3-pole + earth (not
supplied) connector which complies with the EN 60.083 standard.
Provide a suitable isolating device (with contact separation of at least 3mm) in accordance with current
regulations.
The installation must comply with current applicable national legislation (for France, standard NF
15.100).
The appliance must be connected to the earth.
The manufacturer cannot be held responsible if these instructions are not followed.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Bonnet B-CAP.IN5 Installation Instructions Manual

Bonnet
Brand
Bonnet
Model
B-CAP.IN5
Type
Installation Instructions Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents