American Standard TU662225.002 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

This manual is also suitable for

American Standard TU662225.002 is a commercial shower system kit designed for both residential and commercial use. It is equipped with a 2.5 GPM flow rate, ensuring a powerful and consistent shower experience. The kit includes a valve trim, wall supply, hand shower slide bar, and hose and hand shower, providing a complete showering solution. The valve trim features a single-handle lever design for easy temperature and flow control, while the hand shower slide bar allows for adjustable height and positioning.

American Standard TU662225.002 is a commercial shower system kit designed for both residential and commercial use. It is equipped with a 2.5 GPM flow rate, ensuring a powerful and consistent shower experience. The kit includes a valve trim, wall supply, hand shower slide bar, and hose and hand shower, providing a complete showering solution. The valve trim features a single-handle lever design for easy temperature and flow control, while the hand shower slide bar allows for adjustable height and positioning.

- 1 -
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
36"
48"
TO
BOTTOM OF SHOWER
1-5/8" TO 3-1/4"
12"
OPTIONAL
OPTIONAL
OPTIONAL TO FINISHED
FLOOR USUALLY
BETWEEN 48" TO 54"
1/2" SUPPLIES
PLUG TUB
OUTLET
6" DIA.
FINISHED WALL
8"
5-7/8"
33-3/8"
1-1/4"
1/2"
1/2" NPT
1660767
2-5/8"
1/2" NPSM
9-1/2"
35-3/8"
2-1/2"
3-3/8"
1660766
2-5/8"
1/2" NPSM
9-1/2"
UNIVERSAL INLETS / OUTLETS: 1/2" NOM
COPPER SWEAT OR 1/2" NPT
TOP OF TUB RIM
4"
4-3/8" REF.
1/2" COPPER
1" MIN.
Certied to comply with ANSI A112.18.1
M985027 (5/19)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2019
Thank you for selecting American Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
Installation must conform to all local building codes.
RECOMMENDED TOOLS & MATERIALS
ROUGHING-IN DIMENSIONS
COMMERCIAL SHOWER
SYSTEM KITS:
1.5 gpm & 2.5 gpm
INSTALLATION
INSTRUCTIONS
TU662.225
TU662.215
TU662.215
(1.5 GPM)
TU662.225
(2.5 GPM)
Electric Drill
Torch
6 mm (15/64")
Drill Bit
Pencil
Phillips Screwdriver Hammer
Adjustable Wrench
10'
Pipe Wrench Tubing Cutter
Tape Measure
Sealing Tape
- 2 -
2
INSTALL WALL SUPPLY
NOTE: REFER TO INSTALLATION INSTRUCTIONS (M968637)
SUPPLIED WITH WALL SUPPLY FOR COMPLETE
INSTALLATION AND REPAIR PART INFORMATION.
n Supply to WALL SUPPLY is 1/2" NPT. See rough-in above for
detailed information.
n Apply sealant or sealing tape to threads of 1/2" NPT supply nipple.
1
M985027 (5/19)
1/2" NPT
APPLY SEALANT
OR SEALING TAPE
INSTALL VALVE TRIM
NOTE: REFER TO INSTALLATION INSTRUCTIONS (M965937)
SUPPLIED WITH VALVE TRIM KIT FOR COMPLETE
INSTALLATION AND REPAIR PART INFORMATION.
n When nished tiling the wall, remove PLASTER GUARD.
UP
1-1/2" REF.
PLASTER GUARD
H
C
Off
- 3 -
M970487-YYY0A
LEVER HANDLE KIT
M970221-0070A
HANDLE SCREW KIT
M970410-0070A
CARTRIDGE
PURCHASE SEPARATELY
M970640-0070A
BACK-TO-BACK
CARTRIDGE
078016-YYY0A
ESCUTCHEON SCREWS
M962490-YYY0A
ESCUTCHEON AND SCREWS
M907050-YYY0A
ESCUTC HEON CAP SET
M909338-0070A
DECAL FOR THE
WD VERSION
H
C
OFF
H
C
Off
M970457-0070A
HANDLE ADAPTER KIT
M950231-YYY0A
DIVERTER SPOUT
(SLIP-ON)
3 4
INSTALL HAND SHOWER SLIDE BAR
CARE INSTRUCTIONS:
INSTALL HOSE AND HAND SHOWER
TEST SHOWER SYSTEM
NOTE: REFER TO INSTALLATION INSTRUCTIONS
(M968637) SUPPLIED WITH SHOWER SYSTEM
KIT FOR COMPLETE INSTALLATION AND
REPAIR PART INFORMATION.
n The height and location of the SLIDE BAR is optional.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
NOTE: REFER TO INSTALLATION INSTRUCTIONS
(M968637) SUPPLIED WITH SHOWER SYSTEM
KIT FOR COMPLETE INSTALLATION AND
REPAIR PART INFORMATION.
n Place the HAND SHOWER into the SLIDE BAR after all
hose connections are made. The installation of the
SHOWER SYSTEM KIT is now complete.
n Turn on water supplies and check all fuctions of of the
SHOWER SYSTEM KIT. Check for any leaks.
M985027 (5/19)
35-3/8"
(899 mm)
33-3/8"
(848 mm)
2-1/2"
(64 mm)
3-3/8"
(86 mm)
1660767
HAND SHOWER
1660766
HAND SHOWER
MODEL NUMBER
TU385500WD
RELIANT 3
PRESSURE BALANCING
BATH AND SHOWER
TRIM KIT
  • Page 1 1
  • Page 2 2
  • Page 3 3

American Standard TU662225.002 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide
This manual is also suitable for

American Standard TU662225.002 is a commercial shower system kit designed for both residential and commercial use. It is equipped with a 2.5 GPM flow rate, ensuring a powerful and consistent shower experience. The kit includes a valve trim, wall supply, hand shower slide bar, and hose and hand shower, providing a complete showering solution. The valve trim features a single-handle lever design for easy temperature and flow control, while the hand shower slide bar allows for adjustable height and positioning.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI