1.##Remove#all factory#screws#from#the
underside# of#the#front#fender#wheel#wells.
Save#the#factory#screws#for#flare#installation
.##
**Note:# #Depending#on#the#year,# make# and#model# of#your#
truck,#not#all# the#screws#pictured#on#the #left ma y# be#there .
**Note:# #If#your#vehicle# has#mudflaps,#after# market#
moldings,#ground#effe cts,#e tc. which#impede# ins tallation#or#
create#gaps #between# th e# flare#an d#truck#b ody,#those#must#
be#removed# as #well.
Includ ed(Comp o n en ts:
INSTALLATION:
**Consultation#with# a#profes s ional#installer# is#highly#recommended.# #Improper# installation#may# void#warranty.
**# Pleas e#test#fit#ALL#pieces #on#your#vehicle#before#painting#or#ins talling.
**# For#bes t#res ults ,#ins tall# in#warm# conditions#to#allow#for#better# 3M#tape#adhes ion.
**# Pre-exis ting# acces s ories #ins talled#on#the#vehicle# may# need#to#be# removed# if#they# impede# ins tallation#of#the#fender# flares # (i.e.#
mudflaps,#body/wheel# molding,#ground#e ffects,# emble ms,# etc.)
**# Consultation#with#a#profes s ional#painter/body# s hop#is #highly#recommended.# #
**# If#you#are# painting# the#fender# flares,# 2 #layers #of#flexible# 2K#Primer#is#recommended# before#applying# paint.## Pre-test(fitment(and(
drill(hole s ,(then(double(chec k(hole (alignme nt(BEFORE( painting.( (Monkey#Autosports WILL(NOT warranty# items# painted# without#
pre-application# of#2K#Primer#or#proper#pre -fitment#tes ting#procedure.
**# Clean# all#s urfaces #of#the#fender# flares#thoroughly#before# applying# primer# and#paint.##Clean# with# water# and#a#mild# detergent# or#
light# soapy#water.##Do#not#use#lacquer#thinner#or#any# ha r sh#solvent#ba sed#cleaners
Installation instructions for
Chevrolet and GMC Truck and SUV Factory/OE Style Fender Flares
(Excludes all Flareside/Stepside models)
1
Front#Right#
Flare#(FR)
Rear# Right#
Flare#(RR)
Rear# L eft#
Flare#(RL )
Front#L eft#
Flare#(FL )
Push-In# Retainer:#
30#pieces
Self-tapping#screws:
8#pieces
(For#Optional# installation)
*( Dr ive r ’s(Sid e (Fr o n t (P ict u r e d
3.#Wash#and#co mpletely# dr y# fender #fender#
flare#contact#areas#of#all#fenders.##Make#
sure#the#area#is#completely#clean#and#dry#
before#installation.#Make# sure#the#interior#
edge#of#the#fender#is#also#clean#and#cl ear#of#
any# obstructions# that#may#im pede#the#
installation#of# the#flares.#
4.#Remove#2”#of#the#r ed #backin g# of#each#
strip#of #double#sided#tape#and#bend#the#
excess#so#a#tab#is#exposed.##DO#NOT#
REMOVE#THE# ENTIRE#BACKING#TILL#THE#
VERY#END# OF# INSTALLATION.
2.#Remove#all factory# screws# from#the
underside# of#the#rear#fender#wheel#wells.
Save#the# factory#screws#for#flare#installation.
**Note:# #Depending#on#the#year,# make# and#model# of#your#
truck,#not#all# the#screws#pictured#on#the#left may# be#there .
2
*( Dr ive r ’s(Sid e (Fr o n t (P ict u r e d
*( Dr ive r ’s(Sid e ( R e ar (P ict u r e d
7.#Secure the# bottom#of#the#rear#flares# with#the#
push#i n#ret ai ners# provided#and/or# the# fac tory#
screws#removed# at#the#beginning#of#installation .#
We provide#l arger# P ush-in#retainers#for# a#tighter#
and#more# se cure# hold.## So#if#the# holes#made#
wi t h #a#1 /4#dril l#bit #are#too #smal l#or#t h e#holes#do#
not#qui t e#l i ne#up#wit h#the#fac tory#hol es,#you#
may#use#a#5 /1 6 #dri l l #bi t #t o#widen#the#holes#
slightly.#If usi ng#sc rews,#DO# NOT# over-ti ghten#as#
this#wil l#pull #the#top#of#the#fl are# from#the#truck#
creating#gaps.
**Note,# depending#on#your#vehicle’s# year, make#and#
model,#you#may# not#use #all#of#the #Push#In#Retainers#
provided.
1Z79X4940347946437
5.##Hol d flare#up#to#the#ve hicle#and#find#the#
factory#hole#positions#on#your#particular#ve hicle#
which #c or respon d#t o #t he#fac tory# h ole#markers#
on#t he# i nt erior#of#the# flare.# #Use# a#¼#inc h#dril l #bit #
to#dril l#a#hole#i n the# middle#of#the#factory#hole#
markers# that#you#i denti fied.
**If you( are(painting( the(fender(fla res,(pre-test(fitment(
and(drill( holes (into(the (factory(hole(marke rs.( (The n,(pre-
test(fitment(a g ain( to(double(check(hole(al ignment(
BEFORE( painti ng.
**Note,# depending#on#your#vehicle’s# year, make#and#
model,#you#may# not#use #all#the#factory# hole#marke rs.
1Z79X4940347946437
6.##Secure the#bottom#of#the# front#fl ares# with#
the#push#i n#retainers# provided#and/or#the#
factory#screws# removed#at#the#beginning#of#
installation.##We provi de#l arger# P ush-in#
ret ainers# for# a#t ighter#and#more#sec u re# h old.##So#
if#the# holes#made#with#a#1/4#drill#bit#are#too#
small#or#the#holes#do#not#quite#line# up#with#the#
factory#holes,#you#may#use#a#5/16#drill#bit#to#
wi d en#t h e#holes# slight ly.##If usi ng#screws,#DO#
NOT# over-tighten#as#thi s#wil l#pull#the#top#of#the#
flare#from#the#truck#creating#gaps.
**Note,# depending#on#your#vehicle’s# year, make#and#
model,#you#may# not#use #all#of#the #Push#In#Retainers#
provided.
3
*( Dr ive r ’s(Sid e ( Fr o n t (P ict u r e d
*( Dr ive r ’s(Sid e ( R e ar (P ict u r e d
*( Dr ive r ’s(Sid e ( Fr o n t (P ict u r e d
4
8.#Double# check# to# make# sure#there# is#no# moisture#or#dirt#in#and#around# the#top#of#the# each#flare.##
Carefully#pull#to#remove# the#rest#of#the#backing#from#the#double# sided#tape#and#firmly#press#the# flare#
against#the#fender#and#hold#f or#20-30#seconds#to #ensure# secure#hold.##If#y ou#are#installing#in#cold#
conditions,# a#hair#drye r#can#be #used#to#heat#up#the#3M#tape#for#better#adhesion.# #DO(NOT(WASH(
TRU CK(OR(GET(THE(FEND ER(AREA(WET(FOR(48(HOURS.
**OPTIONAL( I NS TALLATION**– This(optional( ins tallation( is(for(extra( s ecure(hold(and(is (recomme nde d(IN(ADDITION to(the(standa r d(
installation( and( NOT instead( of(the(standa rd(installation.( (Drive(two(of(the(self-tapping(screws(into(the(flare(and(vehicle(anywhere(in(
be twe e n(the (Pus h(In(Retaine rs.(DO(NOT(over-tighten(a s(this(wil l (pull (the(top(of(the(fla re(from(the(truck(creati ng( gaps.
THANK(YOU( SO(MUCH( FOR(YOUR( PURCH AS E !!
We#hope# you#a re#pleased#with#both# the#product# and#services#you#received.##If#not,#please#a llow#our# exceptional# customer#
service#team#an#opportunity# to#improve#your#experience# before# y ou#leave#a #neg a tive#review.##You#can#conta ct# us#by#
emailing#us#at#the#email#address #lis ted# below# or#call#us#toll# free#at#the#number# also#lis ted# below.##Our#team#is#eagerly#
waiting#to#hel p!
We#a ppreciate# your#business#a nd#want#to#do#everything#to#ensure# that#you#have#a #5-Star# experience# with# us.
If#you#are# happy# with# our# products# and# services,# please#help# us#out# by#sharing#your# experience# with# others# by# leaving#a#
posit ive#review# or#feedback#wherever # you#purchased# our#product s# so#that#they# may#also#benefit# fr om# our# products.
Please#let #us#know#if#you#h ave# any#qu est io n s# or#conc er ns.
Again,#thank #y ou#for#y ou#business#and#we#hope# y ou#enjoy #y our#new#fender# flares!
Warm#Rega rds,
Monkey#Autosports Team
info@monkeyautosports.com
(888)#517-8668
/
