2. Honda
  3. NC 700X Saddlebag Support Brackets
NC 700X Saddlebag Support Brackets

Honda NC 700X Saddlebag Support Brackets Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Honda NC 700X Saddlebag Support Brackets Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Issue Date
INSTALLATION
INSTRUCTIONS
Accessory Application Publication No.
Honda Dealer: Please give a copy of these instructions to your customer.
© 2012 Honda Motor Co., Ltd. - All Rights Reserved.
PARTS LIST
87940-MGS-A300 1 of 9
(6)
SADDLEBAG SUPPORT
BRACKETS
P/N 08L73-MGS-A30
NC700X/XD
Mll 13973
March 2012
No. Description Qty
(1) Right saddlebag hook 1
(2) Left saddlebag hook 1
(3) Right saddlebag hook cover 1
(4) Left saddlebag hook cover 1
(5) 6 mm collar (thick) 4
(6) 6 mm collar (thin/large) 4
(7) Saddlebag bracket 2
(8) 6 mm collar (thin/small) 2
(9) 6 mm collar (medium) 2
(10) 6 mm socket bolt 4
(11) 6 mm flange nut 4
(12) Washer (small) 8
(13) Right saddlebag support stay 1
(14) Left saddlebag support stay 1
(15) Rubber stop 2
(16) 8 mm socket bolt (short) 2
(17) 8 mm socket bolt (medium) 2
(18) 8 mm socket bolt (long) 4
(19) 8 mm collar (long) 4
(20) 8 mm collar (short) 2
(21) Washer (large) 16
(19)
(21)
(18)
(16)
(17)
(10)
(8)
(12)
(9)
(1)
(3)
(4)
(2)
(5)
(11)
(14)
(13)
(7)
(15)
(20)
(12)
© 2012 Honda Motor Co., Ltd. - All Rights Reserved.
2 of 9 87940-MGS-A300
Item N·m kgf·m Ibf·ft
6 mm socket bolt 10 1.0 7
6 mm flange nut 12 1.2 9
8 mm socket bolt 24 2.4 18
Motorcycle’s 8 mm socket bolt 30 3.1 22
TORQUE CHART
Tighten all screws, bolts, and nuts to their specified
torque values. Refer to the Service Manual for the torque
values of the removed parts.
No. Description Qty
(1) Right saddlebag bracket 1
(2) Left saddlebag bracket 1
(3) Plug 4
(4) Molding 1
INSTALLATION INFORMATION
CAUTION:
To prevent burns, allow the engine, exhaust system, •
radiator, etc. to cool before installing accessory.
NOTE:
The rear carrier/saddlebag brackets which are sold •
separately are required to install this accessory.
Take care not to damage the painted surfaces of the •
motorcycle.
When the motorcycle is already equipped with the •
Rear Carrier, remove the Rear carrier and Rear
Carrier/Saddlebag Brackets before installing this
accessory.
USE AND CARE INFORMATION
Check the accessory mounts frequently and •
retighten if necessary.
REAR CARRIER/SADDLEBAG MOUNT BRACKETS
Sold separately
TOOLS AND SUPPLIES REQUIRED
Box-end wrench (10 mm)
Hex wrench (4 and 5 mm)
Electric drill
Hole saw (20 mm)
File
Fret saw
Scissors
Ruler
Wood block 10 mm thick
Marker
Tape
Electrical tape
Isopropyl alcohol
Shop towel
Torque wrench
(1)
(2)
(3)
(4)
For the molding installation, refer to
the included Installation Instructions.
© 2012 Honda Motor Co., Ltd. - All Rights Reserved. 3 of 9
87940-MGS-A300
INSTALLATION
1. Refer to the Service Manual for the motorcycle,
remove the motorcycle parts as shown.
BOLT
DRIVE CHAIN CASE
2. Refer to the Service Manual for the motorcycle,
remove the drive chain case.
BOLT
NUT
FLANGE
COLLAR
SINGLE SEAT
PASSENGER
SEAT
SPRING
WASHER
CLIP
PASSENGER SEAT HINGE
RIGHT GRAB RAIL
LEFT GRAB RAIL
(Save)
CAP
(save)
WASHER
FLANGE
COLLAR
3. Refer to the Service Manual for the motorcycle,
remove the right and left grab rails.
MOTORCYCLE’S
8 mm SOCKET BOLT
MOTORCYCLE’S
8 mm SOCKET BOLT
© 2012 Honda Motor Co., Ltd. - All Rights Reserved.
4 of 9 87940-MGS-A300
RIGHT GRAB RAIL
(Save)
PASSENGER SEAT HINGE
WASHER
WASHER
CLIP
4. Remove the passenger seat hinge as shown.
5. Refer to the Service Manual for the motorcycle,
remove the seat cowl.
BOLT
CLIP
CLIP
SEAT COWL
6. Cut and attach the template to the seat cowl and
mark it using a marker as shown.
SEAT COWL
TAPE
TAPE
TAPE
RIGHT SIDE:
LEFT SIDE:
SEAT COWL
TEMPLATE
TEMPLATE
(Reverse side)
TEMPLATE
MARKER
MARKER
MARKER
Repeat on
the left side.
© 2012 Honda Motor Co., Ltd. - All Rights Reserved. 5 of 9
87940-MGS-A300
7. Remove the template. Cut out the shaded areas on
the seat cowl as shown.
Repeat on the left side.•
FILE
File off the cut surfaces after
removing the area.
SEAT COWL
SEAT COWL
Remove any burrs.
FRET SAW
Remove.
8. Install the seat cowl in the reverse order of removal.
Remove.
REAR FENDER B
WOOD BLOCK
10 mm thick
Position between
the rear fender B
and frame.
Wrap the tape
around the hole
saw leaving 2 mm
of the tip exposed,
as shown, to serve
as a hole saw stop.
ELECTRIC DRILL
(20 mm HOLE SAW)
<If rear fender B has factory marked points>
9. Drill 20 mm holes at the factory marked points on the
rear fender B using an electric drill and hole saw.
Be careful not to damage harnesses.•
Remove any burrs from the edge of the hole.•
Repeat on the left side.•
HOLE SAW
2 mm ELECTRICAL TAPE
© 2012 Honda Motor Co., Ltd. - All Rights Reserved.
6 of 9 87940-MGS-A300
REAR FENDER B
SLIT
<If rear fender B has slits>
9. Work upon the rear fender B as shown.
Be careful not to damage harnesses.•
Remove any burrs from the edge of the hole.•
Repeat on the left side.•
Remove. FILE
File off the
cutout surface.
12. Install the passenger seat hinge as shown.
RIGHT SADDLEBAG
BRACKET
PASSENGER SEAT
HINGE (Reuse)
WASHERS
(Reuse)
CLIP
(Reuse)
BOLT
(Save)
NUT
(Save)
RIGHT SADDLEBAG BRACKET
10. Remove the bolts and nuts as shown.
Repeat on the left side.•
11. Install the right saddlebag hook cover and hook as
shown.
Repeat on the left side.•
RIGHT
SADDLEBAG
BRACKET
WASHER
(small)
6 mm COLLAR
(thin/large)
6 mm COLLAR
(thick)
6 mm
FLANGE NUT
RIGHT SADDLEBAG
HOOK
RIGHT SADDLEBAG
HOOK COVER
© 2012 Honda Motor Co., Ltd. - All Rights Reserved. 7 of 9
87940-MGS-A300
RIGHT SADDLEBAG SUPPORT STAY
14. Loosely install the right saddlebag support stay as
shown.
Repeat on the left side.•
8 mm SOCKET
BOLT (long)
8 mm SOCKET
BOLT (medium)
8 mm SOCKET
BOLT (short)
WASHERS
(large)
WASHERS
(large)
8 mm
COLLAR
(long)
8 mm COLLAR
(short)
RIGHT SADDLEBAG SUPPORT STAY
8 mm COLLAR
(short)
13. Loosely install the saddlebag stays as shown.
Do not install the plugs yet.•
RIGHT SADDLEBAG
BRACKET LEFT
SADDLEBAG
BRACKET
FLANGE COLLAR
(Reuse)
WASHER
(Reuse)
MOTORCYCLE’S
8 mm SOCKET
BOLT (Reuse)
MOTORCYCLE’S
8 mm SOCKET
BOLT (Reuse)
PLUG
Install after
tightening the
bolt securely.
© 2012 Honda Motor Co., Ltd. - All Rights Reserved.
8 of 9 87940-MGS-A300
UPPER BOLTS
17. Install the right saddlebag and tighten all loosely
installed hardware to the specifications in the torque
chart.
When securing the saddlebag support stay, •
first tighten the upper bolts.
Repeat on the left side.•
18. Install the removed parts in the reverse order of
removal.
RIGHT SADDLEBAG
6 mm SOCKET BOLT
SADDLEBAG BRACKET
RIGHT SADDLEBAG
WASHER
(small)
6 mm COLLAR
(middle)
6 mm COLLAR
(thin/small)
16. Install the saddlebag bracket as shown.
Repeat on the left side.•
15. Install the rubber stop as shown.
Make up both brackets.•
SADDLEBAG BRACKET
SADDLEBAG BRACKET
48 mm
RUBBER STOP
RUBBER STOP
© 2012 Honda Motor Co., Ltd. - All Rights Reserved. 9 of 9
87940-MGS-A300
<TEMPLATE>
Cut off along the dotted line.
Align with the
contour of the
seat cowl.
Align with the contour
of the seat cowl.
Align with the contour
of the seat cowl.
Mark along
the template.
Mark along
the template.
Mark along
the template.
First, mark the right side seat cowl.•
Turn the template over to mark the •
left side seat cowl.
Cut this area when used on the left side.•
SCALE
SCALE
NOTICE
If you print this template from your local computer, make
sure the printer settings do not “scale” or “shrink” the page.
/