Page is loading ...
About this item
40V STRING TRIMMER – powers through the toughest grass and weeds
13” CUTTING PATH - .065” line, auto feed head for quick and easy line advancement
TRIMMER / EDGER (2-IN-1) – 90-degree rotating head with edging wheel. 3 position pivoting head for
trimming at multiple angles
VARIABLE SPEED TRIGGER – allows you to control cutting speed on the go, so you can easily maneuver
around plants and shrubs
LIGHTWEIGHT / EASY TO USE - Ultra lightweight design, along with superior ergonomics allow for reduced
user fatigue
MAINTENANCE FREE – This string trimmer is virtually maintenance free, with no gas, no oil, and no
emissions. It starts instantly, is quiet, and delivers to the power you need
Parts Description
Installation
ATTACH THE GUARD
1. Remove the screw (15) from the trimmer head with a Phillips head screwdriver (not
included).
2. Put the guard (9) onto the trimmer head.
3. Align the screw hole on the guard with the screw hole on the trimmer head.
4. Tighten the screw.
ASSEMBLE THE SHAFT
1. Insert the lower shaft into the coupler on the upper shaft.
2. Tighten the coupler (6).
INSTALL THE BATTERY PACK
1. Align the lift ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.
REMOVE THE BATTERY PACK
1. Push and hold the battery release button (16).
2. Remove the battery pack from the machine.
WARNING
● If the parts are damaged, do not use the machine.
● If you do not have all the parts, do not operate the machine.
● If the parts are damaged or missing, speak to the service center.
OPERATION
START THE MACHINE
1. Pull back on the lock-out button (3) and pull the trigger (1).
STOP THE MACHINE
1. Release the trigger to stop the machine.
ADJUST THE LENGTH OF THE CUTTING LINE MANUALLY
1. Stop the machine.
2. Push the spool retainer button (17) and pull on
cutting line to manually advance the cutting line.
3. After you extend new cutter line, always return the
machine to its normal position before you start it
again.
OPERATION TIPS
Do these tips when you use the machine
● Keep a firm hold with the two hands on the machine while you
operate the machine.
● Cut tall grass from the top down.
If grass winds around the trimmer head:
● Remove the battery pack.
● Remove the grass.
CUTTING TIPS
● Tilt the machine toward the area to be cut. Use
the tip of the cutting line to cut grass.
● Move the machine from right to left to prevent
thrown debris from hitting the operator.
● Do not cut in the danger area.
● Do not force the trimmer head into uncut grass.
● Wire and picket fences cause cutting line wear
and breakage. Stone and brick walls, curbs,
and wood can wear the cutting line quickly.
●How do I assemble my Greenworks string trimmer?
Greenworks string trimmers usually require minimal assembly. You will typically need to attach the trimmer head
and handle. Detailed instructions and diagrams can be found in the user manual provided with the trimmer.
Manuals.plus
●What type of string should I use with my Greenworks trimmer?
Greenworks trimmers are compatible with standard trimmer line or string. It is recommended to use 0.065-inch
diameter string for most models. However, check the user manual or product specifications for the specific
string size recommended for your trimmer model.
●Can I use attachments with my Greenworks string trimmer?
Greenworks offers some string trimmers that are compatible with attachments such as edgers, hedge trimmers,
and cultivators. Check the product specifications or the Greenworks website to see if your trimmer model
supports attachments. If it does, you can purchase the appropriate attachments separately.
Manuals.plus
● How do I replace the string on my Greenworks trimmer?
To replace the string, follow these general steps:
Disconnect the trimmer from the power source.
Remove the spool cover or cap on the trimmer head.
Take out the old string or spool.
Insert a new string spool or cut a piece of trimmer line to the appropriate length.
Wind the new string onto the spool following the directional arrows or guides on the spool.
Reinstall the spool or cap onto the trimmer head.
Connect the trimmer to the power source and test the string trimmer.
Manuals.plus
● How do I maintain my Greenworks trimmer?
To keep your Greenworks trimmer in good condition, you can follow these maintenance tips:
Regularly clean the trimmer after each use, removing grass clippings and debris.
Inspect the string or spool for wear and replace as necessary.
Check the trimmer head for any damage or signs of wear.
Keep the trimmer motor and handle clean and free from dirt or oil buildup.
Store the trimmer in a dry place, protected from the elements.
/
