2. FALCON RIDGE
  3. KAW-3010TRANS-WTC01
KAW-3010TRANS-WTC01

FALCON RIDGE KAW-3010TRANS-WTC01 User manual

  • Hello! I am a chat assistant and I have analyzed the document you provided. It includes installation and care instructions for the Falcon Ridge 3010 TRANS WTC01 Windshield/Top Combo. I am ready to answer your questions about the installation process, cleaning, or storage recommendations.
  • What temperature is best for installation?
    What should I use to clean the window panels?
    How should I store the cab enclosure?
5842 Morehead Rd. Flemingsburg, KY 41041
606-845-2227
Instructions for Installation and Care of 3010 TRANS Windshield / Top Combo
KAW-3010TRANS-WTC01
Notice: Do not smoke inside the cab or expose the enclosure to direct flames. Cab is Flammable.
1. Be sure to read these instructions thoroughly before unrolling and installing the
Falcon Ridge 3010 Full Cab Enclosure. The installation is best done when the
temperature is 65 degrees F. or warmer.
2. Carefully unroll the Windshield / Top Combo on a large flat surface that is clean
and free of dirt or other materials.
3. Check over the parts included in the carton with the parts list shown below:
Adhesive Velcro Hook strips: 6 each --------- 8” long
“ “ 1 each --------- 17” long
“ “ 4 each --------- 6” long
W/T Combo 1 each
4. Loosely drape the Cab Enclosure over the Mule roll cage. Note the correct
position for the 17” adhesive hook strip on the brush guard at the front of the
Mule. Clean the area with Isopropyl alcohol, let dry and apply the Velcro hook
strip. Then attach the Cab to the strip around the brush guard.
5. Working your way to the rear of the roll cage, wrap the bars with the supplied 6”
adhesive hook strips immediately above the intake vents. Then stretch the rear of
the enclosure over the back and wrap the double-sided strips around the hook strip
above the vents, overlapping the ends to provide a secure hold. Next locate the
position for the double-sided velcro strips on the center bar located behind the
front seat and repeat the process Be certain to clean the surfaces before applying
the adhesive loop strips!
6. After attaching the rear of the cab and before attaching the Velcro strips on either
side of the windshield it may be necessary to unfasten the front nose piece and
pull it tighter to ensure a good fit.
7. Position and install the six (3 per side) 8” hook and loop strips on the left and
right sides of the roll cage on either side of the front window. Be certain to clean
the surfaces before applying the adhesive loop strips! First, apply all three strips
on one side of the roll cage then pull the window tightly toward the other side to
minimize waviness or wrinkles in the front window.
Cleaning and Storage Recommendations:
1. Before removing the Falcon Ridge Cab for storage, make sure it is very clean in
order to prevent scratching of the window panels. Clean with a soft rag (I
recommend a Flannel or Micro Fiber Cloth) or sponge using a mild liquid
detergent soap and warm water solution. Never rub the windows with a dry cloth
or rag! Let the Cab dry thoroughly before attempting to roll for storage.
2. It is important that the Cab be rolled up for storage rather than folding. Folding
will cause damage to the windows!!! Carefully roll up the Cab similar to the way
it was when it was packed at the factory On a large, clean and flat surface, fold
the doors over the rear panel first, then, interleave the top and windshield on top
of the doors. Begin rolling the Cab into a roll approximately 8 inches in diameter.
Put the rolled Cab back into the carton for storage at a normal room temperature.
It is best not to expose the Cab to either extreme hot or cold temperatures when
storing.
3. A special cleaner conditioner is available from Falcon Ridge that will greatly
increase the service life of the Cab Enclosure. In addition, if additional hook and
loop sets are needed, they can also be ordered.
/