KUZCO EW3609 Installation guide

Type
Installation guide

Below you will find brief information for LED Lamp Wall Sconce EW3609. This document provides instructions for installing the Kuzco LED Lamp Wall Sconce, model EW3609. It includes two sets of instructions depending on your electrical box type, whether it's a single gang or octagon box with an optional backplate. The instructions emphasize the importance of safety, such as turning off the power and wearing gloves during installation, and explain the wiring process, including proper caulking to prevent moisture issues and LED module handling.

Below you will find brief information for LED Lamp Wall Sconce EW3609. This document provides instructions for installing the Kuzco LED Lamp Wall Sconce, model EW3609. It includes two sets of instructions depending on your electrical box type, whether it's a single gang or octagon box with an optional backplate. The instructions emphasize the importance of safety, such as turning off the power and wearing gloves during installation, and explain the wiring process, including proper caulking to prevent moisture issues and LED module handling.

INSTALLATION SHEET
EW3609
Exterior LED Lamp Wall Sconce
START FROM HERE
Please Note:
All Kuzco LED fixtures come with pre-wired LED module(s).
• Unless instructed to do so, please do not touch any part of the LED module(s) as any
unnecessary contact with the module could cause permanent damage.
• For dimming, an ELV (Electronic Low Voltage) type of dimmer is required.
1.
2.
3.
IMPORTANT: To prevent moisture from
entering the outlet box and causing a short,
seal around the top and side perimeter
between the fixture and the wall surface with
weather resistant caulking The space at
bottom should be left un-caulked to prevent
moisture build-up. (See Illustration 01 and 02)
Caulking
2a.
1c.
1b.
1a. 1d. 2b.
Remove the fixture from its original packaging. Remove
the canopy (1c) from within the fixture (2a) by removing
the set screws (2b). Attach the canopy to the electrical
junction box (1a) using the screws (1d) provided in the
hardware package.
Attach all wiring with the provided marettes (1b) (white to
white “N”, black to black “L”, ground to ground “G”).
Direct the fixture (2a) onto the canopy (1c) and secure the
fixture by using the set screws (2b) provided.
For Single Gang Box Instructions
You have now completed the installation of your fixture,
enjoy.
3a.
3e.
3e.
4d.
4a.
3b.
4c.
3c. 3d.
3f. 4b.
You have now completed the installation of your fixture,
enjoy.
1.
2.
3.
Thread the lead wires from the fixture through the canopy
(4a), cover plate (3f), gasket (3g) and through the
mounting bar (3c). Attach all wiring (3b) with the provided
marrets (white to white “N”, black to black “L”, ground to
ground “G”). Next, align the cover plate (3f), gasket (3g)
and canopy (4a) to the screws (3d) and secure with nuts
(4b). With the canopy and cover plate seated on the
mounting bar, secure the fixture (4d) with all set screws
(4c) turning clockwise.
Remove the fixture from its original packaging. Remove
the canopy (4a) by removing the set screws (4c). Attach
the mounting bar (3c) to the electrical junction box (3a),
using the screws (3e) provided.
For Octagon Electrical Box Instructions
(with optional backplate)
3g.
Caulking
Illustration 01
Illustration 02
• Make sure POWER is COMPLETELY OFF at the fuse box
• Have your fixture installed by a qualified licensed electrician
• Prepare everything in a clear area
• Wear gloves at all time during this installation
• Read instructions carefully before you start assembly
• Keep this installation sheet for future reference
Technical Support: 1-855-855-8926
19054 28th Avenue Surrey, BC Canada V3Z 6M3
T: 604 538 7162 TF: 1-855 85 KUZCO F: 604 538 7196
W: kuzcolighting.com
20190814
  • Page 1 1

KUZCO EW3609 Installation guide

Type
Installation guide

Below you will find brief information for LED Lamp Wall Sconce EW3609. This document provides instructions for installing the Kuzco LED Lamp Wall Sconce, model EW3609. It includes two sets of instructions depending on your electrical box type, whether it's a single gang or octagon box with an optional backplate. The instructions emphasize the importance of safety, such as turning off the power and wearing gloves during installation, and explain the wiring process, including proper caulking to prevent moisture issues and LED module handling.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI