Dell PowerEdge 2850 User guide

Type
User guide
www.dell.com | support.dell.com
Dell™ Systems
Activating the Integrated
RAID Controller
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2004 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names
or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
June 2004 P/N F6586 Rev. A00
Activating the Integrated RAID Controller 1-3
This document explains how to activate the integrated RAID controller on Dell™
PowerEdge™ 1850, 2800, and 2850 systems. Your upgrade kit includes a RAID controller
memory module, RAID hardware key, RAID battery, and RAID software.
Before you perform the following procedures, ensure that your PowerEdge 1850 riser card supports
the RAID option. If a memory module connector is not present on the riser card, you have
purchased the standard riser card, which does not support the RAID option. To use the RAID
option, replace the standard riser card with the optional ROMB PCI-X or PCI-Express riser card.
See the
Installation and Troubleshooting Guide
to identify the type of riser card that is installed in
your system.
CAUTION: Only trained service technicians are authorized to remove the system cover and access any
of the components inside the system. See your Product Information Guide for complete information
about safety precautions, working inside the computer, and protecting against electrostatic discharge.
NOTICE: To avoid possible data loss, back up all data on the hard drives before changing the mode
of operation of the integrated SCSI controller from SCSI to RAID.
NOTE: See your Installation and Troubleshooting Guide for detailed instructions on removing
or replacing components.
1
Remove the bezel (if applicable).
2
Turn off the system, including any attached peripherals, and disconnect the AC power
from the electrical outlet.
3
Open the system.
4
If you have a PowerEdge 1850 system, remove the riser card insulator by lifting the two blue
rivets at each end of the insulator, then lift the insulator off of the riser card.
If you have a PowerEdge 2800 system, go to step 5.
If you have a PowerEdge 2850, remove the riser card.
5
Locate the RAID memory module connector on the riser card. See Figure 1-1.
1-4 Activating the Integrated RAID Controller
www.dell.com | support.dell.com
Figure 1-1. Locating the RAID Memory Module
6
Push the ejectors on the RAID memory module connector down and outward to allow
the memory module to be inserted into the connector. See Figure 1-2.
Figure 1-2. Installing the RAID Controller Memory Module
7
Locate the memory module that is included with the upgrade kit.
8
Align the RAID memory module’s edge connector with the alignment key,
and insert the memory module into the connector. See Figure 1-2.
NOTE: Do not substitute unbuffered DDR 2 memory modules such as those used for system memory.
Use the memory module supplied in the RAID upgrade kit.
A
B
SCSI B
SCSI A
RAID battery
RAID battery holder
RAID key
RAID memory module
alignment key
ejectors (2)
Activating the Integrated RAID Controller 1-5
9
Press on the memory module with your thumbs while pulling up on the ejectors with your
index fingers to lock the memory module into the connector.
10
Locate the RAID hardware key connector on the system board. See the system information
label on the inside of the system cover for the location of the RAID key connector.
11
If you have a PowerEdge 1850 system, go to step 13.
12
If you have a PowerEdge 2800 system, remove the memory cooling shroud by lifting
the release latch and sliding the shroud forward.
If you have a PowerEdge 2850 system, lift up the memory cooling shroud.
13
Insert the RAID hardware key into its connector on the system board and secure the key with
the latches on each end of the connector. See Figure 1-3.
14
If you have a PowerEdge 2800 or 2850 system, replace or lower the memory cooling shroud.
15
If you have a PowerEdge 1850 system, install the RAID battery into the RAID battery holder
with the battery cable pointing toward the back of the system.
If you have a PowerEdge 2800 system:
a
Position the RAID battery over the RAID battery holder with the battery cable pointing
toward the front of the system.
b
Insert the cable connector through the notch in the riser, which is adjacent to the SCSIA
connector on the riser.
c
Install the RAID battery into the RAID battery holder.
If you have a PowerEdge 2850 system:
a
Position the RAID battery over the RAID battery holder with the battery cable pointing
toward the front of the system.
b
Route the battery cable through the battery cable securing clip.
c
Install the RAID battery into the RAID battery holder.
See the
Installation and Troubleshooting Guide
for more information.
NOTE: If you are replacing a RAID battery, see the "Battery Disposal" section in your Product Information
Guide for important battery disposal instructions.
16
Connect the RAID battery to the RAID battery cable connector on the riser card.
1-6 Activating the Integrated RAID Controller
www.dell.com | support.dell.com
Figure 1-3. Installing the RAID Key
17
If you have a PowerEdge 1850 system, place the plastic riser card insulator over the riser card
and press down on the two plastic rivets to secure the insulator.
If you have a PowerEdge 2800 system, go to step 18.
If you have a PowerEdge 2850 system, replace the riser card.
18
Close the system.
19
Reconnect the system to its electrical outlet and turn on the system, including any attached
peripherals.
20
Enter the System Setup program and verify that the setting for the SCSI controller has
changed to reflect the presence of the RAID hardware.
21
Install and configure the RAID software. See your RAID documentation for more
information.
NOTICE: The newly-installed RAID battery must be charged for 3 to 4 hours of system operation
before you can operate the RAID controller in write-back mode.
22
Install the bezel (if applicable).
hardware key
latches (2)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Dell PowerEdge 2850 User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI