Dell OEMR R930 User guide

Page is loading ...

RGD3KA04.book Page 2 Monday, November 10, 2014 12:25 PM

Product Information Guide

RGD3KA04.book Page 1 Monday, November 10, 2014 12:25 PM

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

____________________

2014 - 08 P/N RGD3K Rev. A04

RGD3KA04.book Page 2 Monday, November 10, 2014 12:25 PM

Product Information Guide 3

Safety Instructions

For additional important regulatory and safety information for the equipment addressed by this

document, see the Regulatory Compliance website at dell.com/regulatory_compliance.

Additional information for your equipment is available at dell.com/support.

General Safety

WARNING: Observe the following instructions to help prevent potential for property

damage, personal injury, or death.

• The power supplies in your system may produce high voltages and energy hazards.

Opening or removing covers that are marked with the triangle symbol with a lightning bolt

may expose you to a risk of electric shock. Components inside these compartments should

be serviced only by a trained service technician.

The system may have more than one power supply cable. To reduce the risk of

electrical shock, a trained service technician may need to disconnect all power supply cables

before servicing the system.

Where the system regulatory label has the electric current rating suffixed by (X#),

# = maximum number of power supplies per system.

• Do not operate your equipment with any cover(s) removed.

• The internal components, including memory modules, can become extremely hot during

operation. Allow sufficient time to cool before handling.

• Do not use damaged equipment, including exposed, frayed, or damaged power cords.

• When connecting or disconnecting power to hot-pluggable power supplies:

– Install the power supply before connecting the power cable to the power supply.

– Unplug the power cable before removing the power supply.

– Disconnect all sources of power from the system by unplugging all power cables from

the power supplies.

• Do not use the equipment where it can get wet. Protect equipment from liquid intrusion.

If your equipment gets wet, disconnect power to the equipment and to any attached devices.

If the computer is connected to an electrical outlet, turn off the AC power at the

circuit breaker before attempting to remove the power cables from the electrical outlet.

Disconnect any attached devices.

• Do not push any objects into the air vents or openings of the equipment. Doing so can

cause fire or electric shock.

• Do not attempt to service the equipment yourself, except as explained in your

documentation or in instructions otherwise provided to you by the manufacturer.

Always follow installation and service instructions closely.

• If your hardware has a voltage selection switch on the power supply, be sure to set it

for the voltage that most closely matches the AC power available at your location.

RGD3KA04.book Page 3 Monday, November 10, 2014 12:25 PM

4 Product Information Guide

• Operate the equipment only from the type of external power source indicated on the

electrical ratings label.

• To avoid possible damage to the system board, wait 30 seconds after turning off the

equipment before removing a component from the system board or disconnecting

a peripheral device from the equipment.

• For non-rack-mounted servers, leave 10.2 cm (4 in) minimum of clearance on all

vented sides of the equipment to permit the airflow required for proper ventilation.

Restricting airflow can damage the equipment or cause overheating.

• Do not stack equipment or place equipment so close together that it is subject to

re-circulated or preheated air, such as next to an appliance or exhaust vent.

• Ensure that nothing rests on your equipment's cables.

• Move equipment with care; ensure that all casters and/or stabilizers are firmly connected

to the system. Avoid sudden stops and uneven surfaces.

• Review the weight limits referenced in your equipment documentation before placing

a monitor or other device on top of your equipment.

• Use only approved power cable(s) rated for the equipment. The voltage and current rating

of the cable should be greater than the ratings marked on the equipment.

• Plug the equipment power cables into properly grounded electrical outlets.

Do not use adapter plugs or remove the grounding prong from a cable. If you must use

an extension cable, use a 3-wire cable with properly grounded plugs.

• Observe extension cable and power strip ratings. Ensure that the total ampere rating of all

equipment plugged into the extension cable or power strip does not exceed 80 percent of

the ampere ratings limit for the extension cable or power strip.

• To help protect the equipment from fluctuations in electrical power, use a surge suppressor,

line conditioner, or uninterruptible power supply (UPS).

CAUTION: Incorrectly installing a battery or using an incompatible battery may increase

the risk of fire or explosion. Replace the battery only with the same or equivalent type.

• Do not disassemble, crush, or puncture batteries.

• Do not store or place your battery pack next to or in a heat source such as a fire,

heat-generating appliance, car, or exhaust vent. Heating battery cells to temperatures

above 65 °C (149 °F) can cause explosion or fire.

• Do not attempt to open or service batteries. Do not dispose of batteries in a fire or with

household waste. See Battery Disposal instructions.

RGD3KA04.book Page 4 Monday, November 10, 2014 12:25 PM

Product Information Guide 5

WARNING: Additional Instructions for Rack-Mounted Systems.

CAUTION: If installed in a closed or multi-unit rack assembly, the operating ambient

temperature of the rack environment may be greater than room ambient. Therefore,

consideration should be given to installing the equipment in an environment compatible

with the maximum ambient temperature (Tma) specified by the manufacturer. For more

information, see your product documentation.

• Your rack kit has been approved only for the rack cabinet provided. It is your responsibility

to ensure that installation of the equipment into any other rack complies with all

applicable standards. The manufacturer disclaims all liability and warranties with respect

to combinations of equipment with any other rack.

• Before installing your equipment in a rack, install all front and side stabilizers. Failure to

install stabilizers can allow the rack to tip over.

• Always load from the bottom up, and load the heaviest items first.

• Do not overload the AC power supply branch circuit that provides power to the rack.

• Do not stand or step on any components in the rack.

WARNING: Slide/rail mounted equipment is not to be used as a shelf or work space.

Do not add weight to slide/rail mounted equipment.

The following statement applies only to rack-installed products that are

GS-Marked: This equipment is not intended for use at workplaces with visual display units, in

accordance with §2 of the German ordinance for workplaces with visual display units.

WARNING: For equipment using - (48–60) V DC power supplies, a qualified electrician

must perform all connections to DC power and to safety grounds. Do not attempt connecting

to DC power or installing grounds yourself.

CAUTION: Systems using - (48-60) V DC power supplies may have a connection between

the earthed conductor of the DC power supply circuit and the earthing conductor.

RGD3KA04.book Page 5 Monday, November 10, 2014 12:25 PM

6 Product Information Guide

The system using a DC power supply must be connected directly to the system-earthing

electrode conductor, to a bonding jumper from an earthing terminal bar, or the bus to which the

system earthing electrode conductor is connected.

The system using a DC power supply must be located in the same immediate area (such as

adjacent cabinets) as any other equipment that has a connection between the earthed conductor

of the same DC power supply circuit and the earthing conductor, and also the point of earthing

of the DC-powered system.

The DC power supply must be located within the same premises as the equipment.

Switching or disconnecting devices must not be in the earthed circuit conductor between the

source of the DC power supply and the point of the connection of the earthing electrode

conductor.

Instructions for the Qualified Electricians ONLY:

Systems using –(48–60) V DC Power Supplies are intended for restricted access locations in

accordance with Articles 110-5, 110-6, 110-11, 110-14, and 110-17 of the National Electrical

Code, American National Standards Institute (ANSI)/National Fire Protection Association

(NFPA) 70.

Before connecting safety ground or power cables, ensure that the power is removed from the

DC circuit. To ensure that the power is off, locate the circuit breaker on the DC source circuit

(usually at the power distribution of the battery distribution fuse bay). Switch the circuit breaker

to the off position and, if available, install an approved safety locking device on the circuit breaker

or switch.

While grounding techniques may vary, a positive connection to a safety (earth) ground is a

requirement.

When installing the unit, the ground connection must always be made first and disconnected

last to prevent a hazard.

Never defeat the ground conductor or operate the equipment in the absence of a suitably

installed ground conductor. Contact the appropriate electrical inspection authority or an

electrician if you are uncertain that suitable grounding is available.

The system chassis must be securely grounded to the rack cabinet frame. Do not attempt to

connect power to the system until grounding cables are connected.

When stranded wiring is required, use approved wiring termination, such as closed-loop or spade-

type with upturned lugs. These terminations should be the appropriate size for the wires and

must be double crimped, one on the conductor and one on the insulation. For additional

information, see the cabling instructions provided with your system.

RGD3KA04.book Page 6 Monday, November 10, 2014 12:25 PM

Product Information Guide 7

Ergonomic Instructions

WARNING: Improper or prolonged keyboard use may result in injury.

WARNING: Viewing a display or external monitor screen for extended periods of time

may result in eye strain.

Environmental Considerations

Battery Disposal

Refer to your system documentation for battery replacement instructions.

Do not dispose of the battery along with household waste. Contact your local waste disposal

agency for the address of the nearest battery deposit site.

Batteries Directive

In the European Union (EU), this label indicates that the batteries in this

product should be collected separately and not disposed of with household

waste. Substances in batteries can have a potential negative impact on health

and environment and you have a role in recycling waste batteries thus

contributing to the protection, preservation, and improvement of the quality

of the environment. You should contact your local authority or retailer for

details of the collection and recycling schemes available.

Waste Electrical and Electronic Equipment (WEEE) Directive

In the European Union, this label indicates that this product should not be

disposed of with household waste. It should be deposited at an appropriate

facility to enable recovery and recycling.

EU REACH SVHC Disclosure

REACH (Registration, Evaluation, Authorization, and Restriction of Chemicals, EC 1907/2006)

is the European Union’s (EU) chemical substances regulatory framework.

REACH requires the producer to provide customers with sufficient information on Substances

of Very High Concern (SVHC) contained in products in concentration above 0.1% weight by

weight (w/w) to allow safe use of the product.

RGD3KA04.book Page 7 Monday, November 10, 2014 12:25 PM

8 Product Information Guide

EU RoHS

The Restriction of Hazardous Substances Directive (2011/65/EU) is a European Union directive.

Through internal design controls and supply chain declarations, this system has been verified

to comply with the EU RoHS Directive. In addition, eleventh generation (11G) and future

generation base servers have been designed without leveraging EU RoHS exemption 7b: lead in

solders for servers, storage and storage array systems, network infrastructure equipment for

switching, signaling, transmission as well as network management for telecommunications.

This is commonly referred to as RoHS 6/6 compliant.

Regulatory Notices

For additional regulatory information, see the Regulatory Compliance homepage at

http://www.dell.com/regulatory_compliance.

Electromagnetic Interference (EMI) is any signal or emission, radiated in free space or

conducted along power or signal leads, that endangers the functioning of radio navigation

or other safety service or seriously degrades, obstructs, or repeatedly interrupts a licensed radio

communications service. Radio communications services include but are not limited to

AM/FM commercial broadcast, television, cellular services, radar, air-traffic control, pager,

and Personal Communication Services (PCS). These licensed radio services, and unlicensed

radio services, such as WLAN or Bluetooth, along with unintentional radiators such as

digital devices, including computer systems, contribute to the electromagnetic environment.

Electromagnetic Compatibility (EMC) is the ability of items of electronic equipment to

function properly together in the electronic environment. While this computer system has

been designed and determined to be compliant with regulatory agency limits for EMI, there is

no guarantee that interference will not occur in a particular installation.

These products are designed, tested, and classified for their intended electromagnetic

environment. These electromagnetic environment classifications generally refer to the

following harmonized definitions:

• Class B products are intended for use in residential/domestic environments but may also

be used in non-residential/non-domestic environments.

NOTE: The residential/domestic environment is an environment where the use of

broadcast radio and television receivers may be expected within a distance of

10 m from where this product is used.

• Class A products are intended for use in non-residential/non-domestic environments.

Class A products may also be utilized in residential/domestic environments but may

cause interference and require the user to take adequate corrective measures.

If this equipment does cause interference with radio communications services, which can be

determined by turning the equipment off and on, you are encouraged to try to correct the

interference by one or more of the following measures:

• Reorient the receiving antenna.

• Relocate the computer with respect to the receiver.

• Move the computer away from the receiver.

RGD3KA04.book Page 8 Monday, November 10, 2014 12:25 PM

Product Information Guide 9

• Plug the computer into a different outlet so that the computer and the receiver are on

different branch circuits.

If necessary, consult an authorized Technical Support representative or an experienced

radio/television or EMC technician for additional suggestions.

Information Technology Equipment (ITE), including peripherals, expansion cards, printers,

input/output (I/O) devices, monitors, and so on, that are integrated into or connected to the

system should match the electromagnetic environment classification of the computer system.

A Notice About Shielded Signal Cables: Use only shielded cables for connecting peripherals to any

device to reduce the possibility of interference with radio communications services. Using shielded

cables ensures that you maintain the appropriate EMC classification for the intended environment.

It has been determined that this product is a Class A harmonized product. The following sections

provide country-specific EMC/EMI or product safety information.

FCC Notice (U.S. Only)

Class A

This product has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment.

This product generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the manufacturer's instruction manual, may cause harmful interference with radio

communications. Operation of this product in a residential area is likely to cause harmful

interference, in which case you will be required to correct the interference at your own expense. This

device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference that may cause

undesired operation.

Notice: The FCC regulations provide that changes or modifications not expressly approved

by Dell Inc. could void your authority to operate this equipment.

These limits are designed to provide reasonable protection against harmful interference in

a non-residential installation. However, there is no guarantee that interference will not occur in

a particular installation. If this equipment does cause harmful interference with radio or

television reception, which can be determined by turning the equipment off and on, you are

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the antenna of the radio/television receiver.

• Increase the separation between this equipment and the radio/television receiver.

• Plug the equipment into a different outlet so that the equipment and the radio/television

receiver are on different power mains branch circuits.

• Consult an authorized service technician or an experienced radio/television technician for

additional suggestions.

RGD3KA04.book Page 9 Monday, November 10, 2014 12:25 PM

10 Product Information Guide

Company name: Dell Inc. is the responsible party for this product. For an EMC compliance issue

or a regulatory inquiry, please use the following contact information:

Dell Inc.

Worldwide Regulatory Compliance, Engineering and Environmental Affairs

One Dell Way PS4-30

Round Rock, Texas 78682 USA

512-338-4400

Industry Canada, Class A

This Class A digital apparatus complies with Canadian ICES-003.

Notice: The Industry Canada regulations provide that changes or modifications not expressly

approved by Dell Inc. could void your authority to operate this equipment.

Industry Canada, Classe A

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Avis: Dans le cadre des réglementations d'Industry Canada, vos droits d'utilisation de cet

équipement peuvent être annulés si des changements ou modifications non expressément

approuvés par Dell Inc. y sont apportés.

CE Notice

This product has been determined to be in compliance with 2006/95/EC (Low Voltage Directive),

2004/108/EC (EMC Directive), and amendments of the European Union. Versions of this

product may have integrated modules or add-in cards supporting wireless and

telecommunications operations. These wireless and telecommunications peripherals have been

assessed as compliant in this product and, when present, are in compliance with 1999/5/EC

(R&TTE Directive, for Radio and Telecommunications Interfaces).

European Union, Class A

WARNING: This is a Class A product. In a domestic environment this product may cause radio

frequency interference in which case the user may be required to take adequate measures.

A "Declaration of Conformity" in accordance with the preceding directives and standards has

been made and is on file at Dell Inc. Products Europe BV, Limerick, Ireland.

Simplified Chinese Class A Warning Notice (China Only)

RGD3KA04.book Page 10 Monday, November 10, 2014 12:25 PM

Product Information Guide 11

VCCI Notice (Japan Only)

KCC Notice (Republic of Korea Only)

다음은 KCC 규정 준수에 따라 본 설명서에서 언급하고 있는 A등급 장치에 관한 것입니다.

• 인증 수취인: Dell Inc.

Worldwide Regulatory Compliance, Engineering

and Environmental Affairs

One Dell Way PS4-30

Round Rock, Texas 78682 USA

512-338-4400

• 장비 또는 모델명: 이 정보에 관한 제품 레이블을 참조하십시오.

• 인증 번호: KCC 로고 바로 밑에 있는 인증 번호를

참조하십시오.

• 제조일: 각각의 제품에는 제조 날짜가 인쇄되어

있습니다. 이 날짜는 바코드 형태로 되어 있을

것입니다.

• 제조국가: 이 정보에 관한 제품 레이블을 참조하십시오.

상기 각각의 제품에는 제조 날짜가 인쇄되어 있습니다 .

RGD3KA04.book Page 11 Monday, November 10, 2014 12:25 PM

12 Product Information Guide

BSMI Notice (Taiwan Only)

RGD3KA04.book Page 12 Monday, November 10, 2014 12:25 PM

产品信息指南

RGD3KA04.book Page 13 Monday, November 10, 2014 10:20 AM

Page is loading ...

22 产品信息指南

RGD3Kcsb4.fm Page 22 Tuesday, November 11, 2014 5:19 AM

產品資訊指南

RGD3KA04.book Page 25 Friday, November 7, 2014 1:28 PM

Page is loading ...

32 產品資訊指南

RGD3KA04.book Page 32 Friday, November 7, 2014 1:28 PM

Příručka s informacemi o produktu

RGD3KA04.book Page 33 Monday, November 10, 2014 12:25 PM

Page is loading ...

Guide d'information sur le produit

RGD3KA04.book Page 43 Monday, November 10, 2014 12:25 PM

Page is loading ...

54 Guide d'information sur le produit

RGD3KA04.book Page 54 Monday, November 10, 2014 12:25 PM

Page is loading ...

Dell OEMR R930 User guide

Dell OEMR R930 User guide

in other languages