Jeep 2020 Wrangler Reference guide

Brand: Jeep

Model: 2020 Wrangler

Category: Cars

Type: Reference guide

This manual is also suitable for

Wrangler

2020 WRANGLER

QUICK REFERENCE GUIDE

VEHICLE USER GUIDE —

IF EQUIPPED

VEHICLE USER GUIDE — IF

EQUIPPED

To access the Vehicle User Guide on your

Uconnect Touchscreen: Tap the Uconnect

Apps button, then tap the Vehicle User Guide

icon on your touchscreen. No Uconnect

registration is required.

Uconnect 4C NAV With 8.4-inch Display Vehicle

User Guide Touchscreen Icon

NOTE:

Vehicle User Guide features are not available

while the vehicle is moving.

Features

• Your User Guide — Updated in real time

• Available when and where you need it

• Touchscreen convenience

• Customizable interface

• Maintenance schedules and information

• Multilingual

• Comprehensive icon and symbol glossary

For further information, and applicable warn-

ings and cautions, please refer to the

Owner’s Manual at

www.mopar.com/en-us/

care/owners-manual.html

(U.S. Residents) or

www.owners.mopar.ca

(Canadian Residents).

KEYLESS ENTER-N-GO —

PASSIVE ENTRY

INTRODUCTION TO

KEYLESS ENTER-N-GO

The Keyless Enter-N-Go — Passive Entry

system is an enhancement to the vehicle’s

key fob. This feature allows you to lock and

unlock the vehicle’s door(s) without having

to push the key fob lock or unlock buttons as

well as starting and stopping the vehicle with

the push of a button.

TO LOCK THE VEHICLE’S

DOORS

With a valid Keyless Enter-N-Go key fob

within 5 ft (1.5 m) of the driver or passenger

front door handles, push door handle lock

button to lock all doors.

20_JL_QRG_EN_USC_t.book Page 1

Do NOT grab the door handle, when pushing

the door handle lock button. This could

unlock the door(s).

Push The Button To Lock

Do NOT Grab The Handle When Locking

NOTE:

• After pushing the door handle lock button,

you must wait two seconds before you can

lock or unlock the doors, using either

Passive Entry door handle. This is done to

allow you to check if the vehicle is locked

by pulling the door handle without the

vehicle reacting and unlocking.

• The Passive Entry system will not operate

if the key fob battery is depleted.

The vehicle doors can also be locked by using

the key fob lock button or the lock button

located on the vehicle’s interior door panel.

TO UNLOCK FROM THE

DRIVER OR PASSENGER

SIDE

Grab The Door Handle To Unlock

With a valid Keyless Enter-N-Go key fob

located outside the vehicle and within 5 ft

(1.5 m) of the driver or passenger side door

handle, grab either front door handle to

unlock the door automatically.

20_JL_QRG_EN_USC_t.book Page 2

TO UNLOCK/LOCK THE

SWING GATE

To Unlock/Enter The Swing Gate

The Swing Gate Passive Entry unlock feature

is built into the handle of the swing gate.

With a valid Passive Entry key fob within 5 ft

(1.5 m) of the swing gate, pull the swing gate

handle to open with one fluid motion.

Swing Gate Passive Entry Location

To Lock The Swing Gate

With a valid Passive Entry key fob within 5 ft

(1.5 m) of the swing gate, push the Passive

Entry lock button located on the outside

swing gate door handle.

NOTE:

The Swing Gate Passive Entry lock button

will lock all doors and the swing gate. The

swing gate unlock feature is built into the

swing gate handle.

DOORS

FRONT DOOR REMOVAL

Door Removal Warning Label

NOTE:

• Doors are heavy; use caution when removing

them.

• Hinge pin can break if overtightened during

door reinstall (Max Torque: 7.5 ft·lb / 10 N·m).

• When front doors are removed, the

message “Blind Spot Alert Temporarily

Unavailable” will display in the instru-

ment cluster display. Power Mirrors and

Power Door Locks will also be unavailable.

1. Roll down the glass window to prevent

any damage.

2. Remove the hinge pin screws from the

upper and lower outside hinges (using a

#T50 Torx head driver).

NOTE:

The hinge pin screws and nuts can be stowed

in the rear cargo tray located under the rear

load floor.

Hinge Pin Screw

20_JL_QRG_EN_USC_t.book Page 3

3. Remove the plastic wiring access door

under the instrument panel by sliding the

plastic panel along the door frame toward

the seats until the tabs are detached.

Wiring Access Door

NOTE:

Do not pry back to open, as this will break

the plastic cover.

4. Pull up on the red locking tab to unlock

the wiring harness.

Closed Wiring Harness

5. Push and hold down the black security

tab under the wiring harness, and lift the

harness into the open position.

6. With the wiring harness open, pull down-

ward on the wiring connector to unplug.

Store wiring connector in the lower door

basket.

7. Remove the check screw from the center

door check (using a #T40 Torx head

driver).

Door Check (Detached)

8. With the door open, lift the door with the

help of another person, to clear the hinge

pins from their hinges and remove the

door.

To reinstall the door(s), perform the previous

steps in the opposite order.

NOTE:

The upper hinge has a longer pin, which can

be used to assist in guiding the door into

place when reinstalling.

1 – Locking Tab

2 – Wiring Harness

20_JL_QRG_EN_USC_t.book Page 4

REAR DOOR REMOVAL

(FOUR-DOOR MODELS)

Door Removal Warning Label

NOTE:

• Doors are heavy; use caution when removing

them.

• Hinge pin can break if overtightened during

door reinstall (Max Torque: 7.5 ft·lb / 10 N·m).

1. Roll down the glass window to prevent

any damage.

2. Remove the hinge pin screws from the

upper and lower outside hinges (using a

#T50 Torx head driver).

NOTE:

The hinge pin screws and nuts can be stowed

in the rear cargo tray located under the rear

load floor.

3. Slide the front seat(s) fully forward.

4. Pry open and remove the plastic wiring

access door from the bottom of the

B-pillar.

5. Unplug the wiring connector.

NOTE:

Squeeze the tab on the base of the wiring

harness. This will unlock the connector tab,

allowing the wiring connector to be

unplugged.

Wiring Connector

6. Remove the check screw from the center

door check (using a #T40 Torx head

driver).

7. With the door open, lift the door with the

help of another person, to clear the hinge

pins from their hinges and remove the

door.

To reinstall the door(s), perform the previous

steps in the reverse order.

NOTE:

The upper hinge has a longer pin, which can

be used to assist in guiding the door into

place when reinstalling.

20_JL_QRG_EN_USC_t.book Page 5

SEATS

EASY ENTRY SEAT —

TWO-DOOR MODELS

Pull upward on the easy entry lever located

on the outboard side of the seat back, and

slide the entire seat forward.

Easy Entry Lever

To return the seat to a sitting position, fold

the seatback upright until it locks and push

the seat rearward until the track locks.

FOLD AND TUMBLE REAR

SEAT — TWO-DOOR

MODELS

Folding The Rear Seat

1. Lift the seatback release lever, located

on the seatback between the head

restraints, and fold the seatback forward.

2. Slowly flip the entire seat forward.

3. Use the two retention straps located on the

back of the rear seat and two corresponding

wire loops located on the back of each

B-pillar, and thread the hook-and-loop

fasteners on the straps through the loops to

secure the seat in the folded position.

Rear Seat Tumble Position Retention Strap

FOLDING REAR SEAT —

FOUR-DOOR MODELS

To fold the seat, lift upward on the seatback

release lever, located on the outboard sides

of the rear seat, and slowly fold down the

seatback. The head restraint will fold auto-

matically with the seat when this lever is

pulled.

Seatback Release Lever

20_JL_QRG_EN_USC_t.book Page 6

STARTING AND

OPERATING

FOUR-WHEEL DRIVE

OPERATION

Four And Five Position Transfer Case

Four Position Four-Wheel Drive Gear Selector

The transfer case provides the following

mode positions:

Two-Wheel Drive High Range — This range is

for normal street and highway driving on dry,

hard surfaced roads.

4H AUTO — If Equipped

Four-Wheel Drive Auto High Range — This

range sends power to the front wheels. The

four-wheel drive system will be automatically

engaged when the vehicle senses a loss of

traction. Additional traction will be provided

for varying road conditions.

4H / 4H PART-TIME (P-T)

Four-Wheel Drive High Range — This range

maximizes torque to the front driveshaft,

forcing the front and rear wheels to rotate at

the same speed. This range provides addi-

tional traction for loose, slippery road

surfaces only.

NEUTRAL (N)

Neutral — This range disengages both the

front and rear driveshafts from the power-

train. To be used for flat towing behind

another vehicle.

Four-Wheel Drive Low Range — This range

provides low speed four-wheel drive. It maxi-

mizes torque to the front driveshaft, forcing

the front and rear wheels to rotate at the

same speed. This range provides additional

traction and maximum pulling power for

loose, slippery road surfaces only. Do not

exceed 25 mph (40 km/h).

This transfer case is designed to be driven in

the two-wheel drive position (2WD) or

four-wheel drive position (4WD AUTO) for

normal street and highway conditions on dry

hard surfaced roads. Driving the vehicle in

2WD will have greater fuel economy benefits

as the front axle is not engaged in 2WD.

For variable driving conditions, the 4WD

AUTO mode can be used. In this mode, the

front axle is engaged, but the vehicle's power

is sent to the rear wheels. Four-wheel drive

will be automatically engaged when the

vehicle senses a loss of traction. Because the

front axle is engaged, this mode will result in

lower fuel economy than the 2WD mode.

In the event that additional traction is

required, the transfer case 4H, 4H P-T and

4L positions can be used to lock the front and

rear driveshafts together, forcing the front

and rear wheels to rotate at the same speed.

The 4H, 4H P-T and 4L positions are

intended for loose, slippery road surfaces

only and not intended for normal driving.

20_JL_QRG_EN_USC_t.book Page 7

Driving in the 4H, 4H P-T and 4L positions

on hard-surfaced roads will cause increased

tire wear and damage to the driveline compo-

nents. Refer to “Shifting Procedures” in this

section for further information on shifting

into 4H, 4H P-T or 4L.

When operating your vehicle in 4L, the engine

speed will be approximately three times (four

times for Rubicon models) that of the 2H, 4H,

or 4H P-T positions at a given road speed. Take

care not to overspeed the engine.

Shifting Procedures

2H To 4H/4H Auto Or 4H/4H Auto To 2H

Shifting between 2H and 4H/4H Auto can be

made with the vehicle stopped or in motion.

The preferred shifting speed would be 0 to

45 mph (72 km/h). With the vehicle in

motion, the transfer case will engage/disen-

gage faster if you momentarily release the

accelerator pedal after completing the shift.

Do not accelerate while shifting the transfer

case. Apply a constant force when shifting

the transfer case lever.

2H To 4H/4H Part Time/ 4H Auto Or 4H/4H Part

Time/ 4H Auto To 2H

With the vehicle rolling at 2 to 3 mph (3 to

5 km/h), shift an automatic transmission

into NEUTRAL (N), or press the clutch pedal

on a manual transmission. While the vehicle

is coasting at 2 to 3 mph (3 to 5 km/h), shift

the transfer case lever firmly to the desired

position. Do not pause with the transfer case

in N (Neutral). Once the shift is completed,

place the automatic transmission into DRIVE

or release the clutch pedal on a manual

transmission.

2H/4H Auto To 4H Part Time Or 4H Part Time To

2H/4H Auto

Shifting between 2H/4H Auto to 4H Part

Time can be made with the vehicle stopped

or in motion. The preferred shifting speed

would be 0 to 45 mph (72 km/h). With the

vehicle in motion, the transfer case will

engage/disengage faster if you momentarily

release the accelerator pedal after

completing the shift. Do not accelerate while

shifting the transfer case. Apply a constant

force when shifting the transfer case lever.

4H Part Time/4H Auto To 4L Or 4L To 4H Part

Time/4H Auto

With the vehicle rolling at 2 to 3 mph (3 to

5 km/h), shift the automatic transmission

into NEUTRAL (N), or press the clutch pedal

on a manual transmission. While the vehicle

is coasting at 2 to 3 mph (3 to 5 km/h), shift

the transfer case lever firmly to the desired

position. Do not pause with the transfer case

in N (Neutral). Once the shift is completed,

place the automatic transmission into DRIVE

or release the clutch pedal on a manual

transmission.

NOTE:

• Shifting into or out of 4L is possible with the

vehicle completely stopped; however, diffi-

culty may occur due to the mating teeth not

being properly aligned. Several attempts

may be required for clutch teeth alignment

and shift completion to occur. The preferred

method is with the vehicle rolling at 2 to

3 mph (3 to 5 km/h). Avoid attempting to

engage or disengage 4L with the vehicle

moving faster than 2 to 3 mph (3 to 5 km/h).

20_JL_QRG_EN_USC_t.book Page 8

• Do not attempt to make a shift while only the

front or rear wheels are spinning. The front

and rear driveshaft speeds must be equal for

the shift to take place. Shifting while only the

front or rear wheels are spinning can cause

damage to the transfer case.

• Delayed shifts out of four-wheel drive may

be experienced due to uneven tire wear,

low or uneven tire pressures, excessive

vehicle loading, or cold temperatures.

• Shifting effort will increase with speed,

this is normal.

During cold weather, you may experience

increased effort in shifting until the transfer

case fluid warms up. This is normal.

Sway Bar Disconnect

Your vehicle may be equipped with an elec-

tronic disconnecting stabilizer/sway bar. This

system allows greater front suspension travel

in off-road situations.

This system is controlled by the SWAY BAR

switch located on the instrument panel (to

the right of the steering column).

Sway Bar Switch

Push the SWAY BAR switch to activate the

system. Push the switch again to deactivate the

system. The “Sway Bar Indicator Light”

(located in the instrument cluster) will illumi-

nate when the bar is disconnected. The “Sway

Bar Indicator Light” will flash during activation

transition, or when activation conditions are not

met. The stabilizer/sway bar should remain in

on-road mode during normal driving conditions.

To disconnect the stabilizer/sway bar, shift to

either 4H or 4L and push the SWAY BAR switch

to obtain the off-road position. Refer to

“Four-Wheel Drive Operation” in this section for

further information. The “Sway Bar Indicator

Light” will flash until the stabilizer/sway bar

has been fully disconnected.

To return to on-road mode, push the SWAY

BAR switch again.

Axle Lock (Tru-Lok) — Rubicon Models

The AXLE LOCK switch is located on the

instrument panel (to the right of the steering

column).

Axle Lock Switch Panel

20_JL_QRG_EN_USC_t.book Page 9

This feature will only activate when the

following conditions are met:

• Ignition in ON/RUN position, vehicle in 4L

range.

• Vehicle speed should be 10 mph (16 km/h)

or less.

• Both right and left wheels on axle are at

the same speed.

To activate the system, push the AXLE LOCK

switch down to lock the rear axle only (the

“REAR ONLY” will illuminate), push the

switch up to lock the front axle and rear axle

(the “FRONT + REAR” will illuminate).

When the rear axle is locked, pushing the

bottom of switch again will lock or unlock the

front axle.

NOTE:

The indicator lights will flash until the axles

are fully locked or unlocked.

To unlock the axles, push the AXLE LOCK

OFF button.

The axle lock disengages at speeds above

30 mph (48 km/h), and will automatically

re-lock once vehicle speed is less than

10 mph (16 km/h).

ENGINE STOP/START

SYSTEM (ESS)

The Stop/Start system was developed to

reduce emissions and will turn back on every

time the ignition is turned OFF and then

back ON again. The system defaults back on

at every ignition cycle.

Stop/Start OFF Switch

The system will stop the engine automatically

during a vehicle stop if the required conditions

are met.

Releasing the brake pedal or pressing the

accelerator pedal will start the engine on a

vehicle equipped with an automatic trans-

mission. Pressing the clutch pedal will auto-

matically restart the engine on a vehicle

equipped with a manual transmission.

How do I manually turn off/on the engine Stop/

Start system?

• Press the Stop/Start OFF switch (located

on the switch bank). The light on the

switch will illuminate when the system is

off. The light on the switch will turn off

when system is on.

What are possible reasons the engine does not

autostop?

• The hood is ajar.

• Driver’s door is open.

• Driver’s seat belt is unbuckled.

• The transmission is not in a forward gear.

• The vehicle is in 4L transfer case mode (if

equipped).

20_JL_QRG_EN_USC_t.book Page 10

• The vehicle has not reached a speed of

5 mph (8 km/h) after the previous

autostop.

• Outside temperature is too cold or too hot

for system to operate.

• Engine has not reached normal operating

temperature.

• Cabin heating or cooling is in process and

an acceptable cabin temperature or setting

has not been achieved.

• Many of these reasons are displayed as a

STOP/START message in the instrument

cluster display within the Stop/Start

section. The system must be in the “STOP/

START READY” state to autostop. To

access the Stop/Start section of the instru-

ment cluster display, use the display

controls.

How do I know I am in an autostop?

• The engine will shut down, the tachometer

will move to the zero position and the Stop/

Start telltale will illuminate in the instru-

ment cluster.

How do I start the engine while in an autostop?

• While in a forward gear, the engine will

start when the brake pedal or clutch is

pressed or released or the throttle pedal is

depressed. The automatic transmission

will re-engage upon engine restart.

PHONE PAIRING

PAIRING PROCEDURE

Mobile phone pairing is the process of estab-

lishing a wireless connection between a

cellular phone and the Uconnect system.

Start Pairing Procedure On The Radio

Uconnect 4C/4C NAV:

Uconnect 4C/4C NAV

1. Place the ignition in the ACC or ON/RUN

position.

2. Tap the Phone icon in the Menu Bar on

the touchscreen.

• If no phone is connected to the vehicle, a

message will display asking to pair a phone.

Select “Yes” to this message. After pressing

“Yes”, the radio prompts will take you

through the steps to connect your phone via

Bluetooth®.

20_JL_QRG_EN_USC_t.book Page 11

• Uconnect Phone will display an “In

progress” screen while the system is

connecting. A message will display if

pairing is successful. Click “OK” to

this message.

Phone pairing can also be accessed by:

1. Placing the ignition in the ACC or ON/

RUN position.

2. Pressing the Apps button in the Menu

Bar on the touchscreen.

3. Pressing “Settings”.

4. Pressing “Phone/Bluetooth®”.

5. Pressing “Paired Phones and Audio

Devices”

6. Pressing “Add Devices”

Then, proceed to follow on-screen instruc-

tions to pair phone with vehicle.

NOTE:

Uconnect Phone will display an “In prog-

ress” screen while the system is connecting.

NOTE:

During the pairing procedure, you may

receive a pop-up on your mobile phone for

the Uconnect System to access your

“messages” and “contacts”. Selecting “Ok”

or “Allow” will sync your contacts with the

Uconnect System.

Pair Your iPhone®:

For further information on how to activate

Bluetooth® on your iPhone®, refer to your

phone’s User Manual.

Complete The iPhone® Pairing Procedure:

After Bluetooth® is activated on your mobile

phone, confirm the passkey shown on the mobile

phone matches the passkey shown on the Ucon-

nect system, then accept the Bluetooth® pairing

request.

Pair Your Android™ Device:

For further information on how to activate

Bluetooth® on your Android® device, refer

to your phone’s User Manual.

Complete The Android™ Pairing Procedure:

After Bluetooth® is activated on your mobile

phone, confirm the passkey shown on the mobile

phone matches the passkey shown on the Ucon-

nect system, then accept the Bluetooth® pairing

request.

For further information on Uconnect Phone,

please refer to “Uconnect Phone” in the

vehicle’s Owner’s Manual or the Uconnect

Supplement.

20_JL_QRG_EN_USC_t.book Page 12

FRONT USB PORT/AUDIO

JACK (AUX) PORT

USB PORT

Media Hub

This feature allows an iPod® or external USB

device to be plugged into the USB port. The

USB port supports certain iPod® and

iPhone® devices. The USB port also

supports playing music from external USB

devices. Some iPod® software versions may

not fully support the USB port features.

Please visit Apple’s® website for iPod® soft-

ware updates. Connect your iPod® or

compatible device using a USB cable

connected to the USB port. USB memory

sticks with audio files can also be used.

Then, audio from the device can be played

on the vehicle’s sound system while

providing the artist, track title, and album

information on the radio display (if available

on device). When connected, the iPod®/USB

device can be controlled using the radio or

steering wheel audio controls to play, skip to

the next or previous track, browse, and list

the contents.

USB Connection

NOTE:

Two devices can be plugged in at the same

time and both ports will provide charging capa-

bilities. Only one port can transfer data to the

system at a time. A pop-up will appear and

allow you to select the device transferring data.

For example, if a device is plugged into the

Type A USB port and another device is

plugged into the Type C USB port, a message

will appear and allow you to select which

device to use.

For additional information, refer to your

Owner’s Manual Supplement.

AUX/AUDIO JACK

The AUX/audio jack provides a means to

connect a portable audio device, such as an

MP3 player, to the vehicle’s sound system.

This requires the use of a 3.5 mm stereo

audio patch cable. AUX mode is entered by

pushing the Media button. Once in Media

mode, select the AUX button when the audio

jack is connected. Volume on the connected

device may need to be adjusted to optimize

audio quality.

1 — AUX Port

2 — Type C USB Port

3 — Type A USB Port

20_JL_QRG_EN_USC_t.book Page 13

SIRIUSXM GUARDIAN™

— IF EQUIPPED

ACTIVATION

Activate your account to enjoy advanced

safety, security and convenience features.

1. Press the Apps icon on the bottom of your

in-vehicle touchscreen.

2. Select the “Activate Services” icon from

your list of apps.

3. Select “Customer Care” to speak with a

SiriusXM Guardian™ Customer Care

agent who will activate services in your

vehicle, or select “Enter Email” to acti-

vate on the web.

Once you have activated your services, you’re

only a few steps away from using remote

services.

Mobile App

Download the Uconnect mobile app:

• Once downloaded, use your Owner Account

• A PIN is required to execute remote

services.

• Tap the Location button on the bottom

menu bar of the app to locate your vehicle

or send a destination to your Uconnect

Navigation (if equipped).

• Tap the “Settings” side menu in the upper

left corner of the app to bring up app

settings and access the Assist Call

Centers.

For further information:

• US residents visit:

www.driveucon-

nect.com/sirius-xm-guardian

• Canadian residents visit:

www.siriusxm.ca/

guardian-v1/

20_JL_QRG_EN_USC_t.book Page 14

FEATURES

In-Vehicle

SiriusXM Guardian™ enhances your owner-

ship and driving experience by connecting

your vehicle to an operable network. When

connected to an operable network, you have

access to:

• SOS Call: Connect to a live agent who will

contact emergency services and stay on

the line with you until help arrives.

• Customer Care Assistance: Speak with a

live agent by pressing the ASSIST button

on your overhead console to get Roadside

Assistance or support.

Remote Services

• Vehicle Finder helps you find where you

parked your car.

• Send & Go allows you to send destinations

to your navigation system for easy access

on the go.

• Remote Door Lock/Unlock lets you unlock

or lock your doors from any distance.

• Remote Horn & Lights allows you to sound

your horn and flash your lights to easily

find your car.

• Receive monthly Vehicle Health Reports

and Alerts whenever a problem is detected

under the hood.

Security Services

• Receive stolen vehicle assistance, using

GPS technology to help authorities locate

your vehicle if it is stolen.

SiriusXM Guardian™ remote services can be

used with the Uconnect app from virtually

anywhere.

For further information on SiriusXM

Guardian™ or the Uconnect mobile App, refer

to your Uconnect Owner’s Manual Supplement.

VEHICLE FINDER AND SEND

& GO

Vehicle Finder

Vehicle Finder allows you to find the location

of your vehicle. To find your vehicle:

1. Press the “Location” tab on the Ucon-

nect mobile App bottom bar.

2. Select the “Vehicle” icon to determine

the location of your vehicle.

3. Select the Find Route button that

appears, once your vehicle is located.

4. Select your preferred Navigation app to

route a path to your vehicle.

20_JL_QRG_EN_USC_t.book Page 15

Send & Go

To send an address to your Uconnect Naviga-

tion using the Uconnect mobile app:

1. Press the “Location” tab on the bottom

bar of the Uconnect mobile app.

2. Type in the destination you would like to

navigate to or search through one of the

categories provided.

3. Select the destination you want to send

from the list that appears.

4. Press the Send To Vehicle button, and

then confirm the destination by pressing

“Yes” to send the destination to the

Uconnect Navigation in your vehicle.

5. Finally, confirm the destination inside

your vehicle by pressing the “Go Now”

option on the pop-up that appears on the

touchscreen when the vehicle is started.

AMAZON ALEXA® — IF

EQUIPPED

Amazon Alexa®

Alexa® is Amazon’s cloud-based voice

service, and it lets you voice-command your

Uconnect system from just about anywhere.

To link your Uconnect system to Amazon

Alexa®:

1. Download the Amazon Alexa® app on

your iPhone® or Android™.

2. Launch the app, then tap MENU, and go

to SKILLS.

3. Search for your vehicle. Then tap

“ENABLE.”

4. Select LINK ACCOUNT.

5. Log in using your vehicle’s Owner

Account ID and password.

Examples of commands:

• “Alexa®, ask Dodge Durango how much

gas is in my vehicle.”

• “Alexa®, ask Jeep® Grand Cherokee to

send directions to Iron Mountain to my

vehicle.”

• “Alexa®, ask Chrysler 300 to start my

vehicle.”

20_JL_QRG_EN_USC_t.book Page 16

ANDROID AUTO™ AND

APPLE CARPLAY® — IF

EQUIPPED

ANDROID AUTO™

INTEGRATION

Android Auto™ And LTE Data Coverage

With easy touchscreen navigation and voice

recognition (VR), Android Auto™ brings

useful information and organizes it into

simple cards that appear just when they are

needed.

1. Download the Android Auto™ app from

the Google Play store on your

Android™-powered smartphone.

2. Connect your Android™-powered smart-

phone to one of the media USB ports in

your vehicle. If the Android Auto™ app

was not downloaded, it will begin to

download when you plug in your device.

3. Once the device is connected and recog-

nized, the “Phone” icon on the personal-

ized menu bar will automatically change

to the Android Auto™ Icon.

APPLE CARPLAY®

INTEGRATION

Apple CarPlay® is the smarter, safer way to

use your iPhone® to get directions with

Apple® Maps, listen to Apple Music®, make

calls and send messages — all through the

Uconnect touchscreen or with your voice

through Siri.

Apple CarPlay® And LTE Data Coverage

20_JL_QRG_EN_USC_t.book Page 17

To use Apple CarPlay®, make sure you are

using iPhone® 5 or later, have Siri enabled

in Settings, ensure your iPhone® is unlocked

for the very first connection only, and then

follow these steps:

1. Connect your iPhone® to one of the

media USB ports in your vehicle.

2. Once the device is connected and recog-

nized, the Phone icon on the personal-

ized menu bar will automatically change

to the Apple CarPlay® icon.

NOTE:

Long Press: Press and hold the VR button to

activate Siri or Google Assistant.

Short Press: Briefly tap the VR button to acti-

vate the native Uconnect Voice Recognition

system.

When using Android Auto™ or Apple

CarPlay®, be sure to use the

factory-provided cable that came with your

phone, as aftermarket cables may not work.

JEEP VEHICLE OWNER’S

MOBILE APP

NOTE:

The Owner’s Mobile App content is appli-

cable to vehicles sold in the US market and

are not available from the Canadian App

Store® or Google Play Store.

KEY FEATURES

• Owner Information For Your Vehicle

• Accident Assistant

• Online Service Scheduling

• Roadside Assistance

• Maintenance History

• And More

To get this FREE application, go directly to

the App Store® or Google Play Store and

enter the search keyword “Jeep”.

The Jeep Vehicle Owner’s Information Appli-

cation is the essential app for owners of Jeep

brand vehicles. The app puts driver and life-

style information right in the palm of your

hand, anywhere you go. Whether it’s providing

information about specific product features,

taking a tour through your vehicle’s equip-

ment, staying up-to-date on your vehicle’s

health, knowing what steps to take following

an accident, or scheduling your next appoint-

ment, we know you’ll find the app an

important extension of your Jeep vehicle.

Simply download the FREE app, select your

make and model, and enjoy the ride.

FEATURES/BENEFITS

• Available for free on iOS and Android™

smartphones and tablets.

• Select Jeep brand vehicles from model

year 2011 to current model year.

• You can also add other Chrysler, Dodge,

Ram, FIAT®, or Alfa Romeo vehicles.*

• Easy access to vehicle information

anywhere you go using categories, book-

marks, search and an A-Z index.

20_JL_QRG_EN_USC_t.book Page 18

Page is loading ...

Jeep 2020 Wrangler Reference guide

Brand: Jeep

Model: 2020 Wrangler

Category: Cars

Type: Reference guide

This manual is also suitable for

Wrangler

Download PDF

report

Jeep 2020 Wrangler Reference guide

This manual is also suitable for

Jeep 2020 Wrangler Reference guide

Related papers

Other documents