DaytonAudio ME620C User manual

DaytonAudio
Brand
DaytonAudio
Model
ME620C
Type
User manual

This manual is also suitable for

One speaker is playing while the other is not:
● Check the balance control on the receiver. Make sure it is centered.
●
Loose connection at either the receiver or the speaker. Double check connections.
● Bad speaker cable. Replace suspect speaker cable.
Receiver cuts on and off:
● This could be caused by a short circuit between the positive and negative leads.
Check the connections at the back of the receiver, and then at the speaker; make
sure that no strands of wire from one connector are touching the other connector.
10) Caring For Your Ceiling Speakers
The two most common ways that ceiling speakers are permanently damaged:
1) Not enough power at higher volumes.
2) Too much power at higher volumes.
Contrary to conventional wisdom, far more speakers are damaged as a result of under-powering,
than by overpowering. When a receiver runs out of power, it still tries to reproduce the musical
signal by “clipping” the waveform. At high volume levels this clipping introduces gross amounts of
distortion to the speaker, eventually destroying it. If the sound from your ceiling speakers starts to
sound distorted, turn down the volume.
Having plenty of reserve power will help your speakers reproduce dynamic contrasts and quick
transients of music much more effectively, but you do have to exercise good judgment; too much
power will also permanently damage a speaker. Again, if you hear distortion, turn the volume down.
Model number ME650C ME620C ME820C
Woofer 6.5" Kevlar cone 6.5" Kevlar cone 8" Kevlar cone
Tweeter 1" Silk Pivoting 1" Silk 1" Silk
Frequency response (Hz) 50-20,000 45-20,000 30-20,000
Dimensions H x W x D (in) 9-7/8" dia x 5-5/8" 9-1/4" dia x 3-5/8" 11" dia x 3-7/8"
Cut-out size H x W (in) 8-1/4" dia. 8-1/4" dia. 10" dia.
Power handling (RMS/Peak) 35/70 35/70 45/90
Impedance 8 8 8
SPL (1W/1m) 88 ±3dB 89 ±3dB 89 ±3dB
Xover point (Hz) 3,000 3,000 3,000
Xover slope 12dB/octave 12dB/octave 12dB/octave
Tweeter attenuation (dB) NA NA NA
Type 15° Coaxial Coaxial Coaxial
Specifi cations
Warranty Information
Dayton Audio products are warranted free from defects in material and workmanship for 5 years
from date of purchase. 1 year warranty applies to the following products: powered subwoofers and
electronic devices (e.g. subwoofer amplifi ers, and plate amplifi ers, as well as the Omnimic V2 and
DATS loudspeaker testing devices). In the rare case of a product failure, please contact your place
of purchase or call our Customer Support Department at (937) 743-8248.
Warranty Limitations
There are no other warranties, either expressed or implied, that extend the foregoing, and there
are no warranties of merchantability or fi tness for any particular purpose. Dayton Audio is not
responsible for any consequential or inconsequential damage to any other unit or component or the
cost for installation or extraction of any component of the audio system, or for the improper use of
products. This includes but is not limited to burnt voice coils, overheating, bent frames, holes in the
cone, or broken lead wires.
This warranty gives you specifi c legal rights and you may also have other rights that vary from state
to state.
Non-Warranty Service: If non-warranty service is required, the product may be sent to the
Company for repair/replacement, transportation prepaid, by calling (937) 743-8248 for details,
complete instructions, and service fee charges.
Dayton Audio
®
Last Revised: 4/2/2015
daytonaudio.com
tel + 937.743.8248
info@daytonaudio.com
705 Pleasant Valley Dr.
Springboro, OH 45066
USA
Ceiling Speaker
Models: ME650C / ME620C /
ME820C
User Manual
Congratulations on the purchase of your Dayton Audio
®
Micro-Edge™ Ceiling Speakers. These
speakers were manufactured with high quality components and engineered to deliver top quality
sound performance.
● Contemporary Micro-Edge design
● Long-throw woven Kevlar
®
woofers with rubber surround
● Coaxially mounted 1" silk dome tweeter (Pivoting on ME650C)
● 12 dB/octave optimized crossover
● 15° mounting angle provides cinematic imaging (ME650C only)
● All Dayton Audio Micro-Edge Series speakers are timbre matched to provide the best home
theater experience.
Please read these instructions completely before you begin your installation.
1) Parts Inventory
Your speaker kit should include the following:
● 1 pair of Dayton Audio Micro-Edge Ceiling Speakers with Grills
● 1 speaker installation / paint masking template
2) Installation Tools
The Dayton Audio speakers can be installed with the following simple tools:
● Pencil ● #2 Phillips screwdriver
● Masking tape ● Wire cutters & wire stripper/crimp tool
● Drill & drill bits ● Stud finder**
● Utility knife or wallboard saw*
* Recommended for use if installing in plaster walls.
** Optional tools to make the installation easier.
3) Speaker Location
To achieve the best performance from your Dayton Audio speakers, it is important to carefully
select the location for installation. Your ceiling speakers should be installed 5 to 8 feet apart to
ensure proper stereo imaging. Mount each speaker the same distance from the intersecting
walls to maintain a uniform look. Keep the speakers at least 2 feet away from the corners of
the room to avoid overemphasized bass reproduction.
Note: When installing an ME650C LCRS Ceiling
Speaker, rotate the speaker housing so that the built-in
15 degree angled loudspeaker is pointed to the center
of the listening area. The location and position of the
speaker mount can best be determined by consulting
the room layout and speaker setup guide that ac
-
companied your audio equipment. Once the ME650C
LCRS Ceiling Speaker is mounted in place, adjust the
speaker’s pivoting tweeter for best listening results.
4) Speaker Installation
Once you have selected the location for your speakers, you are ready to install them.
CAUTION: Be certain that there are no electrical wires, water pipes, or heating ducts
in the planned installation area before you start drilling or cutting into the ceiling. If
there is an electrical outlet nearby, turn off the circuit breaker to avoid possible injury.
Ceiling speakers are designed to be mounted in the ceiling between the joists or trusses.
Once you have selected the location, check to be sure you are between the joists or truss.
One method is to tap on the ceiling, you will hear a hollow sound when between two joists or
trusses and a sharper, more solid sound when right on top of, or close to a joist or truss.
An easier, more accurate method for finding the location of joists or trusses is to use a stud finder.
The Micro-Edge Ceiling speakers include a two-part template. Remove the center circle
from the template, this is a paint masking template to use if you choose to paint the speaker
frames and grill. The outer ring is used to mark the cut-out for the speakers.
Once you have established that your chosen location is be-
tween two joists or trusses, and that there are no obstructions
in the ceiling, tape your speaker template to the ceiling and
lightly trace around the inside edge with a pencil and drill a 1"
hole in the center of the template outline. Next, use a piece of
stiff wire (a coat hanger works well), bend it 8" from the end at
a 90 degree angle. Insert the bent part of the coat hanger into
the 1" hole and rotate the wire in a complete circle to check for
obstructions. If the wire hits a stud on either side, reposition
your template to the left or right and mark the outline again.
Keep the pilot hole within the template outline.
If the ceiling is made of drywall, simply cut the marked area with
your utility knife or drywall saw. If the ceiling is made of plaster,
you should use a saw with a higher tooth count to reduce the
chance of breaking the plaster. Test fit the speaker in the hole, the
speaker should fit loosely and the speaker frame should cover the
edges of the hole. Repeat these steps for the other speaker.
5) Speaker Cable
Don’t compromise sound quality by using thin, inexpensive
speaker wire. We recommend using a high quality oxygen free
copper speaker cable. For runs less than 50 feet, we recommend
16 gauge cable, and for longer runs we recommend 14 gauge
or larger cable. Most municipalities require the use of CL2 rated
speaker cable for installation in walls and ceilings. Leave enough
speaker cable so you can stand comfortably on the floor or ladder
while connecting the speaker cable to the speakers.
6) Speaker Connection
Remove about 8" of the cable jacket to expose the inner conduc-
tors. Strip 1/4" of insulation from each conductor and connect to
the speaker terminals. When connecting the wires to the speakers, be sure to observe proper
polarity. Most CL2 rated speaker cable will have red and black conductors so you will connect
the red wire to the red speaker terminal and the black wire to the black speaker terminal.
7) Final Installation
To install the speakers into the ceiling, remove the grills
using a small paper clip, this will give you access to the
mounting screws. Turn the mounting clamps so they are
positioned as in the illustration, this will allow the speakers
to clear the hole for installation. Insert the speaker into the
hole, and tighten the mounting screws. As you turn each
screw, the mounting clamps will rotate outward to engage
ceiling material.
CAUTION: Do not over-tighten the clamps. Too much torque may snap off the lug and the
speaker will not seat securely. A snug fit is all that is necessary to assure proper performance.
8) Painting Speakers
If you choose to paint the speaker grill and/or frame we have provided a “Paint Masking Tem-
plate” to cover the woofer/tweeter assembly and help prevent possible damage. Do not try to
paint the frame and grill assembly together, the grill should always be painted separately.
Do not apply heavy coats of paint that might block the perforations in the grill.
9) Troubleshooting
Should your speakers not work properly, check the following:
No sound from speakers:
● Most stereo receivers have an A/B speaker selector switch. Make certain that
this switch is in the proper position.
● Mute feature is activated.
  • Page 1 1
  • Page 2 2

DaytonAudio ME620C User manual

DaytonAudio
Brand
DaytonAudio
Model
ME620C
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents