Zephyr ZRC-9000 User manual

Zephyr
Brand
Zephyr
Model
ZRC-9000
Category
Car kits
Type
User manual

This manual is also suitable for

Zephyr ZRC-9000 is a recirculating kit designed to be used with AK9028AS and AK9034AS. The kit includes a return air vent, return air vent screws, a charcoal filter, and charcoal filter brackets. The charcoal filter is meant to be replaced after 3-4 months of use. The return air vent can be installed at the top of the cabinet or in a soffit or ceiling. The kit also includes instructions on how to install the return air vent.

Zephyr ZRC-9000 is a recirculating kit designed to be used with AK9028AS and AK9034AS. The kit includes a return air vent, return air vent screws, a charcoal filter, and charcoal filter brackets. The charcoal filter is meant to be replaced after 3-4 months of use. The return air vent can be installed at the top of the cabinet or in a soffit or ceiling. The kit also includes instructions on how to install the return air vent.

ZRC-9000 Recirculating Kit Instructions
For Use With AK9028AS and AK9034AS
1. Remove baffle filter from insert and position
it back-side up so the mesh is visible.
3. Place filter brackets over charcoal filter and
secure in place by tucking each end of
the bracket under the baffle filter frame.
Re-install baffle filter into insert.
NOTE: Take care when installing the filter brackets as they may have sharp edges
2. Place charcoal filter on back-side of baffle
filter so it fully covers the mesh.
THIS KIT INCLUDES:
1
(1) return air vent (1) charcoal filter (3) charcoal filter
brackets.
(4) return air
vent screws
Turn to next page for instructions
on installing return air vent.
WARNING: Charcoal filter is not
meant to be washed and must be
replaced after 3 - 4 months of use.
Replacement Part: Z0F-C090
JAN12.0101 www.zephyronline.com | 1.888.880.8368
fra me
mesh
2
Install return air vent to top of the cabinet:
OPTION 1:
OPTION 2:
(for installations where cabinet does not extend to the ceiling)
Return Air Vent
Return Air Vent
6” round
duct from
AK9028AS
AK9034AS
top of cabinet
FIG.1
FIG.2
FIG.3
airflow airflow
top of cabinet
soffit or
ceiling
screw
(1 in each corner
of return air vent)
1. Cut a 6-1/2” round opening in top of the
cabinet where the ducting will connect
to the return air vent. FIG.1
2. Connect 6” round ducting from AK9028AS/AK9034AS
to return air vent collar. Return air vent collar will go
around the ducting. Secure with duct tape.
3. Secure return air vent to top of cabinet with
(4) screws.
Install return air vent to a soffit or ceiling:
(for installations where top of cabinet is flush with the ceiling)
1. Cut a 6-1/2” round opening in soffit or ceiling
where the ducting will connect to the return
air vent. FIG.2
return air vent collar. Return air vent collar will go
around the ducting. Secure with duct tape.
3. Secure return air vent to soffit or ceiling with
(4) screws.
Note: Return air vent deflectors should face
the sides to properly direct the air. FIG.3
screw (1 in each corner
of return air vent)
ZRC-9000 Recirculating Kit Instructions
For Use With AK9028AS and AK9034AS
www.zephyronline.com | 1.888.880.8368
2. Connect 6” round ducting from
AK9028AS/AK9034AS
  • Page 1 1
  • Page 2 2

Zephyr ZRC-9000 User manual

Zephyr
Brand
Zephyr
Model
ZRC-9000
Category
Car kits
Type
User manual
This manual is also suitable for

Zephyr ZRC-9000 is a recirculating kit designed to be used with AK9028AS and AK9034AS. The kit includes a return air vent, return air vent screws, a charcoal filter, and charcoal filter brackets. The charcoal filter is meant to be replaced after 3-4 months of use. The return air vent can be installed at the top of the cabinet or in a soffit or ceiling. The kit also includes instructions on how to install the return air vent.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents