IMG STAGELINE 38.8080 User manual

Brand: IMG STAGELINE

Model: 38.8080

Category: Stroboscopes & disco lights

Type: User manual

ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS

COB LED Spotlight

PARC-100E/RGB

Order No. 38.8080

INSTRUCTION MANUAL

Section 1. Getting Started

Unpacking

Safety Instructions

Unpacking

•1pc fixture (lamp installed)

•1pc User Manual

Thanks for using our PARC-100E/RGB. Carefully unpack the box and check the contents to

ensure that all parts are present and in good conditions. If anything damaged during transit,

notify the shipper immediately and keep the packing material for inspection.

Again, please save the carton and all packing materials. If the fixture must be returned to

manufacturer, it is important that the fixture be returned in the original manufacturer box and

packing.

Contents

Section 1. Getting Started

Unpacking

Safety Instructions

Section 2. Set Up

Installation

Controlling Board

Machine Connection

Section 3. Troubleshooting

Troubleshooting

Section 4. Reference

DMX Protocol

Specifications

Caution!

There are no user serviceable parts inside the unit. Do not open the housing or attempt any

repairs yourself. If exceptional problem happen, please contact related after-sale department

or manufacturer.

Any damage that cased by violating this manual is out of insurance, our company will not take

the responsibility.

Section 2. Set Up

Installation

Controlling Board

Machine connection

Installation

 This machine should be mounted through the screw holes of truss. Safety wire is a must

to fix fixture well. Make sure truss and safety wire have strong load capacity to bear 3 times

weight than fixture at least.

 This machine should be installed by qualified technician.

Safety Instructions

Please conserve this manual as operation guidance. If you sell this product to other user,

please make sure that they also receive this user manual.

Always make sure that you are connecting to the proper voltage and the line voltage not

higher than stated on the decal or rear panel of the fixture.

This lighting is intended to indoor use only. To prevent risk of fire or shock, do not expose

fixture to rain or moisture. Make sure there are no flammable, explosive or corrosive

materials surrounded in 0.5meters while operating.

The unit must be installed in a location with adequate ventilation, at least 1m away from

adjacent surfaces. Be sure that no ventilation slots are blocked.

Fixture may carry high heat, do not aim at objective exceeding 2 minutes.

Safe wire should be used to install machine. Bearing of safe wire should be 3 times of the

machine weight.

Always disconnect from the power source before servicing or replacing fuse/lamp and be

sure to replace with same fuse/lamp size and type. Cut off power before moving, repairing

and cleaning the machine.

To avoid electric shock, all fixtures must be connected to circuits with a suitable ground.

Always secure fixture using a safety chain and carrying handles. Never carry the fixture by

its cord.

Do not operate at ambient temperatures higher than 40°C (104°F).

In case of failure or misfunction occurred, stop using the unit immediately. Never try to

repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or

malfunction. Please contact the nearest authorized technical assistance center. Buy the

same spare parts/components from manufacturer directly.

Make sure the power cord is never crimped or damaged.

Avoid direct eye exposure to the light source while it is on.

Do not power on and power off the fixture in a short time.

When use DMX controller, please make sure that there is no interference sources (e.g.

intercom, high frequency radio waves and radiation source.

For your safe，please read this user manual carefully before turn on

the fixture. This machine should be operated by qualified engineer！

Machine Connection

Cables must have a male XLR connector on one end and a female XLR connector on the

other end.

A word on termination: DMX is a resilient communication protocol,

however errors still occasionally occur. Termination reduces signal errors, and therefore best

practices include use of a terninator in all circumstances. If you are experiencing problems

with erratic fixture behavior, especially over long signal cable runs, a terminator may help

improve performance.

To build your own DMX Terminator: Obtain a 120-ohm, 1/4-watt

resistor, and wire it between pins 2&3 of the last fixture. They are also readily available from

specialty retailers.

Complimentary signal cable can transmits signals to 20 unit

fixtures at most. Signal amplifier is a must to connect more fixtures

and must weld a 120-ohm, 1/4-watt resistor, and wire it between

pins 2&3 of the last fixture

5 6

Controlling Board

The display is blackout automatically if there is no any operation within 30 seconds;

Press Enter and hold for 5 seconds to show light current operating temperature;

Press MENU and hold for 5 seconds to lock KEY; Press MENU and hold for 5 seconds to

unlock KEY.

Button

Switch menu level / to return the higher

menu level

UP Scroll upwards

DOWN Scroll downwards

ENTER Confirm and save a setting

7 8

Section 4. Reference

Control Menu

DMX protocol

Specifications

Control Menu

addr：DMX

chnd：DMX

red：

gree：

colo：

address value

channel model

Red dimmer

Green dimmer

blue：

Blue dimmer

25 preset colors

Section 3. Troubleshooting

Troubleshooting

Problem Probable cause(s) Remedy

No response from

fixture when power

is applies

No power to fixture Check power cables

Fixture resets but

does not respond

correctly to

controller(DMX

mode operation)

Controller not

connected Connect controller

Incorrect

addressing of the

fixtures

Check address setting on fixture and controller

Bad data link

connection

Inspect cables and correct poor connections

and/or broken cables.

Conflict between

tracking and vector

control

Eliminate scene cross-fade on controller

Data link not

terminated Insert termination plug in output of last fixture

Defective fixture or

2 devices

transmitting on link

Bypass fixtures one at a time until normal

operation is regained:unplug both connectors

and connect them directly together

Colors cannot be

mixed

Random color

mixing is on Turn off random color mixing

Fixture does not

reset correctly

Electronic or

mechanical failure Contact service technician

910

Comment 1: when LED lamp temperature is over 58℃,the detective fan starts working; when

LED lamp temperature decrease to 45℃again , the detective fan stop working.

Comment 2: Power limiter system is independent with detective fan working system.

DMX Protocol: 10CH

Channel Function Effect

1 Dimmer 0-255: RGBW linear dimmer, from dark to light

2 R dimmer 0-255: Red linear dimmer, from dark to light

3 G dimmer 0-255: Green linear dimmer, from dark to light

4 B dimmer 0-255: Blue linear dimmer, from dark to light

5 Strobe

0-1: No applicable;

2-255: strobe speed, from slow to fast

6 Color Mixing

0-1: No applicable

2-43: Red from dark to light

44-85: Red from light to dark, Green from dark to light,

86-127: Green from light to dark, Blue from dark to light;

128-169: Red from dark to light, Blue fully light on

170-211: Red fully light on, Green from dark to light,

Blue fully light on;

212-255: Red, Green, Blue all light on fully

7 Preset color

0-5:N/A

6-15: Red 16-25: Green 26-35: Blue

36-45:lemon-green 46-55:olivine 56-65:yellow

66-75:congo-red 76-85:light-orange 86-95:rose-red

96-105:pink 106-115:soft-lilac 116-125:light-purple

126-135:powder-blue 136-145:light-blue

146-155:skyblue 156-165:light-cerulean

166-175:cyan 176-185:aqua-green

216-225:white3

186-195:light-green 196-205:white1 206-215:white2

226-235:white4 236-245:white5

fade：

temp：on

off

flas：

flash, 01-99 speed ajusting

color fade, 01-99 speed adjusting

snap：

color skip, 01-99 speed adjusting

soun：

sound active, 01-99 speed adjusting

power limitation on

power limitation off

dim：

5 dimmer curve modes

defa：

ffactory default reset

Comment:

1, Display will black out if without any operation within 30 seconds,

2, Press “ENTER” and keep it for 5 seconds, display will show temperature

3, Press “ENTER” and keep it for 5 seconds to lock keypads.

Press “ENTER” again and keep it for 5 seconds to unlock keypads.

11 12

Dimmer Curve：

5 dimmer curves are available to call up.

Ramp Effect Menu Tup(ms) Tdown(ms)

Standard Dimmer

Curve

dr-0 0 0

Dimmer Curve 1 dr-1 980 1010

Dimmer Curve 2 dr-2 1210 1320

Dimmer Curve 3 dr-3 1600 1710

Dimmer Curve 4 dr-4 1850 1980

Master and slave: Set up one fixture as Master fixture (triggering), other fixtures as slave

fixtures (receiving trigger signals), when connect the signal cable, the slave fixtures will run

and keep function synchronism as master fixtures.

Control more machines: Set up all fixtures d10-- or d.5—Menu, set all fixtures same

addresses value or subject to DMX console performance (Attention: all fixtures use the same

DMX channel 10 or 5CH).

246-255:white 6

Auto/

Sound

0-10:N/A;11-40: Color fade; 41-70: red, green, blue fade

1; 71-100: yellow, cyan, purple fade 2; 101-130: color

jump; 131-160: red, green, blue jump; 161-190: yellow,

cyan, purple jump; 191-220: sound color strobe;

221-255: sound color jump

9 Auto speed 0-255: auto speed adjust, from slow to fast

Dimmer Curve/

Power Limiter

0-20: standard dimm er curve

21-40: dimmer curve 1

41-60: dimmer curve 2

61-80: dimmer curve 3

81-100: dimmer curve 4

101-149: N/A

150-155: (3 second interval) power limiter off;

156-199: N/A

200-205: (3 second interval) power limiter on

206-255: N/A

Comment: When LED lamp temperature increase to 80°C, the Max. power consumption

will be 50%;When LED lamp temperature decrease to 58°C, the Max. power consumption

will be 100% ;

DMX Protocol: 5CH

Channel Function Effect

1 Dimmer 0-255: RGBW linear dimmer, from dark to light

2 Red dimmer 0-255: Red linear dimmer, from dark to light

3 Green dimmer 0-255: Green linear dimmer, from dark to light

4 Blue dimmer 0-255: Blue linear dimmer, from dark to light

5 Strobe 1-255: color strobe speed, from slow to fast

Comment:

Under 5CH DMX protocol, dimmer curve is subject to Menu “dr---“, Power limiter is subject to

Menu “T---“.

Falsch 36 • 28307 Bremen • Germany

01.27.04.2017

MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany

www.monacor.com

01.15.05.2017

Specifications

Power supply:

Operating voltage:

Power consumption, operation:

Wattage:

Light source:

Strobe:

Dimmer:

Cooling:

Admiss. ambient temp.:

Beam angle

Control mode

Channels

Net weight:

Dimensions:

Connections:

~230 V/50 Hz/160 VA

~230 V

160 VA

100 W

1x 100 W RGB COB LED

0 ~ 20 Hz

5 different dimmer curves

1x temperature-controlled fan

0 - 40 °C

60° ( can be adjusted by barn door)

DMX512/Manual

10 or 5 DMX channels（switchable）

1.5kg

W150*H220*D245mm (excluding bracket)

3-pole XLR (DMX in),

3-pole XLR (DMX out)

IMG STAGELINE 38.8080 User manual

Brand: IMG STAGELINE

Model: 38.8080

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

IMG STAGELINE 38.8080 User manual

IMG STAGELINE 38.8080 User manual

Other documents