Page is loading ...
100 x 190mm
11. Use shift then "7" to access "subtitle" / "closed
caption".
12. Use shift then "9" to access "info" and to
"select" when in guide or menu mode.
13. Use shift then "8" to access the toggle function
from PIP back to normal picture.
14. Exits on screen menus, guides and returns you
to the previous on screen selection.
15. Brings up the menu screen. Use shift then ,
, , , keys to scroll, use shift then menu
to access PIP.
16. Rewind when in VCR mode, scan back when
in DVD, CD & DVR mode. Use shift then
to scroll left thru menus and guides.
17. Fast forward when in VCR mode. Scan
forward when in DVD, CD & DVR mode.
Use shift and to scroll right thru menus and
guides.
18. Access the play feature when in VCR, DVD
mode. Use shift then to scroll up through
menus and guides.
19. Stop key when in VCR, DVD, CD & DVR
mode. Use shift then to access the OK
function when scrolling through menus and
guides.
20. Pause when in VCR, DVD, CD & DVR mode.
21. Record when in VCR DVR & DVD mode.
Use the shift then to access guide when in
SAT or Cable mode.
KEY FUNCTION DESCRIPTIONS
1. Programs your VCR. Also programs one
auxiliary device using the shift key.
2. Programs your TV. Also programs one
auxiliary device using the shift key.
3. Power key- Turns device for remote's current
mode on or off.
4. Programs your satellite receiver. Also
programs one auxiliary device using the shift
key.
5. Programs your DVD player. Also programs
one auxiliary device using the shift key.
6. Allows you to program auxiliary devices 1-4
or allows you to access secondary functions of
certain devices.
7. Changes the channels when in TV, DVR,
satellite or cable mode. Scrolls through
chapters when in DVD mode or tracks when in
CD mode.
8. Changes the volume level of the device.
Normally used when in TV mode.
9. Allows you to return to the previously selected
channel in TV, Sat or Cable mode. Also allows
you to control the input source when in TV
mode. Press the shift key and the source key
to toggle.
10. Allows you to turn the volume on or off when
in TV mode.
32
100 x 190mm
Table of Contents
Product Diagram Page 1
Key Function Descriptions Page 2 - 3
Introduction/Package Contents Page 4
Getting Started Page 6
Battery Installation & Information Page 7
How to set up your La-z-boy remote Page 8 - 9
oBy code entry
oBy code search
Maintenance Page 16
Troubleshooting Page 17
Warranty Page 18
Congratulations on the purchase of your La-Z-Boy
Universal Remote Control, a state of the art product
which integrates several infra-red devices to deliver
complete A/V control at the tip of your fingers.
Before operating your remote please read through this
manual carefully and save it for future reference.
This package contains the following:
- One LZ6100 Mega Universal Remote Control.
- One Installation Guide.
- One Quick Reference Guide.
- One Infra-red Device Code List.
- A blank device sticker (To be placed on the battery
door).
La-Z-Boy has evolved throughout their 75 year history
to become America's Number 1 furniture brand.
The new line of La-Z-Boy Universal Remote Controls
represents the perfect marriage of relaxation, comfort,
ease of use, quality and convenience when watching
television in your favorite La-Z-boy!
The La-Z-Boy Difference:
- Bilingual Consumer hotline available 24 hours/day,
7 days/week.
- Easy to follow quick reference guide.
- Comfortable rubber grips.
- On-line Tutorial.
54
100 x 190mm
1. HOW TO INSTALL BATTERIES
La-z-boy recommends the use of alkaline batteries in our
remotes for longest battery expectancy. The number of
batteries required is stated on the back of the coversheet.
1. Remove the battery cover on the back of your
La-Z-Boy remote (LR).
2. Check the polarity of the batteries and the "+/-"
marks inside the battery compartment.
3. Insert the batteries.
4. Push the battery cover back in place.
Battery Low
If the indicator flashes twice slowly after using the LR, it
shows that the battery level is low. You must replace
them with new batteries to ensure proper functioning.
Note:
4 AAA batteries required (not included).
GETTING STARTED
A few helpful hints on terms used in this manual.
LR:
La-Z-Boy Universal Remote Control.
LED:
The red indicator light that flashes with an infra-red
command to your equipment.
Backlighting:
The blue backlighting on the keypad of your La-z-boy
remote. Backlighting turns on each time a key is pressed
and will turn off 8 seconds after the last key is released.
Battery Low:
If the red LED indicator flashes twice after activating
any command, it shows that the battery level is low. You
must replace the batteries with new batteries to ensure
proper functioning of your remote.
Note:
When replacing batteries you have approximately 5 mins
before your programmed codes are lost. All factory
program codes will remain in memory permanently.
Shift:
The shift key allows you to access secondary functions
th th
of the remote and to operate the 5 thru the 8 device
(AUX 1-4). Please follow the instructions in this manual.
76
100 x 190mm
Suggestion:
- If you cannot find a correct Device Code for your
equipment, refer to the section that follows:
How To Set Up The LR By Searching Through the
Library.
- For future reference it is recommended to make a
note of your Device Codes in the space provided on
the back label after setting up your LR correctly.
By Searching Through the Library
If you cannot identify a correct Device Code for your
equipment from the Device Code list, you may search
through the code library:-
1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. TV). The red
LED indicator will blink once.
3. Hold down "CHANNEL +" and "VOLUME -" on
the LR together simultaneously for 2 seconds until
the red LED indicator lights continuously.
4. Enter a corresponding Search Code from following
table. The indicator should go out immediately.
(e.g. press TV device mode key, then press
"CHANNEL +" and "VOLUME -", and enter The
TV Search Code 0001.)
5. Press the same desired device mode key again as in
step 2 above. (e.g. TV)
6. Hold down "CHANNEL +" and "VOLUME -"
together simultaneously again for 2 seconds until the
red LED indicator lights continuously. LR is ready
to start searching.
2. HOW TO SET UP YOUR LA-Z-BOY
REMOTE (LR)
By Entering Device Code
You may setup your La-Z-Boy Remote (LR) by the
following code entering instructions.
1. Turn on your device (e.g. TV).
2. Refer to the DEVICE CODE LIST; look up the 4-
digit Device Code which corresponds to the brands
of your A/V equipment. If there are more than one
Device Code listed under your brand, try from the
first code.
3. Press a desired Device Mode Key (e.g. TV). The red
LED indicator will blink once.
4. Hold down "CHANNEL +" and "VOLUME -" on
the LR simultaneously for 2 seconds until the red
LED indicator lights continuously.
5. Use the number keys 0-9 to enter your 4-digit Device
Code. The red LED indicator should go out
immediately.
Then try the function keys (e.g. TV) on the LR. If your
device (e.g. TV) responds to your activated function
correctly, you have entered the right Device Code.
Otherwise, repeat the above setup with the next available
Device Code until your device (e.g. TV) responds to
your activated function, and most keys work correctly.
* Simply repeat the above procedures to enter the
Device Codes for your VCR, SAT, DVD and other
Devices. (Remember to press a correct Device Mode
Key in step 2 above). For set up of Auxiliary devices
(AUX 1-4) press "SHIFT" followed by the desired
device key (AUX 1-4) then follow steps 4-5 above.
Note:
If the indicator flashes twice in step 5, a wrong Device
Code has been entered. You are required to repeat step 3
to 5 again.
DEVICE
TYPE:
SEARCH
CODE:
TV
0001
VCR
0002
SAT
0003
CABLE
0004
DVD
0005
AUDIO
0006
CD
0007
HOME
THEATER
0008
98
100 x 190mm
Important:
When searching through the Library for some older
devices, if the power on/off function of your device is
not infra-red controlled you need to follow steps 2 to 6
above and start searching:-
- Press " " (power) key and another important
function key alternately until your device responds
to the expected function, press the same device
mode key (e.g. TV) to lock in the code.
- Press " " (power) key & "Channel +" alternately,
or;
- Press " " (power) key & "1" alternately.
Note:
- Each time you press the " " (power) key, the LR
will skip to the next code and send out a POWER
signal trying to turn off your device.
- If you failed to stop pressing " " (power) key in
time when your device has been turned off, turn on
your device again immediately. Before the indicator
goes out, press " " on the LR to skip backward.
Repeat the step 7 above and lock in the code.
- If the red LED indicator flashes twice after you
pressed the " " (power) key, you are already at the
last code of the library.
- Besides device keys, " " (power) key and " "
(mute) key, all keys can be operated if the remote has
entered search mode.
7. Aim the LR at your device (e.g. TV); press the " "
(power) key repeatedly every 1-2 seconds until the
device has been turned off. The red LED indicator
will blink once each time you press the " " (power)
key to indicate your remote is scrolling thru the code
library. Once your device has been turned off,
immediately press the same device mode key (e.g.
TV) to lock in the search code and the red LED
indicator should go out.
* Simply repeat the above setup procedures to search
the Device Code for your VCR, SAT, DVD and other
Devices. (Remember to press a correct Device Mode
Key and correct Search Code in step 2-5 above).
* For set up of Auxiliary devices (AUX 1-4) press
"SHIFT" followed by the desired device key (AUX
1-4) then follow steps 3-7 above.
Note:
The search process can take several minutes due to the
number of codes stored in the library.
Note:
You cannot search through the code library for DVR
devices.
Important:
During set up mode, the red LED indicator will blink
twice and the set up procedure will be terminated if any
of the following conditions occur;
- No key has been pressed for more than 8 seconds.
- An invalid code number has been entered.
- An invalid key (not a numeric key) has been pressed.
1110
100 x 190mm
4. PUNCH THROUGH
You can activate certain functions like TV volume to be
operated in other modes such as SAT. This is referred to
as Punch Through please refer to the following
procedure for activating this function.
4.1 To activate the Punch through Channel setting:
4.1.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
4.1.2. Press and Hold "CHANNEL +" key.
4.1.3. Press the desired Device Mode Key in which you
want to change the channel for (e.g. SAT).
4.1.4. Release "CHANNEL +" (LED flashes once if the
setting is activated).
4.2 To deactivate the Punch through Channel
setting:
4.2.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
4.2.2. Press and Hold "CHANNEL -" key.
4.2.3. Press the Desired Mode Key in which you want to
change the channel for (e.g. SAT).
4.2.4. Release "CHANNEL -" (LED flashes twice if the
setting is deactivated).
3. OPERATING THE LA-Z-BOY
REMOTE (LR)
Normal Operation
1. Once you have setup up the LR for your A/V
equipment, it works like the original remote control.
To operate, just aim it at your equipment, press an
appropriate device mode key and invoke the desired
function by pressing a corresponding key on the LR.
The indicator flashes during signal transmission and
as confirmation of key touch.
2. Use the shift button when attempting to access
auxiliary devices (AUX 1-4) or when attempting to
access secondary functions please refer to the Key
Function Description on Page 2.
Note:
On step 4.1.3 or 4.2.3 if desired device is an
auxiliary device press (SHIFT) then the
desired Auxiliary key (AUX 1-4).
- Press "SHIFT" key before step 4.1.3 or 4.2.3,
LED will flash twice.
- Release "SHIFT" key, LED will turn ON
continuously.
- Continue Step 4.1.4 or 4.2.4.
1312
100 x 190mm
5. MACRO POWER
The Macro Power allows you to turn a second device
on or off at the same time. Follow the steps below to
activate this function.
5.1 To activate the Macro Power setting:
5.1.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
5.1.2. Press and Hold (power) key.
5.1.3. Press desired Device Mode Key (e.g. SAT).
5.1.4. Release (power) key (LED will flash once if
the setting is activated).
5.2 To deactivate the Macro Power setting:
5.2.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
5.2.2. Press and Hold (power) key.
5.2.3. Press desired SAT Device Mode Key (e.g. SAT).
5.2.4. Release (power) key (LED flashes twice if
the setting is deactivated).
" "
" "
" "
" "
4.3 To activate the Punch through Volume setting:
4.3.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
4.3.2. Press and Hold "VOLUME +"key.
4.3.3. Press desired Device Mode Key in which you
want to change the channel for (e.g. SAT).
4.3.4. Release "VOLUME +" (LED flashes once if the
setting is activated).
4.4 To deactivate the Punch through Volume
setting:
4.4.1. Press desired Device Mode Key (e.g. TV). The
red LED indicator will blink once.
4.4.2. Press and Hold "VOLUME -" key.
4.4.3. Press desired Device Mode Key in which you
want to change the channel for (e.g. SAT).
4.4.4. Release "VOLUME -" (LED flashes twice if the
setting is deactivated).
Note:
On step 4.3.3 or 4.4.3 if desired device is an
auxiliary device press (SHIFT) then the desired
Auxiliary key (AUX 1-4).
- Press "SHIFT" key before step 4.3.3 or 4.4.3,
LED will flash once.
- Release "SHIFT" key, LED will turn ON
continuously.
- Continue Step 4.3.4 or 4.4.4.
Note:
On step 5.1.3 or 5.2.3 if desired if desired device is
an auxiliary device press (SHIFT) then the desired
Auxiliary key (AUX 1-4).
- Press "SHIFT" key before step 5.1.3 or 5.2.3,
LED will flash twice.
- Release "SHIFT" key, LED will turn ON
continuously.
1514
100 x 190mm
7. TROUBLESHOOTING
Q. My LR does not work at all!
A. Check your A/V device, if the device's main switch is
turned off, your LR can not operate your device.
A. Check if your batteries are inserted properly in
correct +/- positioning.
A. Check whether you have pressed the corresponding
device mode key for your device.
A. If the battery level is low, replace the batteries
Note: When replacing the batteries, you have
approximately 5 mins before your programmed
codes are lost.
Q. If several Device Codes are listed under the brand of
my A/V device, how can I select the correct Device
Code?
A. To seek the correct Device Code for you're A/V
device, test the code one by one until most keys
work properly.
Q. My A/V equipment responds to only some of the
commands.
A. You have set a code for which only some commands
work properly but some do not. Try other codes
until most keys work properly.
Q. My combo device i.e. VCR/DVD can not be
programmed using the codes provided.
A. Try programming the devices individually i.e. first
your VCR with the VCR codes from the code list
and then the DVD with the DVD Codes from the
code list.
For help with set up call 1-888-229-1459 or visit
www.lazboyremotes.com for an on-line tutorial.
6. MAINTENANCE
- Do not expose your LR to dust, strong sunlight,
humidity, high temperature or mechanical shock.
- Do not use old and new batteries together as old
batteries tend to leak.
- Do not use corrosive or abrasive cleaners on your LR.
Keep the unit dust free by wiping it with a soft dry
cloth.
- Do not disassemble your LR, it contains no user-
serviceable parts.
1716
100 x 190mm
ECP will repair or replace the defective parts and return
them at ECP's cost by a shipping method selected by
ECP. When contacting ECP to obtain an RMA,
Purchaser may request expedited return shipping at
Purchaser's cost.
THIS WARRANTY IS NOT TRANSFERABLE, AND,
TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, IS IN LIEU OF ALL OTHER
WARRANTIES, REPRESENTATIONS AND
CONDITIONS, EXPRESS OR IMPLIED,
STATUTORY OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO OTHER PERSON OR
REPRESENTATIVE IS AUTHORIZED TO MAKE
ANY OTHER WARRANTY ON BEHALF OF ECP OR
ASSUME FOR ECP ANY OTHER LIABILITY IN
CONNECTION WITH THE SALE OF THIS
PRODUCT. IN NO EVENT WILL ECP BE LIABLE
FOR ANY DAMAGES, INCLUDING BUT NOT
LIMITED TO INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OR INABILITY TO USE THE PRODUCT,
INCLUDING DAMAGES DUE TO ECP'S
NEGLIGENCE.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE
AND COUNTRY TO COUNTRY.
La-Z-Boy is a registered trademark of La-Z-Boy
Corporation and is used
under license by:
© 2008 Elexa Consumer Products, Inc.
6200 N. Hiawatha Ave, 8th Floor
Chicago, IL 60646
One Year Limited Warranty:
Elexa Consumer Products, Inc. ("ECP") warrants to the
original retail purchaser ("Purchaser") that the La Z
TM
Boy Home Theater Series Mega Universal Remote
LZ6100 (the "Product") will be free of defects in
materials or workmanship under normal use for one (1)
year from the date of purchase (the "Warranty Period").
For the Purchaser only, if the Product fails to perform as
specified during the Warranty Period due to defective
parts or faulty workmanship, ECP will repair or replace
the defective or damaged parts of the Product. Normal
wear and tear is not covered, nor is abnormal use, misuse,
mishandling, faulty installation, improper shipping,
damage caused by disasters such as fire, flood or
earthquake, neglect, accident or tampering. This
warranty covers only normal use in the United States and
Canada.
To obtain warranty service during the Warranty Period,
contact ECP Customer Service by telephone 1-888-229-
1459 between the hours of 12am and 11:59pm, or email
[email protected] for instructions on
sending damaged parts and documentation and for a
Return Material Authorization number (RMA). Products
returned to ECP for repair or replacement without
authorization will be returned to you at your expense.
All warranty claims must be accompanied by a legible
copy of the original receipt showing date and particulars
of purchase. The RMA number must be clearly written
on the side of the shipping container in which you return
the Product or defective parts. Unless otherwise
instructed by us, the Product must be sent freight prepaid
to the following address:
Elexa Consumer Products, 6200 N. Hiawatha Ave,
Chicago IL 60646
F820-7330-0000
Back
1918
/
