Source Pro Industries 2AFOO-SP2618FPBT User manual

Brand: Source Pro Industries

Model: 2AFOO-SP2618FPBT

Category: Fireplaces

Type: User manual

This manual is also suitable for

SP2618-HE-FGPBBT

INSTRUCTION MANUAL ENCLOSED

IMPORTANT

Please note when you open the carton carefully check the unit and make sure there is no damage. If you

have any problem with assembling the unit, with how the various funcons work or with damage or

missing parts. Please call# +1-844-455-4621 (9:00AM - 5:00PM EST) or email:

[email protected] immediately for service before return the unit to the store where it

was purchased.

Insert Model:

SP2618-HE-FGPBBT

ELECTRIC FIREPLACE HEATER

HOME OWNER’S INSTRUCTION MANUAL

Model: SP2618-HE-FGPBBT

ATTENTION

FIND A LOCATION FOR THE FIREPLACE HEATER THAT IS PROTECTED FROM DIRECT

SUNLIGHT.

FAILURE TO READ ALL INSTRUCTIONS MAY RESULT IN A POSSIBLE ELECTRIC SHOCK, FIRE

HAZARD AND / OR INJURY WILL VOID THE WARRANTY

CONSUMER SAFETY INFORMATION

PLEASE READ THIS MANUAL BEFORE INSTALLING AND OPERATING THIS APPLIANCE

WARNING

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY AN ELECTRIC SHOCK

OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE

VICINITY OF THIS OR ANY OTHER APPLIANCE.

Thank you and congratulaons on your purchase of a Source Pro ﬁreplace. Please read

the installaon & operang instrucons before using this appliance.

ATTENTION

Also Requires-

Wood Fireplace Mantel

SAFETY INFORMATION

IMPORTANT INSTRUCTIONS

Please read and understand this enre manual before aempng to assemble, operate or install the product.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instrucons, may cause harmful interference to radio communicaons.

However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause

harmful interference to radio or television recepon, which can be determined by turning the equipment oﬀ and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separaon between the equipment and the receiver

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada Licence-exempt RSS-210. Operaon is subject to the following two condions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operaon of the device.

CAUTION: To maintain compliance with the RF exposure guidelines, place the base unit at least 20cm from nearby persons.

WARNING: Changes or modiﬁcaons to this unit not expressly approved by party responsible for compliance could void the

user’s authority to operate the equipment.

WARNING: Extreme cauon is necessary when any heater is used by or near children or individuals with

disabilies and whenever the ﬁreplace is le operang and unaended.

WARNING: DO NOT run cord under carpeng. DO NOT cover cord with throw rugs, runners, or similar

covering.Do not route cord under furniture or appliances. Arrange cord away from traﬃc areas and where it

will not be tripped over.

WARNING: Do NOT insert or allow foreign objects to enter any venlaon or exhaust opening as this may

cause an electric shock or ﬁre, or damage the appliance.

WARNING: This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline,

paint or ﬂammable vapors or liquids are used or stored. This ﬁreplace should not be used as a drying rack for

clothing. Christmas stockings or decoraons should not be hung in the area of it.

WARNING: This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep

combusble material, such as furniture, pillows, bedding, papers, clothes and curtains, at least 3 feet from

the front of the heater and keep them away from the side and rear.

When using electrical appliances, basic precauons should always be followed to reduce the risk of ﬁre, electric

shock and injury to persons, including the following:

Read all instrucons before installing or using the heater.

DANGER: If the informaon in this manual is not followed exactly, an electric shock or ﬁre may result causing

property damage, personal injury or loss of life.

SAFETY INFORMATION

Use this appliance only as described in the manual. Any other use is NOT recommended by the manufacturer and

may cause ﬁre, electric shock or injury to persons.

CAUTION

• If possible, ALWAYS unplug this appliance when not in use.

• DO NOT operate any heater with a damaged cord or plug or aer the heater malfuncons.

• DO NOT operate any heater if it has been dropped or damaged in any manner. Disconnect power at service

panel and have heater inspected by a reputable electrician before reusing.

• Any repairs to this ﬁreplace should be carried out by a qualiﬁed service person.

• Under no circumstances should this ﬁreplace be modiﬁed. Parts having to be removed for servicing must be

replaced prior to operang this ﬁreplace again.

• DO NOT use outdoors.

• This heater is not intended for use in bathrooms, laundry areas and similar indoor locaons. NEVER place heater

where it may fall into a bathtub or other water container.

• To disconnect this appliance, turn controls to the oﬀ posion, then remove plug from outlet.

• ONLY connect to properly grounded outlets.

• This appliance, when installed, must be electrically grounded in accordance with local codes, with the current

CSA C22.1 Canadian Electrical Code or follow the Naonal Electrical Code, ANSI/NFPA N0.70.

• To prevent a possible ﬁre, DO NOT block air intakes or exhaust in any manner. DO NOT use on so surfaces, like

a bed, where opening may become blocked.

• The heaters MUST NOT be located immediately below a socket-outlet.

• ALWAYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable

power tap (outlet/power strip).

• There is a thermostat protecve device provide inside of unit. If the inner temperature overheats or abnormal

heang occurs, the thermostat protecve device will cut oﬀ power supply to prevent damage or risk of ﬁre.

• DO NOT slide insert on top of wood to avoid scratching wood surface.

• DO NOT place any objects on top of insert and top air intake vents as this will cause unit to overheat and can

cause a ﬁre.

Electrical Connecon

A 15-amp, 120-volt, 60 Hz circuit with a properly grounded outlet is

required. Preferably, the ﬁreplace will be on a dedicated circuit as other

appliances on the same circuit may cause the circuit breaker to trip or

the fuse to blow when the heater is in operaon. The unit comes

standard with 6-. three-wire cord, exing from the rear of the

ﬁreplace. DO NOT exceed the current rang of the current tap. ALWAYS

plug heaters directly into a wall outlet/receptacle. NEVER use with an

extension cord or relocatable power tap (outlet/power strip).

•

This heater is for use on 120 volts. The cord has a plug as shown

below. See illustraon for grounding instrucon. An adapter as shown

at C is available for connecng three-blade grounding type plugs to

two-slot receptacles. The green grounding lug extending from the

adapter must be connected to a permanent ground such as a properly

grounded outlet box. The adapter should not be used if a three-slot

grounded receptacle is available.

•

Voltage: 120 VAC, 60 Hz

Amps: 11.7 Amps

Was: 1400 Was

ELECTRICAL SPECIFICATIONS

Grounding Pin

Metal

Screw

Cover of

Grounding

Box

Grounding Pin

Grounding Means

Adapter

SAVE THESE INSTRUCTIONS

1. Posion your completed mantel close to its ﬁnal locaon. Make sure you can access the back of the mantel as

your electric ﬁreplace insert will be install from the back.

2. Place a piece of cardboard or protecve sheet on the ﬂoor in order to avoid scratching the decorave surface of

your mantel during assembly. Please DO NOT fully ghten the KD screws unl all panels are assembled.

3. The ﬁreplace insert can be installed aer the mantel has been fully assembled.

WARNING: Make sure the ﬁreplace insert controls are in the OFF posion and the unit is NOT plugged in.

CAUTION - High temperature, risk of ﬁre, keep electrical cords, drapery, furnishings, and other combusbles at

least 3 feet (0.9 m) from the front of the heater and away from the side and rear.

To reduce the risk of ﬁre, do not store or use gasoline or other ﬂammable vapors and liquids in the vicinity of the

heater.

INSTALLATION INSTRUCTION

INSTALLATION

Rear view of fireplace

ELECTRIC

REPLACE

INSERT

OPERATING INSTRUCTIONS

Mode Buon

Power Buon

• Pressing the power buon will turn ON or OFF the unit.

• When the unit is in ON mode, the power icon indicator light will be shown green.

• When the unit is in OFF mode, the power icon indicator light will be shown red. When power OFF, unit will be

stopped, if heater is working before power OFF the unit, fan will have 20 seconds delay to ensure heat will not

be trapped inside the unit.

Note: When plug the unit each me, 5 seconds fan and heater will turn on for internal check program.

Note: The unit has a memory funcon with last sengs for heang level and ﬂame brightness eﬀect, unless the

main power to the unit has been interrupted.

Temperature Seng

• The temperature mode controls the heater’s thermostat seng.

• Press UP Arrow Buon or Down Arrow Buon to scroll through the pre-set temperature range from 59°F (15°C)

to 86°F (30°C), ON & OF (OFF).

• Hold the mode buon for 3s, this allows the temperature unit changing from °C to °F or °F to °C. The unit

default is °F.

Note: This funcon is only available if using the control panel.

• When the ambient temperature is higher than the set temperature, heater will turn oﬀ automacally.

• Press the mode buon to cycle through the diﬀerent funcons. Each me the mode buon is pressed, the

mode will enter the next funcon - Temperature, Timer or Flame Brightness.

Timer Seng

• The mer seng shoud be used to set the countdown for the unit’s main power.

• Press Up Arrow Buon or Down Arrow Buon to adjust the mer seng from 0 hour (OFF) to 9 hours with 0.5

hour interval.

Flame Brightness Seng

• The ﬂame brightness mode should be used to set the ﬂame brightness.

• Use Up arrow buon or Down arrow buon to scroll through the ﬂame brightness sengs:

F0 (Flame OFF, only lowest brightest on ember bed), F1, F2, F3, F4, F5 (brightest).

Note: Heater must be properly installed before it is used.

OPERATING INSTRUCTIONS

Flame Color Seng

• The ﬂame brightness mode should be used to set the ﬂame brightness.

• Use Up arrow buon or Down arrow buon to scroll through the ﬂame brightness sengs:

C1, C2, C3, C4

FIREPLACE REMOTE APP

1. Go to Apple Store or Google Play Store

2. Type “Fireplace remote” on the search bar

3. Click “download”

4. Enter your account and password if necessary

5. Installaon will be completed automacally

DOWNLOAD THE FIREPLACE MOBILE APP

Child Lock

Acvate Child Lock

When the unit is ON, holding the POWER buon for 10 seconds to acvate the Child Lock funcon. E3 will be

displayed and "Beep Sound" for 3 mes that indicate the Child Lock funcon acvate. All funcon keys are

locked. When pressing any buon, E3 will be displayed that indicate the Child Lock funcon acvate.

Inacvate Child Lock

To inacvate the Child Lock funcon, holding the POWER buon for 10 seconds.

Note: Child lock funcon is only available if using the control panel.

Manually Reset

Unplug unit, wait 5-10 minutes, then the sensor will reset itself.

UP Arrow Buon

• Use up arrow buon to increase the seng of the selected funcon.

Down Arrow Buon

• Use down arrow buon to decrease the seng of the selected funcon.

Bold Flame Fireplace Remote

Free Fireplace remote App gives you full

access and control of your ﬁreplace

QR Code for download - FREE

ColorSeng

Yellow

Blue

Yellow + Blue

Auto Change

(Fade In / Fade Out)

Color

Seng

7. Return to main page by clicking the side menu buon

8. Make sure the right corner buon is “ON” (Fig.7)

9. Adjust the color, brightness and the temperature with the Bluetooth remote

CONNECT YOUR FIREPLACE WITH FIREPLACE REMOTE

1. Turn on the ﬁreplace

2. Switch on Bluetooth on your mobile devices

3. Tap the side menu buon (Fig. 1)

4. Press “Add” (Fig. 2) buon and start searching (Fig. 3) the Fireplace nearby

5. Enter a name for the ﬁreplace (Fig. 4)

6. (Fig. 6) Blue light represents the Fireplace is connected properly and ready to use

Fig. 1 Tap the side menu buon

(Top le)

Fig. 2 Tap the ”+”buon (Top le) Fig. 3 Searching Fireplace

Fig. 4 Enter a name for the

Fireplace

Fig. 5 Connecng Fireplace Fig. 6 Fireplace Connected

FIREPLACE REMOTE APP

Connected to Fireplace

and ready to use

Fig. 8Fig. 7 Long press the name to

enter edit mode

Fig. 9 Switch oﬀ the connecon

by pressing the toggle

(top right)

CARE AND MAINTENACE

• Make sure the unit is turned OFF, unplugged and the heang elements of heater are cool whenever you are

cleaning the heater.

• Clean the heater when the heater is not in use.

• For heavy or connous use, periodic cleaning must be done more frequently.

• Clean the metal trim using a water-dampened so, clean cloth. DO NOT use brass polish or household cleaners

as these products will damage the metal trim.

• The motors used on the fan and the ﬂame generator assembly are pre-lubricated for extended bearing life and

require no further lubricaon. However, periodic cleaning/vacuuming of the fan/heater and air intake/output

vents is recommended.

• Any other servicing should be performed by an authorized service representave.

• When the heater is not in use, the heater should be stored in a dry locaon, away from possible damage. The

power cord should be stored properly to avoid contact with hot or sharp objects.

WARNING: Make sure the power is turned oﬀ before proceeding. Any electrical repairs or rewiring of

this unit should be carried out by a licensed electrician in accordance with naonal and local codes.

If repairing or replacing and electrical component or wiring, the original wire roung, color coding and

securing locaons must be followed.

WARNING: Electrical outlet wiring must comply with local building codes and other applicable

regulaons to reduce the risk of ﬁre, electrical shock and injury to persons.

WARNING: Do not use this ﬁreplace if any part of it has been under water. Immediately call a qualiﬁed

service technician to inspect te ﬁreplace and replace any part of the electrical system.

WARNING: Disconnect power before aempng any maintenance or cleaning to reduce the risk of ﬁre,

electrical shock or personal injury.

WARNING: During any service of this appliance, the power to the unit must be turned oﬀ. First turn the

main power switch to the “OFF” posion. Then remove the electrical plug from the wall outlet.

CARE AND MAINTENACE

Replacing the Remote Control Battery

When the remote control stops operang or its range seems reduced, it is me to replace the baeries.

Note: The baeries should be removed if the product is to be le unused for a long me.

Caution: Non-rechargeable baery is not to be recharged. Exhausted baery is to be removed from the

product.

1. The baery compartment is located on the back end of the remote control.

2. Press the small tab inward as you slide the baery door open and remove the old baery.

3. Insert a new CR2025 lithium baery (not included), ensuring the polaries of the baery match the inside of

the baery compartment.

4. Re-insert the baery door.

Disposal of Used Battery

A baery may contain hazardous substances that could be endangering to

environment and human health.

• This symbol marked on the baery and/or packaging indicates that used baery shall

not be treated as municipal waste. Instead it shall be le at the appropriate collecon

point for recycling.

• By ensuring the used baery is disposed of correctly, you will help prevent potenal

negave consequences for the environment and human health. The recycling of

materials will help to conserve natural resources.

For more informaon about collecon and recycling of used baeries, please contact your local municipality, your

waste disposal service or the point of sale where you purchased this item.

PROBLEM POSSIBLE CAUSE SOLUTION

TROUBLE SHOOTING GUIDE

1. No power, logs do

not glow.

1. The unit does not have power. 1. Check that unit is plugged into a standard 120

volt outlet. Then make sure power is set at “ON”

posion.

2. The overheat protecon device has

been engaged.

2. Unplug unit, wait 5-10 minutes, then the

sensor will reset itself. Plug the unit back in and

turn on the heater. If the problem persists, call

customer service.

2. E1 displayed on

control panel.

3. Unplug unit, wait 5-10 minutes, then the

sensor will reset itself. Plug the unit back in and

turn on the heater. If the problem persists, call

customer service.

3. E2 displayed on

control panel.

3. The ambient temperature sensor is

broken or not working correctly.

4. E3 displayed on

control panel.

4. Child lock funcon acvate. 4. To inacvate the Child Lock funcon, holding

the POWER buon for 10 seconds.

5. Fan motor

connues to blow

aer unit is powered

oﬀ.

5. Normal operaon. 5. This is a standard feature; the blower runs for

an addional 20 seconds to ensure heat will not

be trapped inside the unit.

6. Normal

operaon.

6. Power cord gets

warm to the touch.

6. This is normal for a heater appliance as it

requires more current to operate. Check the

connecons of the appliance cord and the outlet.

Make sure the plug ﬁts ghtly into the outlet.

During use, check the plug and outlet frequently

to determine if it is HOT; if so, disconnue use of

the appliance and consult with a qualiﬁed

electrician to check or change the overheang

outlet(s).

SOURCE PRO ELECTRIC FIREPLACE MODEL

Source Pro Industries Ltd. (hereinaer referred to collecvely as the (“company”) warrants that your new

Prokonian Electric Fireplace is free from manufacturing and materials defects for a period of one year from date of

purchase. Subject to following condions and limitaons.

1. The electric ﬁreplace must be installed and operated at all mes in accordance with the installaon and

operang instrucon furnished with the product. Any unauthorized repair, alteraon, willful abuse, accident, or

misuse of the product shall nullify this warranty.

2. This warranty is non-transferable, and is made to the original owner, provided that the purchase was made

through an authorized supplier of the company.

3. The warranty is limited to the repair or replacement of part(s) found to be defecve in material or

workmanship, provided that such part(s) have been subjected to normal condions of use and service, aer said

defect is conﬁrmed by the company’s inspecon.

4. This warranty does not cover the LED light bar included with the Prokonian Electric Fireplace.

5. The Company may, at its discreon, fully discharge all obligaons with respect to this warranty by refunding the

wholesale price of the defecve part(s).

6. Any installaon, labor construcon, transportaon, or other related costs/expenses arising from defecve

part(s), repair, replacement, or otherwise of same , will not be covered by this warranty, nor shall the Company

assume responsibility for same.

7. The owner/user assumes all other risks. If any including the risk of any direct, indirect or consequenal loss or

damage arising out of the use. Or inability to use the product, except as provided by law.

8. All other warranes – expressed of implied – with respect to the product, its components and accessories, or

any obligaons / liabilies on the part of the Company are hereby expressly excluded.

9. The Company neither assumes, nor authorizes any third party to assume, on it behalf, any other liabilies with

respect to the sale of the Prokonian product.

10. The warranes as outlined within this document do not apply to non Prokonian accessories used in

conjuncon with the installaon of this product.

11. This warranty gives you speciﬁc legal rights, and you may also have other right which vary from state to state.

This warranty is void if:

a. The ﬁreplace is subjected to prolonged periods of dampness or condensaon.

b. Any unauthorized alteraon, willful abuse, accident, or misuse of the product.

c. You do not have the original receipt of purchase.

Contact the company, at serviceprokonian@jakeglobal.com or call +1-844-455-4621 have your warranty, your

sales receipt, locaon of purchase and the model / serial number of your Source Pro products.

Email: serviceprokonian@jakeglobal.com

Call: +1-844-455-4621

1 YEAR LIMITED WARRANTY

BASIC WARRANTY

IF WARRANTY SERVICE IS NEEDED

CUSTOMER SERVICE

Please refer to part code when reordering

For questions or comments about product:

Email: [email protected] or Call: +1-844-455-4621

Crafted in China

Distributed by Source Pro Industries Ltd.

Source Pro Industries 2AFOO-SP2618FPBT User manual

Brand: Source Pro Industries

Model: 2AFOO-SP2618FPBT

Category: Fireplaces

Type: User manual

This manual is also suitable for

SP2618-HE-FGPBBT

Download PDF

report

Source Pro Industries 2AFOO-SP2618FPBT User manual

This manual is also suitable for

Source Pro Industries 2AFOO-SP2618FPBT User manual

Other documents