Bromic Heating Smart-Heat On/Off Control User guide

Bromic Heating
Brand
Bromic Heating
Model
Smart-Heat On/Off Control
Type
User guide

Bromic Heating Smart-Heat On/Off Control

The Bromic Heating Smart-Heat On/Off Control is an advanced control system that allows you to easily manage your Bromic gas heater. With this device, you can turn your heater on or off, program it to turn on or off at specific times, and adjust the heat output. The control also has a built-in safety feature that will automatically shut off the heater if it detects a problem.

Here are some of the benefits of using the Bromic Heating Smart-Heat On/Off Control:

  • Convenience: With the Smart-Heat On/Off Control, you can easily turn your heater on or off from anywhere in your home. You can also program it to turn on or off at specific times, so you can always come home to a warm and comfortable home.

Bromic Heating Smart-Heat On/Off Control

The Bromic Heating Smart-Heat On/Off Control is an advanced control system that allows you to easily manage your Bromic gas heater. With this device, you can turn your heater on or off, program it to turn on or off at specific times, and adjust the heat output. The control also has a built-in safety feature that will automatically shut off the heater if it detects a problem.

Here are some of the benefits of using the Bromic Heating Smart-Heat On/Off Control:

  • Convenience: With the Smart-Heat On/Off Control, you can easily turn your heater on or off from anywhere in your home. You can also program it to turn on or off at specific times, so you can always come home to a warm and comfortable home.
Bromic.com
Troubleshooting Guide
On/O Control Switch
Replacement Remote
Bromic On/Off Controller
• US - BH3130010-2
• AU - 2620275-1
• EU - BH3130019-1
Below are the basic steps for programming a replacement remote for
the On/O Controller.
You will need to have access to the control board inside the On/Off
Switch. If the cover is in place, you can easily remove the cover by
pressing on the top half of the cover and pushing up.
The On/Off Switch has 2 channels and you will need to program
both channels of the new remote by repeating the directions for
Channel 1 and Channel 2.
REQUIREMENTS
1. Identify the L1 and L2 toggle channel
selector and place in the L1 position:
If the ignition probes are too close to the ceramic
burners, the heater will not stay lit and the
thermocouple and igniter probe spacing will need to
be re-calibrated.
If the distance is not set properly the unit will light
but shut down after 10-15 seconds. When this
happens, the probes will need to be re-calibrated to
be approximately 1/8 inch (3.175 mm) distance from
the ceramic burners with needle nose pliers. Simply
hold the probes with a pliers and rotate them to
create the 1/8 in spacing. Please see below to identify
the probes.
Bromic.com Bromic.com
2. Programming Channel 1 of the new remote.
3. Programming Channel 2 of the new remote.
4. Test Remote
Press the MEM button 2 times and hold. There will be a continuous beep while holding the MEM button.
While holding the MEM button with one hand, press and hold the top On button on the white remote. The beep
will change to intermittent beeping and you can release both buttons.
Channel 1 is now set.
Move the channel selector into the L2 Position.
Repeat the directions from step 2 selecting the bottom On Button.
Both channels will be programmed.
If this does not resolve the issue, you will need to schedule a troubleshooting call with Bromic Tech Support.
When contacting our Tech Team we request you submit model numbers of the heaters and controls, photos of the
installed products and installation wiring along with proof of purchase to validate any warranty.
Please remember to request service calls 48 hours in advance to ensure availability.
North America - Technical Support
(800) 301-1293
www.bromic.com
Austrailia - Technical Support
1300 276 642
www.bromic.com.au
Europe - Technical Support
+31 737041029
www.bromic.co.uk
  • Page 1 1
  • Page 2 2

Bromic Heating Smart-Heat On/Off Control User guide

Bromic Heating
Brand
Bromic Heating
Model
Smart-Heat On/Off Control
Type
User guide

Bromic Heating Smart-Heat On/Off Control

The Bromic Heating Smart-Heat On/Off Control is an advanced control system that allows you to easily manage your Bromic gas heater. With this device, you can turn your heater on or off, program it to turn on or off at specific times, and adjust the heat output. The control also has a built-in safety feature that will automatically shut off the heater if it detects a problem.

Here are some of the benefits of using the Bromic Heating Smart-Heat On/Off Control:

  • Convenience: With the Smart-Heat On/Off Control, you can easily turn your heater on or off from anywhere in your home. You can also program it to turn on or off at specific times, so you can always come home to a warm and comfortable home.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents