Tool(s) required for assembly: Phillips screwdriver
5099 95-
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
C.
Side Panel
1 pc.
B.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
D.
Middle Panel
1 pc.
F.
Back Panel
3 pcs.
A.
Top
1 pc.
G.
Back Stretcher
1 pc.
H.
Back Stretcher
1 pc.
I.
Front Rail
1 pc.
K.
Base
1 pc.
M.
Door
1 pc.
L.
Door
1 pc.
Q.
Divider
1 pc.
V.
Pipe
3 pcs.
X.
Arm
1 pc.
W.
Arm Handle
2 pcs.
R.
Support
2 pcs.
S.
Rack Side
1 pc.
T.
Rack Side
1 pc.
U.
Rack Base
1 pc.
N.
Shelf
2 pcs.
O.
Shelf
2 pcs.
P.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
J1.
Back Upright
1 pc.
J2.
Back Upright
1 pc.
Hardware List
Part List
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
M6x35
Head Cap Bolt
30 pcs. (+1 extra)
M3.5x25
Wood Screw (long)
16 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
12 pcs. (+1 extra)
M4x16
Wood Screw
16 pcs. (+1 extra)
Wood Plug
7 pcs. (+2 extra)
Adjustable Pin
16 pcs. (+1 extra)
Knob
2 pcs.
Caster
2 Locking
2 Non-Locking
4 pcs.
M4x25
Machine Screw
6 pcs.
Handle
2 pcs.
ED
Head Cap Bolt
Arrow labels point to each other.
GB
I
Q
Head Cap Bolt
Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Back Stretcher (G) to
Side Panel (B) with Head Cap Bolt.
(See Figure 1)
Attach Divider (Q) to
Back Stretcher (G) with
Head Cap Bolt.
Attach Front Rail (I) to unit
with Head Cap Bolts.
Figure 1
STEP 2
Attach Back Upright (J1) to Middle Panel (D)
and Back Upright (J2) to Middle Panel (E),
then attach to unit with Head Cap Bolts.
Note: Assemble so Arrow labels
on Back Uprights (J1) and (J2)
point to each other.
J2
J1
K
Arrow label at front
Non-Locking Caster
Locking Caster
Head Cap Bolt
Wood Screw
F
C
Head Cap Bolt
Assembly Instructions 3/6
STEP 3
Slide Back Panels (F)
into position.
Attach (H) toBack Stretcher
unit with Head Cap Bolt.
Attach Side Panel (C) to
unit with Head Cap Bolts.
STEP 4
Attach Base (K) to unit with Head Cap Bolts.
Note: Arrow label indicates front of Base (K).
Attach Casters to Base (K) with Wood Screws,
with Locking Casters at front.
(See Figure 2)
H
Figure 2
F
F
STEP 5
Turn unit over to its upright position.
Attach Rack Side (T) to unit with Head Cap Bolts. (See Figure 3)
Slide Rack Base (U) and Pipes (V) into Rack Side (T).
Attach Rack Side (S) to unit with Head Cap Bolts.
Attach Arm Handles (W) to unit with Head Cap Bolts. (See Figure 4)
Slide Arm (X) into position.
Attach Supports (R) to unit with Head Cap Bolts. (See Figure 5)
Figure 5Figure 3 Figure 4
Assembly Instructions 4/6
T
SV U
R
W
Head Cap Bolt
R
W
X
Part List
Assembly Instructions 5/6
Drawer (P)
P3
P2 P4
STEP 6
Attach Drawer Front (P1) and Drawer
Back (P2) to Drawer Side (P3)
with Wood Screws (long).
Attach Drawer Side (P4) to unit
with Wood Screws (long).
Wood Screw (long)
Bottom
STEP 7
Slide Drawer Bottom (P5) into groove.
Attach Drawer Bottom (P5) to unit
with Wood Screws (short).
Roller at back Wood Screw (short)
P5
Machine Screw
Handle
P1.
Drawer Front
2 pcs.
P2.
Drawer Back
2 pcs.
P3.
Drawer Side
2 pcs.
P4.
Drawer Side
2 pcs.
P5.
Drawer Bottom
2 pcs.
STEP 8
Attach Handle with Machine Screws.
P1
Bottom
Bottom
BottomBottom
STEP 10
Cover all holes with Wood Plugs.
Figure 6 Figure 7
Wood Plug
Assembly Instructions 6/6
STEP 9
Insert Adjustable Pins into
side panels and middle panels
at desired level.
Place Shelves (N) and (O) into
position.
Attach Doors (L) and (M) to
unit by sliding door hinges into
side panel hinges. (See Figure 6)
Attach Knobs to Doors (L) and (M)
with Machine Screws.
(See Figure 7)
Attach Top (A) to unit
with Head Cap Bolts.
Slide Drawers (P) into position.
Head Cap Bolt
Knob
Machine Screw
Adjustable Pin
L
N
O
NO
P
M
A
P
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
/