Homestyles 5099-95 Assembly Instructions

Brand: Homestyles

Model: 5099-95

Type: Assembly Instructions

Tool(s) required for assembly: Phillips screwdriver

5099 95-

Kitchen Cart

IMPORTANT

Carefully remove all the parts from the carton and

place them individually on a soft cloth to prevent

scratches or other damage.

Carefully and strictly follow these assembly instructions

to ensure a completed product as designed.

Do not use power tools above 8 volts to assemble.

styles Customer Service: www.homestylesfurniture.com,home

[email protected], 888-680-7460

Side Panel

1 pc.

Side Panel

1 pc.

Middle Panel

1 pc.

Middle Panel

1 pc.

Back Panel

3 pcs.

Top

1 pc.

Back Stretcher

1 pc.

Back Stretcher

1 pc.

Front Rail

1 pc.

Base

1 pc.

Door

1 pc.

Door

1 pc.

Divider

1 pc.

Pipe

3 pcs.

Arm

1 pc.

Arm Handle

2 pcs.

Support

2 pcs.

Rack Side

1 pc.

Rack Side

1 pc.

Rack Base

1 pc.

Shelf

2 pcs.

Shelf

2 pcs.

Drawer

2 pcs.

Refer to later page(s) of these

instructions for drawer assembly.

J1.

Back Upright

1 pc.

J2.

Back Upright

1 pc.

Hardware List

Part List

Small Hex Wrench

1 pc.

Hex Wrench

1 pc.

M6x35

Head Cap Bolt

30 pcs. (+1 extra)

M3.5x25

Wood Screw (long)

16 pcs. (+1 extra)

M3.5x16

Wood Screw (short)

12 pcs. (+1 extra)

M4x16

Wood Screw

16 pcs. (+1 extra)

Wood Plug

7 pcs. (+2 extra)

Adjustable Pin

16 pcs. (+1 extra)

Knob

2 pcs.

Caster

2 Locking

2 Non-Locking

4 pcs.

M4x25

Machine Screw

6 pcs.

Handle

2 pcs.

Head Cap Bolt

Arrow labels point to each other.

Head Cap Bolt

Assembly Instructions 2/6

IMPORTANT

Use a soft cloth between these parts and the ﬂoor.

Do not use power tools above 8 volts to assemble.

Do not tighten all the bolts until each part is properly assembled.

Keep Hex Wrench as the bolts may need to be tightened in the future.

STEP 1

Attach Back Stretcher (G) to

Side Panel (B) with Head Cap Bolt.

(See Figure 1)

Attach Divider (Q) to

Back Stretcher (G) with

Head Cap Bolt.

Attach Front Rail (I) to unit

with Head Cap Bolts.

Figure 1

STEP 2

Attach Back Upright (J1) to Middle Panel (D)

and Back Upright (J2) to Middle Panel (E),

then attach to unit with Head Cap Bolts.

Note: Assemble so Arrow labels

on Back Uprights (J1) and (J2)

point to each other.

Arrow label at front

Non-Locking Caster

Locking Caster

Head Cap Bolt

Wood Screw

Head Cap Bolt

Assembly Instructions 3/6

STEP 3

Slide Back Panels (F)

into position.

Attach (H) toBack Stretcher

unit with Head Cap Bolt.

Attach Side Panel (C) to

unit with Head Cap Bolts.

STEP 4

Attach Base (K) to unit with Head Cap Bolts.

Note: Arrow label indicates front of Base (K).

Attach Casters to Base (K) with Wood Screws,

with Locking Casters at front.

(See Figure 2)

Figure 2

STEP 5

Turn unit over to its upright position.

Attach Rack Side (T) to unit with Head Cap Bolts. (See Figure 3)

Slide Rack Base (U) and Pipes (V) into Rack Side (T).

Attach Rack Side (S) to unit with Head Cap Bolts.

Attach Arm Handles (W) to unit with Head Cap Bolts. (See Figure 4)

Slide Arm (X) into position.

Attach Supports (R) to unit with Head Cap Bolts. (See Figure 5)

Figure 5Figure 3 Figure 4

Assembly Instructions 4/6

SV U

Head Cap Bolt

Part List

Assembly Instructions 5/6

Drawer (P)

P2 P4

STEP 6

Attach Drawer Front (P1) and Drawer

Back (P2) to Drawer Side (P3)

with Wood Screws (long).

Attach Drawer Side (P4) to unit

with Wood Screws (long).

Wood Screw (long)

Bottom

STEP 7

Slide Drawer Bottom (P5) into groove.

Attach Drawer Bottom (P5) to unit

with Wood Screws (short).

Roller at back Wood Screw (short)

Machine Screw

Handle

P1.

Drawer Front

2 pcs.

P2.

Drawer Back

2 pcs.

P3.

Drawer Side

2 pcs.

P4.

Drawer Side

2 pcs.

P5.

Drawer Bottom

2 pcs.

STEP 8

Attach Handle with Machine Screws.

Bottom

BottomBottom

STEP 10

Cover all holes with Wood Plugs.

Figure 6 Figure 7

Wood Plug

Assembly Instructions 6/6

STEP 9

Insert Adjustable Pins into

side panels and middle panels

at desired level.

Place Shelves (N) and (O) into

position.

Attach Doors (L) and (M) to

unit by sliding door hinges into

side panel hinges. (See Figure 6)

Attach Knobs to Doors (L) and (M)

with Machine Screws.

(See Figure 7)

Attach Top (A) to unit

with Head Cap Bolts.

Slide Drawers (P) into position.

Head Cap Bolt

Knob

Machine Screw

Adjustable Pin

NEVER

use glass cleaners on

finished furniture. Ammonia

chemically attacks the finish.

allow liquids to remain on furniture.

Absorption causes parts to warp

and split and finishes to delaminate.

NEVER

CARE INSTRUCTIONS

Do not use rubber

based placemats.

PREVENT

DISCOLORING

Do not use commercial

waxes and polishes.

PREVENT

YELLOWING

Do not place hot

objects on surface.

PREVENT

FINISH DAMAGE

Do not write

directly on surface.

PREVENT

MARKING

Do not use power tools

above 8 volts to assemble.

PREVENT

CRACKING

Do not place

in direct sunlight.

PREVENT

FADING

with a soft cloth moistened

in lukewarm soap and water.

Buff with a dry clean cloth.

CLEAN

homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.

Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,

homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor

are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.

styles Customer Service: www.homestylesfurniture.com,home

[email protected], 888-680-7460

Homestyles 5099-95 Assembly Instructions

Homestyles 5099-95 Assembly Instructions

Homestyles 5099-95 Assembly Instructions

Related papers

Other documents