IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be followed
including the following:
• Please read all instructions before using this fan.
• Use fan only for intended use as described in instruction manual.
• Install fan only in strict adherence to these instructions. Failure to do so might
create a safety hazard or result in property damage.
• To protect against electrical shock do not place fan in window, immerse fan, plug
or cord into water or with spray liquids.
• Do not hang other objects from the fan. Doing so might create a safety hazard or
result in property damage.
• Close supervision is necessary when any appliance is used by or near children.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
• Unplug from outlet when not in use, when moving fan from one location to another,
before putting on or taking off parts, cleaning.
• Unplug the fan and drape the cord up over the fan when not in use.
• Do not operate in the presence of explosive and/or flammable fumes.
• Do not place fan or any parts near an open flame, cooking or other heating
appliance.
• Do not operate with a damaged cord or plug or after the fan malfunctions, or has
been dropped or damaged in any manner.
• The use of attachments not recommended or sold by Accutek may cause hazards.
• Do not use outdoors.
• Do not let cord hang over edge of table or counter, or touch hot surfaces.
• To disconnect, grip plug and pull from wall outlet. Never yank on cord.
• Always use of dry flat surface. Do not hang or mount fan on wall or ceiling.
• Do not operate without fan grills properly in place. Avoid contacting moving parts
• This product is intended for household use ONLY and not for commercial or
industrial use.
• This fan has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Do not attempt to defeat this safety feature. Never
connect the fan to any power source other than a 120 volt alternating current
polarized outlet.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
READ AND SAVE THESE INSTRUCTIONS
Warning: To reduce the risk of fire or electrical shock, DO NOT USE THIS FAN
with any SOLID STATE Fan Speed Control Device.
- 2 -
ASSEMBLY
1.) Remove all parts from the carton:
•Motor assembly (includes the grill nut and blade knob)
•Grill set (front and rear)
•Fan blade
•Pole Assembly and Pole Nut
•Cross base sections (2)
- 3 -
PLASTIC
CROSS BASE (2)
POLE NUT
FAN BLADE
FRONT
GRILL HOOK
BLADE
KNOB
HANDLE
REAR GRILL
GRILL NUT
FRONT GRILL
CLIPS (4)
FRONT GRILL
HEIGHT
ADJUSTMENT
KNOB
POLE CENTER COVER
POLE ASSEMBLY
MOTOR SHAFT
MOTOR ASSEMBLY
THUMB SCREW
2.) Assemble the fan head:
• Remove the Grill Nut and Blade Knob from the
Motor Assembly. Note the Blade Knob is
“reverse” threaded and should be turned
“clockwise” to remove it from the motor shaft.
•Place the Motor Assembly on a flat surface
with the shaft facing up. Place the Rear Grill
over the motor shaft and on to the Motor Assembly.
The Rear Grill handle should be positioned toward
the top of the fan and the two holes in the Rear Grill
should be aligned with the two small plastic pins on
the Motor Assembly. Thread and tighten the Grill Nut
on to the Motor Housing securing the Rear Grill to the
Motor Assembly.
• Mount the Fan Blade on to the motor shaft by aligning
the “D” shaped hole in the Fan Blade with the “D”
shaped motor shaft. Insert the Fan Blade as far as possible on to the motor shaft
and secure with the Blade Knob turning the Blade Knob counter-clockwise. Do
not over tighten.
• Mount the Front Grill cover on to the Rear Grill cover by fully opening the clips
around the outer edge of the Front Grill. Align the top center non-opening hook
of the Front grill with the top center of the Rear Grill. Hold the Front Grill
against the Rear Grill and push the open clips on the Front Grill inward until Front
Grill is secure against the Rear Grill.
• The fan head assembly is now complete.
3.) Base Assembly:
• Take the 2 plastic base pieces, you will notice that one has a square cut out section
on the bottom of it and the other has the cut out on the top. Take the one with the
cut out section on the bottom and place it over the one with the cut out section on
the top in a crisscross pattern, align both cut out sections. Now firmly press these
two Base pieces together interlocking them.
• Tipping the interlocked Base pieces to a side insert the screw end of the Pole into
the hole in the center of the Base pieces, being sure to align the plastic tab with the
slot in the Base Hole. Then place Pole nut on screw end of pole and tighten
clockwise to secure Pole to Base pieces. *note- If base wobbles at all, you may
need to add the adhesive base leveling pads (included) to one or more of the base
feet. Base assembly is now complete.
4.) Final Assembly:
• Twist the Thumb Screw at the Bottom of the Motor Assembly counter-clockwise
until no threaded portion is visible within.
• Place the chrome end of the Pole Assembly within the Hole at the bottom of the
Motor Assembly and fully insert. If the Pole will not fully insert, the Thumb Screw
must be further loosened. Twist the Thumb Screw clockwise to tighten the Motor
Assembly to the Pole and Fan Assembly is now complete.
- 4 -
HANG FRONT GRILL HOOK
OVER TOP OF REAR GRILL
PUSH CLIPS TO
ASSEMBLE GRILL
OPERATION
• Place the assembled fan on a flat, level, firm and
dry surface.
• Plug the power cord into a polarized 120 volt AC
wall outlet.
• Turn the fan on and select the desired running
speed with the Speed Control Switch
conveniently and safely located at the front of the
fan below the Front Grill.
• To adjust the fan‘s height, loosen the Height
Adjustment Knob by unscrewing counter-
clockwise only a few turns. Pull upward on the
chrome portion of the Pole Assembly while
holding the lower portion firmly to raise the
height, or push down on the chrome portion to
lower. Retighten the Height Adjustment Knob,
being careful not to overtighten.
• The fan‘s direction can be adjusted relative to the
base by loosening the Thumb Screw at the bottom
of the Motor Assembly, and rotating the Fan Head.
• To set the fan into oscillation, depress the Oscillation
Knob on the top of the Motor Assembly. The Fan Head will pivot side-to-side and
up and down. For stationary operation, pull up on the Oscillation Knob.
Care, Cleaning & Storage
• The Fan Blade and Grill Set should be cleaned regularly for more efficient
operation. Unplug the fan, then reverse the assembly procedure to remove those
parts from the Motor Assembly before cleaning. Wipe with a damp cloth, then
towel dry.
• Never immerse any fan components in water. Wipe the fan only with a dry or
lightly moist cloth, then immediately towel dry.
• Always store the fan in a cool dry location
• Ensure that the fan is switched off from the supply mains before removing the
guard.
- 5 -
OSCILLATING
KNOB
PIANO
BUTTON
SWITCH THUMB
SCREW
HEIGHT
ADJUSTMENT
KNOB
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Nuvoo NVO-SF40BK User manual
-
Holmes HASF1796RC User manual
-
Bionaire BSF1731 User manual
-
-
-
-
-
-
Soleus Air Fan FS3-40R-30 User manual
-
