Heat & Glo FB-Reset Kit 2201-970 Install Manual

Brand: Heat & Glo

Model: FB-Reset Kit 2201-970

Type: Install Manual

Hearth & Home Technologies • FireBrick Reset Switch Kit Instructions • 2201-970 Rev. C • 1/11

FB-RESET Kit

Models: Escape-I30FB, Escape-I35FB, QFI30FB, QFI35FB

- Installation Instructions -

CAUTION! Risk of Cuts or Abrasions. Wear protective

gloves and safety glasses during installation.

KIT COMPONENTS

(1) Module Jumper Wire

(1) Module Reset Wire Assembly

(1) Rocker Switch

(1) Battery tray/switch

(1) Velcro Piece

Leave this manual with party responsible for use

and operation.

Figure 1. Remove Back Access Panel

Installation

1. Remove back access panel by removing the 5 screws

as shown in Figure 1.

2. Unplug the 6V adapter from the module. See Figure 2.

Figure 2. Unplug 6V Adapter from Module

SCREWS

6V ADAPTER

Figure 3. Plug in Jumper Wire Assembly

3. Plug the new jumper assembly into the 6V adapter and

the module as shown in Figure 3.

4. The battery tray is located in the lower left front of the

appliance as shown in Figure 4. A notch on the right

side of the tray engages the tray with the appliance.

See Figure 5 for location of notch. To remove the tray,

rotate the left side of the tray outward and pull to the left

to disengage the notch.

5. Remove the battery pack from the tray and discard the

metal battery tray.

Figure 4. Battery Tray Location

Figure 5. Reset Switch and Notch Location

RESET

SWITCH

NOTCH

BATTERY TRAY

Hearth & Home Technologies • FireBrick Reset Switch Kit Instructions • 2201-970 Rev. C • 1/11

Please contact your Hearth & Home Technologies

dealer with any questions or concerns.

For the location of your nearest Hearth & Home Technologies dealer,

please visit www.ﬁ reside.com

Hearth & Home Technologies Inc.

7571 215th Street West, Lakeville, MN 55044

www.ﬁ reside.com

6. Place the battery pack on the new supplied battery

tray with the Velcro supplied in the kit.

7. Feed the module reset wire assembly through the

front of the appliance to the back by the module.

8. Reinstall the new battery tray.

9. Connect the 24 inch wire assembly to the new mod-

ule wire assembly. See Figure 7.

10. Refer to shaded area on Figure 8 for completed wir-

ing diagram.

11. Reattach the back panel by installing the ﬁ ve screws.

Operation Instructions

This module may lock-out under certain conditions. When

this occurs, the appliance will not ignite or respond to

commands. The module will go into lock-out mode by

emitting three audible beeps, then continuously display a

RED/GREEN error code at its status indicator LED.

• Check battery tray. Remove batteries if installed.

Batteries should only be installed for power outages.

See appliance installation manual for more information.

• Locate the module reset switch. (See Figure 6).

• Set the module reset switch to the RESET position.

• Wait ﬁ ve (5) minutes to allow possible accumulated gas

to clear.

• Set the module reset switch to ON.

• Start the appliance.

WARNING! Risk of Explosion! DO NOT press the mod-

ule reset switch more than one time. Gas may accumu-

late in ﬁ rebox. Call a qualiﬁ ed service technician.

Figure 6.

Figure 7.

AUX WIRE EXTENSION

(2201-155)

LIGHT WIRE ASSEMBLY

(2201-013)

OPTIONAL

TO CORD ASSEMBLY

120VAC

AUX 300

MODULE

AUX1 AUX2

FAN

BATTERY PACK

6V DC (AA X 4)

ACCENT SOCKETS (2)

(2146-402)

EMBER BULB 20W (2)

(2088-136)

GROUND

ORANGE

(PILOT) GREEN

(MAIN)

TO CORD ASSEMBLY

120VAC MODULE ORG

WHT

INTERMITTENT PILOT IGNITOR

BLACK

RED

AUX2 NOT USED FOR INSERT MODELS.

PROTECTIVE COVER INCLUDED.

RC300 4.5V DC

(AA X 3)

MODULE

JUMPER WIRE

2179-300

MODULE RESET

SWITCH

2206-299

WIRE ASSEMBLY

2201-030

RESET SWITCH/OPERATION MODE

Figure 8. IPI Wiring Diagram

Heat & Glo FB-Reset Kit 2201-970 Install Manual

Heat & Glo FB-Reset Kit 2201-970 Install Manual

Heat & Glo FB-Reset Kit 2201-970 Install Manual

Related papers

Other documents