Haier HWD1000 - 1.7 cu. Ft. Washer/Dryer Combo User manual

Page is loading ...

IMPORTANTSAFETYIN:

Warning- Toreducetheriskof fire,electricshock,or iniurytopersonswhen using

yourepplience,followbesicprecautions,includingthefoflowing.

1. Read all instructions before using the appliance.

2. Use this appliance only for its intended purpose as described in this use and

care guide.

3. Use only detergents or softeners recommended for use in this appliance and

keep them out of the reach of children.

4. This appliance must be properly installed in accordance with the installation

instructions before it is used.

5. Never unplug your appliance by pulling on the power cord. Always grasp the

plug firmly and pull straight out from the outlet.

6. Replace immediately worn power cords, loose plugs/power outlets.

7. Unplug your appliance before cleaning or before making any repairs.

8. If your old appliance is not being used, we recommend that you

remove the door. This will reduce the possibility of danger to children.

9. Do not operate your appliance in the presence of explosive fumes.

10. Do not use this appliance to wash clothes soaked, spotted or washed in

gasoline, dry cleaning solvents or any other explosive or flammable

substances that could ignite and explode.

11. Clothes or rags used to clean flammable or explosive materials should not

be washed in this appliance till all traces of this material has been removed,

to avoid an accident.

12. Do not add or mix any flammable or explosive substances to the wash.

13. Do not try to remove clothes while the tub is moving. Let it come to a

complete stop before use.

14. The appliance loading door must be closed when tub is spinning.

15. Do not operate your appliance when parts are missing or parts are broken.

16. Do not use this appliance for commercial clothes washing.

17. Do not operate this appliance unless all enclosure panels are properly in

place.

18. Do not tamper with controls.

19. To reduce risk of injury do not allow children to play in or on the appliance.

Close supervision of children is necessary when the appliance is used

near children.

20. This appliance must be connected to proper electrical outlet with the correct

electrical supply.

21. Proper grounding must be ensured to reduce the risk of shock and fire. DO

NOT CUT OR REMOVE THE GROUNDING PLUG. If you do not have a

three-prongelectricreceptacleoutletinthewall,haveacertifiedelectrician

installtheproperreceptacle.ThewallreceptacleMUSTbeproperly

grounded.

22.Hydrogengasmaybeproducedifthewaterheaterhasnotbeenusedin

morethan2weeks.Thiscouldbeexplosiveundercertaincircumstances.Jf

thisisthecase,beforeusingthisapplianceturnonallthehotfaucetsandlet

thehotwaterrunforafewminutes.Thiswillletthetrappedhydrogen

escape.Duringthisprocessdonotturnonanelectricappliance,smoke,

lightamatch/lighteroruseaflametoavoidanaccident,ashydrogengasis

flammableandcanexplode.

23.Donotdryarticlesthathavebeenpreviouslycleanedin,washedin,soaked

in,orspottedwithgasoline,dry-cleaningsolvents,orotherflammableor

explosivesubstances,astheygiveoffvaporsthatcouldigniteorexplode.

24.Donotrepairorreplaceanypartoftheapplianceorattemptanyservicing

unlessspecifically recommended in the user-repair instructions that you

understand and have skills to carry out.

25. Do not use heat dry for articles containing foam rubber or similarly textured

rubber-like materials.

26. Clean button trap before and after each load.

27. Do not place items exposed to cooking oils in your dryer, items contaminated

with cooking oils may contribute to a chemical reaction that could cause a

load to catch fire.

28. To reduce the risk or electric shock or fire, do not use extension cords or

adapters to connect the unit to electrical power source.

T I T Ti

ForFutureUse

Risk of child entrapment. Before you throw away your old

appliance, take off the door so that children cannot easily get

trapped inside.

Thank you for purchasing our Haier

product. This easy-to-use manual will

guide you in getting the best use of

your washer & dryer combo unit.

Remember to record the model and

serial number. They are on a label in

back of the unit.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

PAGE

INSTALLATION INSTRUCTIONS ................................................................ 5

Tools and Materials Required ........................................................................ 5

Unpacking Your Unit .................................................................................... 6

Connection of Water Inlet Hose and Washing Machine .................................. 6

Water Drainage Hose .................................................................................... 7

Connection of Power Supply .......................................................................... 7

Grounding Instructions .................................................................................. 7

OPERATING INSTRUCTIONS .................................................................... 8

Parts and Features ...................................................................................... 8-9

Control Panel and Functions .................................................................. 10-12

Operational Functions ................................................................................ 13

Program Selection .................................................................................. 14-15

Washing Methods ........................................................................................ 16

Laundry Loading .......................................................................................... 16

Put Detergent in the Dispencer .................................................................... 16

Washing Program Setting ............................................................................ 16

Additional Jnfo ...................................................................................... 17-18

Tips ............................................................................................................ 17

Normal Operating Sounds .......................................................................... 17

CARE AND CLEANING GUIDE .......................................................... 18-19

Cleaning and Maintenance ........................................................................ 18

Moving and Vacationing and Storage of Your Unit ...................................... 18

Warning Codes .......................................................................................... 19

TROUBLESHOOTING .......................................................................... 20-22

ELECTRICAL CONNECTIONS .................................................................. 23

Grounding Instructions ................................................................................ 23

Power interruptions ...................................................................................... 23

You will need to have following tools to help you in the

installation of your Washer:

• Scissors

• Phillips Screwdriver

• Standard Screwdriver

• Pliers

• Wrench

• Tape Measure

• Gloves

• Level

Accessories Supplied Quantity

1. Hot & Cold wafer inlet 2

hoses

2. Drain Hose 1

3. Flat Water Inlet Hose 4

Washers

4. Drain holder 1

5. User Manual 1

® ®

®

® ®

® •

® ®

U pocki g Your Unit

Warning: To reduce the risk of fire, this appliance must be fastened or otherwise

secured to an uncovered floor.

• As shown in Fig. 1, remove all the packing materials (including the foam

base), it is normal that there are some water drops on the plastic bag, the

cushion and the porthole, it is because of the water testing before leaving the

factory.

• Remove the packing screws as shown in Fig.2.

The packing bolts protect the appliance from impact damage during

transportation. Follow the steps below before using the appliance.

1. Remove the rear panel of the washing machine.

2. Remove the three packing bolts from the rear panel of the washing

machine, the rubber hose and then the shock absorption steel channel.

3. Refit the back plate.

4. Fill the left holes by the packing bolts with plastic plugs.

Attention: The packing bolts and rubber hose should be kept in a safe place

for later use.

There is a plastic jacket packing the door catch. Please remove it when you

unpack the machine. Do not let children touch.

• Adjusting the position of the washing machine:

The washing machine is provided with adjustable feet. Before use, adjust the

feet until the appliance is leveled, as shown in Fig. 3.

Co ectio of wote i lllllet Bose wosBi g

_OC_i_@ (Use new hose-set, old hose-set should not be reused.)

• Connect the straight terminal of the inlet hose to the water tap and make sure

that it is fastened.

• Connect the bended terminal of the inlet hose to the solenoid valve and make

sure it is fastened.

• Be sure that the COLD inlet hose is connected with the solenoid valve for cold

water (marked with "C"), the HOT inlet hose is connected with the solenoid

valve for hot water (marked with "H").

• For easy recognition, Red line refers HOT inlet hose.

hese

• The height of the terminal for the water drainage hose should be between

31 "-40". The water drainage hose must be securely placed to the clip of the

washing machine.

• Use the water drainage support supplied as an accessory for proper

installation of the water drainage hose. Fix the water drainage hose support

with waterproof string. The water drainage hose should not be extended more

then 98" (longer extension will result in concurrent water inflow and outflow).

The diameter of the extension hose should be the same as the original hose.

Caution: Water drainage hose must not be immersed in water. The original and

extension hoses should be tightly connected.

Ce ectie pewe s pplf/y

Check the following items before connecting to the power supply.

• The socket conforms to the maximum power load (The maximum current load

of the socket and power supply cable should not be less then 15A).

• Power supply voltage conforms to the required value (120V/60Hz).

• The power supply socket and the plug of the washing machine are compatible.

Jf they are not compatible, refer to a washing machine technician or a

designated service point for power cable replacement.

• USE SUPPLYCONDUCTORS RATED 105 °C (221 °F).

G ou di g i st uctio s

• This appliance must be grounded. In the event of malfunction or breakdown,

grounding will reduce the risk of electric shock by providing a path of least

resistance for electric current. This appliance is equipped with a cord having an

equipped-ground conductor and a ground plug. The plug must be plugged

into an appropriate outlet that is properly installed with accordance to local

codes and regulations.

WARNING"

Improper connection of the equipped-ground conductor can result

in a risk of electric shock. Check with a qualified electrician or

serviceman if you are in doubt as to whether the appliance is

properly grounded. Do not modify the plug provided with the

appliance.

WARNING"

Certain internal parts are intentionally not grounded and may

present a risk of electric shock only during servicing. Service

Personnel-Do not contact the following parts while the appliance is

energized: electromagnetic valve, computer board, door lock, drain

pump, drying motor, capacity bracket assembly, etc...

7

e tu es

7" 8 I0_ 11 12....

17

13

I

2

1. On/Off Button

2. Program Button

3. Dry Cycle Selection Button

4. Spin Cycle Selection Button

5. Load Rinse Selection Button

6. Wash Cycle Selection Button

7. Delay Button

8. Remaining Time Display

9. Temperature Selection Button

10. Prewash Function Button

11. Water Level Selection Button

12. Door Lock Indicator

13. Start/Pause Button

14. See Through Glass Window Door

15. Button Trap

16. Front Adjustable Legs

] 7. Detergent/Softener

z

7

•LJ

4

1. Water Inlets (Hot/Cold)

2. Power Supply

(] 20V/6OHz, ] 5 Amps)

3. Drain Hose

4. Rear Adjustable Leveling Legs

5. Drainage Hose Clips (3)

6. Back Plate

7. Back Plate Screws (3)

7 8 9 10 11 12

13

1

WARNING: To reduce the risk of fire, electric shock, or inlury to persons, read

the IMPORTANT SAFETY INSTRUCTIONS before operating this

appliance.

1. Power On/Off

• This button controls On/Off power of the unit.

2. Program

" Touch this button and you can select the washing programs as you wish

from top to bottom in proper order. The backlight is bright while the

program is selected. The machine will carry out the standard program if

there is no program to be selected.

Attention: The machine has the memory function for "Custom" program.

3. Dry

• The sequence of dry program follows each time the button is selected after

the washing program is set:

" Whole auto dry program.

" The standard program for the individual dry.

" At this moment you can select either 60 rain or 30 rain program.

" You can not select dry function while you have already selected the heavy

or delicate program.

10

Attention: The maximum quantity of the laundry is 6 Ibs. if the dry function is

selected.

4. Spin

• The different spinning speeds can be selected by touching this button. For

details please see the program setting guide.

• The spinning speed is 1000 rpm (800 rpm for night washing) if the dry

function is selected.

5. Rinse

• Touch this button to select the rinsing time. The time can be changed when

button is pressed and 6 times are the maximum amount.

6. Wash

• Touch this button to select the washing time. Each time this button is

pressed, washing period will increase. The steps are increments of one

miunute for one press.

7. Delay

Setting the finished time of the scheduled washing by touching this button.

The defaulted time for the scheduled washing is 9 hour. The washing time

can be increased one hour by one touching of the button. If the button is

pressed and held the time can be varied from 1 to 24 hours till the button

is released. If the START/PAUSEbutton is pressed the current setting is

confirmed after the scheduled washing program is ready.

If the time for the washing program is longer than the time of the scheduled

washing then the program will work immediately after the STARTbutton is

pressed.

Attention: There is some difference between the setting time and actual

time because of the water temperature, water pressure and the

distrubution of the laundry in the tube. There is no scheduled

washing function for "Delicate" program.

8. Remaining time: Min (Digital display screen)

• This display is used for providing washing time to the user. It can display the

setting time of scheduled washing and heating temperature. The screen

displays only the hour if the time setting is over 10 hours.

9. Temp (Children lock)

10.

o

• Touch this button to set washing cycle with cold or hot water. The digital

display screen shows "W", "H", "C". The default value is "W"

W-hot and cold water; H-hot water; C-cold water.

Lock buttons on the control panel, including the Power button, by pressing

this button for 3 seconds. These can be unlocked if the button is pressed for

another 3 seconds.

Prewash

The prewash function can be added into the washing program.

11

11.Waterlevel

* The related time and water level in the drum can be selected by pressing

this button according to the laundry quantity. The quantity indicator changes

its position according each time the laundry quantity button is pressed. We

suggest using the first gear when the quantity is less then 2 Ibs.; use the

second gear when the quantity is less then 6 Ibs., and use the last gear

when the quantity more then 6 Ibs. All other program setting indicate the

default values when the laundry quantity is set. For each settings range

please see the program setting for reference. The default program will be

carried out if the function is not selected.

12. Door lock indicator

This indicates that the door is locked and the machine is in the operation

state and the door can not be opened. Jfthe condition for opening the door

is met, press the START/PAUSEbutton. When this ligh is off and the door will

be unlocked and can be opened.

13. Start/Pause

* The set program is carried out while this button is pressed. To pause the

current program, just press this button and the program will not operate at

the moment. Press this button again if you want to resume the operation.

14. See Through Class Window Door

• Physical part that allows user to see what is happening inside.

15. Button Trap

* Physical part that collects lints and other small materials.

16. Front Adjustable Legs

. 2 physical parts that can be adjusted in height for user needs.

17. Detergent/Softener Dispenser

Physical part where user can place detergent or softener.

12

Powersupply

e

Water

supply

Detergent

selection

Laundry

treatment

e

120V/60Hz/15Ams.

Turn on the tap and ensure that the water is clear.

Caution: Before starting the washing machine turn on

the water faucet to ensure that the water faucet and the

water inlet hose are connected and do not leak.

The washing result depends on the quality of the

detergent except the function performances of the

washing machine. There are many brands of detergent

in the market. For the best washing result, we suggest

you use the special detergent that produced for the auto

drum washing machines.

For washing wool and the chemical fiber please use

special detergent. Do not use dryclean dissolvent.

Attention: Put only enough detergent for one load of

laundry into cartidge at a time.

Sort out clothes according to type and extent of dirt.

There are three types of clothes: cotton, synthetical and

woolen (silk) fabrics.

Separate white clothes from colors.

Remove all objects from pockets that may cause

damage to the machine, such as keys and coins.

Repair damaged clothing, loose buttons or damaged

zippers before washing.

Bed sheets and table cloths should be loosely loaded

and not folded.

This washing machine is for household use and

designed to mechanically wash clothes.

Type Non-Fade Delicate Woolen Blending

Cotton s fabrics

Max Load I I Ibs. 4.4 Ibs. 2.2 Ibs. 5.5 Ibs.

13

Program

Prewash

Standard

Custom

Quick

Night

Option

N/A

wash/rinse/spin

wash/rinse/spin/dry

wash/rinse/spin

wash/rinse/spin/dry

wash/rinse/spin

wash/rinse/spin/dry

wash/rinse/spin

wash/rinse/spin/dry

wash/rinse/spin

Suitable

condition

dirty cloth

ordinary

clothes

washing

self defined

washing

program

accord-

ing to the

habit of the

operator

for not

very dirty

clothes

Heavy for thick

or heavy

clothes

Delicate wash/rinse/spin cashmere N/A 6 1-15 2 0-6

and wool

fabrics

Standard dry dry the N/A 120 N/A N/A N/A

ordinary

laundries

60 rain dry dry the N/A 60 N/A N/A N/A

ordinary

laundries

30 rain dry anti-virus N/A 30 N/A N/A N/A

procress

for dried

laundry

14

60 8 5-60 2 0-6

60 6 5-60 2 0-6

60 5 5-60 2 0-6

60 25 5-53 3 0-6

60 20 5-53 3 0-6

60 ]5 5-53 3 0-6

30 40 5-60 3 0-6

Program and washing time

Wash (min) Rinse (min)

DefauJt Range DefauJt Range

add 12 N/A N/A N/A

minutes

was

washing

25

21

17

25

21

17

5-60 3 0-6

5-60 2 0-6

5-60 3 0-6

5-60 2 0-6

for night

washing

ture (max)

oC

N/A

9O

Spin (rpm)

hot/cold water)

Default Range Default Range Default Range

/ / / / / / * * o

800 0-600-800/1000 W C/H/W 56 7-130 4, -k 0

1000 0-600-800/1000 W C/H/W 168 7-251 4, * 0

1000 0-600-800/1000 W C/H/W 103 7-190 4, * 0

800 0-600-800/1000 W C/H/W 59 7-130 4, -k 0

1000 0-600-800/1000 W C/H/W 168 7-251 4, * 0

1000 0-600-800/1000 W C/H/W 103 7-190 4, * 0

800 0-600-800/1000 W C/H/W 32 7-128 4, -k 0

1000 0-600-800/1000 W C/H/W 151 7-249 4, -k 0

1000 0-600-800/1000 W C/H/W 89 7-188 4, * 0

800 0-600-800 W C/H/W 67 7-137 4, -k 0

800 0-600-800 W C/H/W 184 7-259 4, -k 0

800 0-600-800 W C/H/W 118 7-198 4, -k 0

600 0-600 W C/H/W 77 7-139 4, -k 0

600 0-600 C C/H/W 29 3-82 4, -k 0

/ / / / 120 120 4, 4, 4,

/ / / / 60 60 4, 4, 4,

/ / / / 30 30 4, 4, 4,

Program and washing time Methods for using detergent

Temp (selecting Total time (min) Partition 1 Partition 2 Partition 3

15

Be ding

Evenly load the laundry in the washing machine and then tightly close the door

of the unit.

Note: 1.When first using the washing machine, let it run unloaded for one

program to prevent the laundry from being stained by oil or dirty water

from the washing machine.

2.Do not overload the washing machine.

P_t detergent in the dispenser

There are three partitions in the detergent.

Partition 1: It is used for the prewash function.

Partition 2: Put the detergent in this partition no matter whether the prewash

function is selected or not.

Partition 3:

Caution: 1.

2.

3.

Put the softening agent in this partition if the laundry has gone

through the softening process.

Do not add liquid detergent into partition land 2.

For prewashing program, detergent should be added to both

partition 1 and 2; for other programs, do not add detergent to

partition 1.

Do not overuse softening agent as this may damage arfifical fabrics.

W_s_ing p_eg_m setting

Set the washing program correctly in accordance with the laundry load. First

connect the mains and select the power on/off button. The machine will work on

the default standard program. Select the program selection button for the

required washing program.

The above operation should be under the condition of no power down. The

machine will continue its previous program since the machine has the memory

function after the power down. The memory function can be canceled by turning

off the power and restart it.

16

WARNING: To reduce the risk of fire, do not dry items containing

foam rubber or similarly textured rubber-like materials.

• Adding the softener agent can help the laundry to get rid of the static

electricity and make the clothes feel soft and easy to iron.

• The following list shows drying time for the different quantity and

kinds of laundry. You can select the expected drying program in

accordance with the quantity of the drying load. The selected

program will be over when the drying process is finished.

Weightof laundry

(lb.)

0-2

2-6

0-2

2-6

Tirne for drying

Standard

Remain tirne

(rnin)

59

120

60 rnin 60

0-6 30 rnin 30

Drying degree

Dried

For ironing

Dry and

anti-bacterium

Prograrn

No m lllli Operatisg Sousds

The following sounds are normally heard during the operation of the

washer:

• Tumbling sounds: this is normal as the heavy wet clothes in the

washer are continuously being tossed around.

• Air rushing noise: This happens when the washer tub spins at very

high RPM.

• Wash and Rinse cycles going on and off will also make clicking

sounds.

17

Warning: Always unplug your appliance to avoid electric shock before cleaning.

Ignoring this warning may result in death or injury. Before using

cleaning products, always read and follow manufacturer's instructions

and warnings to avoid personal injury or product damage.

Use only damp cloth for cleaning control panel.

* To avoid any kind of damage to cabinet finish, wipe appliance cabinet as

needed, if you spill liquid softener, bleach or detergent on the cabinet, wipe

cabinet immediately because it can damage the finish.

* Do not use any abrasive, harsh chemicals, ammonia, chlorine bleach,

concentrated detergent or solvents. Some of these chemicals may dissolve,

damage and/or discolor your appliance.

" Remove pins or other sharp objects from clothes to prevent scratching

interior parts.

* We suggest that you check the button trap no more than twice a year. Do not

use washer without button trap in its place.

The Detergent Dispenser Compartment has a removable option. Over time,

this compartment may accumulate dried detergent, dirt and debris. You must

remove the dispenser, then rinse it in a sink to remove dirt if present.

M@vi g & Vacati@ i g

* Turn off water supply faucets and disconnect hoses. Drain water from all hoses.

This will prevent damage due to water leakage if the hoses accidentally get

ruptured or they become loose.

* Disconnect eledrical plug.

* Dry inner wash tub. If moving washer, disconnect drain hose.

* Turn the leveling legs clockwise all the way in.

* Reinstall both shipping bolts and metal brackets in the back to prevent internal

part from shaking when appliance is moving to another location.

* To prevent mold leave door open so moisture inside machine can evaporate.

5re,age Yeur ppl[/ia ¢e in Cellllid

* This appliance must be stored at room temperature.

. If you just got delivery of this appliance when outside temperature is below

freezing, do not operate until this appliance has warmed to room temperature.

. Do not install or operate this appliance in the area where room temperature is

below freezing.

18

Warning Item of Content of Action to take Checking position

code concern identification and ask for help

Water supply The water level can not Warning and stop Check if the water

reach the reset water level running pressure or water

E11 within 5 minutes supply is low

Drainage The water level can not Warning and stop Check if the water

reach the setting water level running pressure is low or

within 8 mintues stops supplying

E12 Drainage The water level can not Warning and stop Check the water

reach the reset level in 8 running outlet of the drainage,

minutes after drainage adjust it and restart

starting the machine

E13 Water supply The water is above the Warning and stop Ask the technician to

warning level running repair it

E31 Motor The feedback signal does Warning and stop Ask the technician to

not change in 8 minutes running repair it

during the motor runs

EA3 Water level is The water setting level Warning and stop Check the water

abnormal in during the drying process running outlet of the drainage

the drying required and adjust it

process if required and restart

the machine

EC4 The tempera- Within 30 minutes of dry Warning and stop Ask the technician to

ture of air vent cycle there is 5 minutes in running repair it

which the temperature is not

increasing

EC5 The dry The drying sensor circuit Warning and stop Ask the technician to

temperature short or open running repair it

sensor

U01 Door is locked Can not unlock Warning and stop Ask the technician to

running repair it

U02 Door is not Can not lock the door Warning and stop Ask the technician to

locked running repair it

U03 Spin Iopsidely The judgement of Spin at low speed Ask the technician to

un-balance is above 1000g and cancel drying repair it

U04 The door is The door is opened Warning Close the door

opened

E22 The memory EEPROM is not functioning Warning Ask the technician to

function has repair it

failed

19

Washer does not operate:

• Check if unit is plugged in. The plug may have come loose.

• Check if the electrical wall receptacle has proper voltage.

• Check if the circuit breaker needs to be reset or if the fuse needs to be

replaced.

• Check if the unit is in "Off" mode.

• Check if the washer is overloaded: load may need to be re-balanced and

clothes may need to be redistributed.

• Check if the door is open. You may have to close the door properly.

Problems with water:

• Not enough water coming out: Water faucet may need to be turned on fully.

Water hoses may be tangled up or wrinkled up. Straighten up hoses. Check

water level selection, it may need to be readjusted.

• Water Temperature is incorrect: Check your water heater temperature. Hot

water needs to be at a temperature at least 120°F-140°F (49°C - 60°C).

Check to make sure the inlet hoses are properly connected. (e.g. hot to hot &

cold to cold)

• Water leaks: This is due to not improperly installed drain hose or fill hoses.

Your home drain may be clogged. You may need to tighten hoses, check the

plumbing or call a plumber for service.

• Water pumped out before the cycle is completed: It happens if you open the

door in the middle of cycle.

• Water will not drain: This may be because drain hose was not installed

properly. Check the position of the drain hose. In order to drain properly, make

sure that top of drain outlet is less than 4 ft. (] .2 m) above the floor.

2O

Page is loading ...

Haier HWD1000 - 1.7 cu. Ft. Washer/Dryer Combo User manual

This manual is also suitable for

Haier HWD1000 - 1.7 cu. Ft. Washer/Dryer Combo User manual

in other languages

Related papers

Other documents