Atomik Atomik Metal Mulisha Brian Deegan 1:8 Ford Raptor 150 RC Truck Owner's manual

Page is loading ...

Atomik-RC.Com

1

2

3-4

5-6

7

8

9-16

17-24

25-32

33-40

41-52

47-48

53

54

Introduction

Required Items

Safety Warnings

Transmitter Functions

Troubleshooting/Maintenance

Warranty/Contact Info

Spanish Instructions

French Instructions

German Instructions

Japanese Instructions

Vehicle Assembly

Exploded View

Replacement Part List

Option Part List

Vehicle Set-up Sheet

TABLE OF CONTENTS

2

Atomik-RC.Com

9201

BEFORE YOU START ASSEMBLING

Thank you for purchasing the Atomik™ Brian Deegan Metal Mulisha 1/8th Scale Ford

Raptor Short Course Truck. This kit was designed to be fun and easy-to-drive using high

quality parts for great performance and durability. Please read this instruction manual

thoroughly before using this product; paying close attention to the warnings and call out

notes. The valuable tips in this manual can help prevent accidents and improper use that

can lead to part failure or injury.

This kit is a high performance R/C vehicle that requires regular maintenance for best

performance. If you are unclear on any step or are unsure about how to use your new

Atomik™ Brian Deegan Metal Mulisha 1/8th Scale Ford Raptor Short Course Truck, give our

Customer Service Department a call at 800-705-0620 (208-762-0620 for International

customers) and we will be happy to help. You can also email us at

[email protected].

1.2 V AA Battery X4

Reamer CA Glue

Cross Wrench

(Large)

Cross Wrench (Small)

Nut Driver

5.5 mm 7 mm

Allen Key

2 mm

2.5 mm

3 mm

1.5 mm

Hobby ScissorsNeedle Nose Plier

Silicone Oil

5.5mm Open end Wrench

Grease

Thread Lock

Compound

Atomik-RC.Com

3

SAFETY PRECAUTIONS

- Keep packaging and instruction as they contain important information.

- Do not attempt to modify this product in any way.

- Do not submerge this product in water as it can damage the electronics.

- Keep away from animals and young children. Never operate your model around

wildlife, or inattentive people. The speed of this model can cause severe injury and

damage if a collision occurs.

- Some of the electronic components may become very hot during use and can cause

severe burns if touched before they cool. Let the model stand and cool down before

handling the motor, ESC and battery.

- Your model is operated by radio signals sent by the transmitter. This system is

susceptible to interference from other radio signal sources. Before using your model,

make sure there is no interference in the area.

- Keep moving parts away from hair, clothing, and hands. The spinning parts on this

model can cause severe injury. Remain clear of spinning wheels and drive shafts when

the vehicle is running.

- The battery used in this model can be dangerous. If the battery gets hot during

charging, discontinue charging immediately and disconnect battery from the charger.

Never leave the battery unattended while charging. If you are unsure of how to charge

this battery, please contact Atomik or seek the advise of your local hobby shop. Never

let children charge batteries without adult supervision.

- Charging and discharging batteries has the potential for serious injury to persons and

damage to property. In purchasing this product, the user agrees to accept responsibility

for all such risks, and will not hold Atomik, it’s afﬁliates, manufacturers, distributors, or

retail partners responsible for any accident, injury to persons, or damage to property

resulting from the use of this product. This product contains chemicals known to the

State of California to cause Cancer, birth defects and other reproductive harm. Be

responsible, dispose of properly.

- Keep packaging and instruction as they contain important information.

- Do not attempt to modify this product in any way.

- Do not submerge this product in water as it can damage the electronics.

- Keep away from animals and young children. Never operate your model around

wildlife, or inattentive people. The speed of this model can cause severe injury and

damage if a collision occurs.

- Some of the electronic components may become very hot during use and can cause

severe burns if touched before they cool. Let the model stand and cool down before

handling the motor, ESC and battery.

- Your model is operated by radio signals sent by the transmitter. This system is

susceptible to interference from other radio signal sources. Before using your model,

make sure there is no interference in the area.

- Keep moving parts away from hair, clothing, and hands. The spinning parts on this

model can cause severe injury. Remain clear of spinning wheels and drive shafts when

the vehicle is running.

- The battery used in this model can be dangerous. If the battery gets hot during

charging, discontinue charging immediately and disconnect battery from the charger.

Never leave the battery unattended while charging. If you are unsure of how to charge

this battery, please contact Atomik or seek the advise of your local hobby shop. Never

let children charge batteries without adult supervision.

- Charging and discharging batteries has the potential for serious injury to persons and

damage to property. In purchasing this product, the user agrees to accept responsibility

for all such risks, and will not hold Atomik, it’s afﬁliates, manufacturers, distributors, or

retail partners responsible for any accident, injury to persons, or damage to property

resulting from the use of this product. This product contains chemicals known to the

State of California to cause Cancer, birth defects and other reproductive harm. Be

responsible, dispose of properly.

4

Atomik-RC.Com

9201

SAFETY PRECAUTIONS

- Do not mix old and new batteries.

- Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

- Rechargeable batteries are to be removed from the transmitter before being charged.

- Non-rechargeable batteries are not to be recharged.

- Rechargeable batteries are only to be charged under Adult Supervision.

- Only batteries of the same or equivalent type as recommended are to be used.

- Remove batteries if the product will be stored for an extended period of time.

- Never leave batteries unattended while charging. Always observe batteries when

charging so that you may react quickly to any problems that may occur.

- Do not charge a battery (pack) that is hot, wet or shows signs of leakage or corrosion.

- Do not expose to ﬁre, as this may result in explosion.

- AA/LR6 batteries may present a choking hazard - keep away from young children.

- User should remove the battery from the item before disposal.

- After use, the battery pack will be hot! Wait until it cools before recharging.

- Recharging a warm or hot battery (pack) will greatly shorten the battery’s life.

- Unplug the adaptor from the electrical outlet if it is not going to be used for a long

period of time.

- Always check your model for loose screws and components before operating.

- Always unplug the battery before removing debris from the wheels or driveline

components.

- Minors under the age of 14 require adult supervision when using this vehicle.

- Do not mix old and new batteries.

- Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

- Rechargeable batteries are to be removed from the transmitter before being charged.

- Non-rechargeable batteries are not to be recharged.

- Rechargeable batteries are only to be charged under Adult Supervision.

- Only batteries of the same or equivalent type as recommended are to be used.

- Remove batteries if the product will be stored for an extended period of time.

- Never leave batteries unattended while charging. Always observe batteries when

charging so that you may react quickly to any problems that may occur.

- Do not charge a battery (pack) that is hot, wet or shows signs of leakage or corrosion.

- Do not expose to ﬁre, as this may result in explosion.

- AA/LR6 batteries may present a choking hazard - keep away from young children.

- User should remove the battery from the item before disposal.

- After use, the battery pack will be hot! Wait until it cools before recharging.

- Recharging a warm or hot battery (pack) will greatly shorten the battery’s life.

- Unplug the adaptor from the electrical outlet if it is not going to be used for a long

period of time.

- Always check your model for loose screws and components before operating.

- Always unplug the battery before removing debris from the wheels or driveline

components.

- Minors under the age of 14 require adult supervision when using this vehicle.

Atomik-RC.Com

5

1) Install 4 AA batteries into transmitter.

2) Turn transmitter ON.

3) Connect battery to the ESC. Turn On ESC. After 1-2 seconds the motor will

beep, indicating power is applied and is working properly.

4) Move steering controls right and left to ensure the model is reacting

correctly to inputs. If not, reverse the servo direction. Refer to the photo

above to ﬁnd the servo-reversing switch.

5) Adjust the steering trim until both wheels appear even. Consult the drawing

below for how to adjust the steering trim.

6) While holding the model elevated off the ground, give throttle and brake

inputs on the transmitter to ensure your model is reacting accordingly.

7) The transmitter should always be turned ON ﬁrst and OFF last. (Be sure to

unplug your battery.)

6

Atomik-RC.Com

9201

TRANSMITTER ADJUSTMENT

The receiver in your 1/8th Scale Brian Deegan Metal

Mulisha Ford Raptor Short Course Truck is equipped with

a radio Fail-Safe. This means if the vehicle goes out of

range, transmitter goes dead, or other outside interfer-

ence occurs, the controls will return to a pre-set

position, usually neutral steering, and no throttle.

1) Make sure the steering and throttle controls are in their

neutral positions. Turn On the transmitter, and then the

receiver.

2) Press the Fail-Safe Button on the Receiver. The LED on

the receiver should be ﬂashing once the button is

pressed.

3) Put the steering and throttle controls in the desired

position. Usually, both should be left at neutral. Press the

Fail-Safe button on the receiver. The settings will take

effect when the LED on the receiver goes from ﬂashing,

to a solid red.

4) Test the Fail-Safe with the vehicle on a stand to prevent a

runaway vehicle. Apply some steering control, or throttle

input. While holding that input, turn Off the ESC. The

throttle should shut down, and the steering should

center. If not, repeat steps 1-3 above.

Position the throttle trigger in the neutral position, adjust the throttle

trim so the wheels do not spin

Receiver and Servo Connection

Binding the Transmitter and Receiver

Atomik-RC.Com

7

TROUBLESHOOTING

SERVICE AND MAINTENANCE

PROBLEM CAUSE

Does Not Move

1) Battery may be dead in model or transmitter.

2) Damaged motor.

3) Damaged ESC.

No Control

1) Antenna may be broken or oriented incorrectly.

2) Model may be out of range from transmitter.

3) Weak or dead battery in transmitter.

4) Receiver not bound correctly to transmitter.

Short Run Time

1) Battery may be damaged.

2) Charger may be damaged.

Your Brian Deegan Metal Mulisha 1/8th Scale Ford Raptor Short Course Truck is a high

performance RC vehicle. From time to time it will require simple maintenance to keep it

running at top performance. Follow the steps below to ensure the longest life and best

performance of your vehicle.

1) Clean your vehicle after every use to prevent damage and excess wear from debris.

2) Check for loose screws, nuts, or other unsecured parts. Apply Thread Locking

Compound (T.L.C.) to all screws that are fastened into metal. Do not apply T.L.C. to

screws that go into plastic as this may damage the plastic.

3) Check for excess play or slop in all moving parts. This includes driveline components,

suspension parts, and bearings. Some items will wear over time and may require

replacement.

4) If your vehicle becomes submerged in water, after running, clean off the vehicle, open

the receiver box, and with compressed air, blow out any excess water in all

components.

5) Lube bearings with a light silicone oil or bearing oil to maintain best bearing

performance. If you run in wet conditions, be sure to lube all bearings frequently to

prevent them from rusting.

6) Check all electronic connections. Inspect the ESC and battery terminals. Over time they

can become dirty, which increases resistance and robs power from the system.

8

Atomik-RC.Com

9201

WARRANTY

INFORMATION

General Warranty Policies

Atomik™ warrants this product to be free of material and workmanship defects when new. Atomik™ will at its sole discretion repair or replace defective

components free of charge within 90 days from date of purchase or within 30 days for all electronic components.* This warranty does not cover wear and tear,

crash damage, modiﬁcations, failure to perform routine maintenance, or any damages arising as a result of improper use. All warranty claims are to be directed

to Atomik™ Customer Service at 1-800-705-0620 (208-762-0620) or [email protected].

*Please refer to the Venom™ Lifetime Battery Replacement Plan for warranty information pertaining to all rechargeable battery packs.

GUARANTEE

All products are inspected and adjusted individually before leaving the manufacturer and are guaranteed to be free of material defects and manufacturing faults.

Venom™ Lifetime Battery Replacement Plan

We are so certain of the quality of our battery line that we offer a Venom™ Lifetime Battery Replacement Plan on all of our rechargeable battery packs. Venom™

will, at our discretion, replace defective batteries free of charge within a period of 1 year from date of purchase. Year 2 onward, any Venom™ battery can be

exchanged for a brand new battery of same size and type for 30% off original retail pricing. This warranty does not cover normal wear and tear, crash or water

damage, modiﬁcations, or any damages arising as a result of improper use. All warranty claims are to be directed to Venom™ Customer Service at

1-800-705-0620 (208-762-0620) or [email protected]. *We reserve the right to deny replacement to any serial abusers of our policy.

Important Notice

Atomik™ assumes sole responsibility for our products; therefore, dealers should not be involved in any warranty issues. All warranty claims are to be directed

to Atomik™ Customer Service. Before returning any defective product, please contact Atomik™ Customer Service at 800-705-0620 (208-762-0620) or

[email protected] to receive a Return Merchandise Authorization Number. A dated & itemized sales receipt must accompany any product

returned for warranty work.

Release of Liability

Atomik™, It’s afﬁliates, manufacturers, distributors, or retail partners shall not be held liable for any accident, injury to persons, or damage to property resulting

from use, misuse, or abuse of any Atomik™ product. In purchasing a Atomik™ product the user agrees to accept responsibility for all such risks.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowl-

edge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Charging and discharging batteries has the potential for serious injury to persons and damage to property. In purchasing this product, the user agrees to accept

responsibility for all such risks, and will not hold Atomik™, it’s afﬁliates, manufacturers, distributors, or retail partners responsible for any accident, injury to

persons, or damage to property resulting from the use of this product.

Adult supervision is required when using this product. This product should be assembled by an adult before use. Proper assembly should be checked by an adult

before use. This product should be periodically examined by an adult for potential hazards. Any potential hazardous parts should be repaired or replaced.

WARNING: This product may contain sharp edges or objects that can cause cuts or other bodily injury. To prevent cuts or other bodily injury, do not contact

sharp edges or objects.

FCC Warning:

FCC ID: XNZHTX-242

CAUTION: Atomik™ is not responsible for any radio or TV interference caused by unauthorized modiﬁcations to this product. Changes or modiﬁcations not

authorized by Atomik™ will void all warranties.

NOTE: This product has been tested and found to comply with the limits for a Class B digital device, compliant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio

frequency energy and, if not installed and used as instructed, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined

by turning the product on and off, correct the interference by trying one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from the receiver.

- Consult the dealer or an experienced radio/TV technician for help.

This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Be responsible, dispose of

properly.

Notice of Rights

otherwise, without the prior written permission of Atomik™. For information on getting permission for reprints and excerpts, contact

[email protected].

Notice of Liability

The information in this manual is distributed on an “As Is” basis, without warranty. While every precaution has been taken in the preparation of the manual,

Atomik™ does not have any liability to any person or entity with respect to any loss or damage caused or alleged to be caused directly or indirectly by the

information contained in this manual or by the products described in it.

Actual product may vary from product shown. Product is subject to change.

Page is loading ...

Atomik-RC.Com

41

10124

16 x 8 x 5mm

10124

16 x 8 x 5mm

10139

M5 x 4mm Set Screw

10076

M4 x 4mm Set Screw

9262

17 x 6.3 x 0.3 Washer

9271

2.5 x 11mm Pin

9207

1.75 x 9 O-ring

10069

M3 x 12mm BH Screw

4

10124

9241

10139

9230

10069

9210

9212

9205

10046

M3 x 12mm CH Screw

DIFFERENTIAL GEAR

ENGRANAJE IMPULSOR - BOÎTIER DE DIFFÉRENTIEL - DIFFERENZIALGETRIEBE -

ASSEMBLY

FRONT GEAR BOX / SHOCK TOWER

CAJA DIFERENCIAL DELANTERA / TORRE - BOÎTE DE VITESSE AVANT - TOUR D'AMORTISSEUR

VORDERER RADKASTEN / STOßDÄMPFER - /

9206

10124

9206

10076

9208

9262

9209

9271

9207

10046

Fill up with different oil into

the diff. case until the oil

surface is about 3.0mm lower

than the top of the case.

Front 5000#

Rear 3000#

Llene el cárter del diferencial

de aceite hasta que la

superficie del aceite esté

unos 3.0 mm más debajo de

la parte superior del cárter.

Delante nº 5000

Detrás nº 3000

Remplissez le boîtier de différentiel

avec de l'huile différente jusqu'à ce

que la surface de l'huile arrive à

environ 3 mm au-dessous de la

partie supérieure du boîtier.

Avant 5000#

Arrière 3000#

Befüllen Sie das Gehäuse des

Differenzialgetriebes mit

unterschiedlichem Öl, bis sich der

Ölstand 3 mm unter der Oberseite

des Gehäuses befindet.

Vorderseite 5000#

Rückseite 3000#

3.0mm

5000#

3000

ASSEMBLY

Page is loading ...

Atomik-RC.Com

43

10124

10125

9231

9269

9225

9229

10139

9229

9286

10068

9215

9244

9226

9257

9258

10083

9227

9257

9254

9216

10020

10078

10087

REAR SUSPENSION

SUSPENSIÓN TRASERA - SUSPENSION ARRIÈRE - HINTERE GABELFEDERUNG -

STEERING

DIRECCIÓN - DIRECTION - LENKUNG -

10020

10087

9257

9258

9235

9233

9256

9243

10087

10080

10020

M3 x 12mm SH Screw

10080

M3 x 13.5mm

10087

M3 Lock Nut

10124

16 x 8 x 5mm Bearing

10125

21 x 15 x 4mm Bearing

9269

3 x 17mm Pin

10139

M5 x 4mm Set Screw

10087

M3 Lock Nut

10068

M3 x 10mm BH Screw

10083

M4 x 16mm CH Screw

10078

M3 x 24mm SH Screw

10020

M3 x 12mm SH Screw

ASSEMBLY

9257

10020

9236

10078

10013

10014

9236

10044

9257

10023

9253

9258

10087

FRONT SWAY BAR

BARRA ESTABILIZADORA FRONTAL - BARRE STABILISATRICE AVANT -

VORDERER STABILISATOR -

9232

9231

10087

9228

9229

9266

10138

10078

10087

10078

9229

10083

9220

FRONT SUSPENSION

SUSPENSIÓN FRONTAL - SUSPENSION AVANT - GABELFEDERUNG VORNE -

10125

9213

9270

10124

9244

10139

9269

9214

10137

9223

9269

3 x 17mm Pin

9270

3 x 15mm Pin

10124

16 x 8 x 5mm Bearing

10125

21 x 15 x 4mm Bearing

10137

M4 x 14mm BH Screw

10139

M5 x 4mm Set Screw

10087

M3 Lock Nut

10083

M4 x 16mm CH Screw

10078

M3 x 24mm SH Screw

10020

M3 x 12mm SH Screw

10023

M3 x 18mm SH Screw

10078

M3 x 24mm SH Screw

10013

M3 x 3mm Set Screw

10014

M3 x 10mm Set Screw

ASSEMBLY

44

Atomik-RC.Com

9201

10124

10125

9231

9269

9225

9229

10139

9229

9286

10068

9215

9244

9226

9257

9258

10083

9227

9257

9254

9216

10020

10078

10087

REAR SUSPENSION

SUSPENSIÓN TRASERA - SUSPENSION ARRIÈRE - HINTERE GABELFEDERUNG -

STEERING

DIRECCIÓN - DIRECTION - LENKUNG -

10020

10087

9257

9258

9235

9233

9256

9243

10087

10080

10020

M3 x 12mm SH Screw

10080

M3 x 13.5mm

10087

M3 Lock Nut

10124

16 x 8 x 5mm Bearing

10125

21 x 15 x 4mm Bearing

9269

3 x 17mm Pin

10139

M5 x 4mm Set Screw

10087

M3 Lock Nut

10068

M3 x 10mm BH Screw

10083

M4 x 16mm CH Screw

10078

M3 x 24mm SH Screw

10020

M3 x 12mm SH Screw

ASSEMBLY

Atomik-RC.Com

45

10022

10013

10014

10023

10044

9237

9285

10069

9263

10071

10069

9265

10071

10087

9265

10079

9267

10084

10070

REAR SWAG BAR/BODY MOUNTS

BARRA ESTABILIZADORA TRASERA - CARROCERÍA / BARRE STABILISATRICE ARRIÈRE - RENFORTS

DE CAISSE / HINTERER STABILISATOR - KAROSSERIEHALTER / /

REAR BUMPER

PARACHOQUE TRASERO - PARE-CHOC ARRIÈRE - HINTERE STOßSTANGE -

10071

M3 x 16mm BH Screw

10069

M3 x 12mm BH Screw

6

10022

M3 x 16mm SH Screw

10023

M3 x 18mm SH Screw

10044

M3 x 8mm CH Screw

10014

M3 x 10mm Set Screw

10013

M3 x 3mm Set Screw

10079

M3 x 26mm SH Screw

10084

M4 x 26mm CH Screw

10087

M3 Lock Nut

10070

M3 x 14mm BH Screw

ASSEMBLY

46

Atomik-RC.Com

9201

10045

9222

9286

10068

10082

10135

10081

9224

9234

10070

10126

10044

10045

10087

9217

10047

10046

9238

10068

9221

9259

9240

10067

TENSION ROD - CENTER DIFFERENTIAL - CHASSIS

VARILLA DE TENSIÓN / DIFERENCIAL CENTRAL / CHASIS - BARRE DE TENSION / DIFFÉRENTIEL CENTRAL / CHÂSSIS -

ZUGSTANGE / MITTELDIFFERENZIAL / CHASSIS - / /

FRONT SUSPENSION - CHASSIS

SUSPENSIÓN FRONTAL / CHASIS - SUSPENSION AVANT / CHÂSSIS -

GABELFEDERUNG VORNE / CHASSIS -

10076

10124

10046

9239

9206

9219

9262

9271

9207

9211

9207

9209

10076

M4 x 4mm Set Screw

10044

M3 x 8mm CH Screw

10045

M3 x 10mm CH Screw

10046

M3 x 12mm CH Screw

10047

M3 x 14mm CH Screw

10082

M4 x 14mm CH Screw

10135

M4 x 10mm BH Screw

10068

M3 x 10mm BH Screw

10070

M3 x 14mm BH Screw

10081

M4 x 8mm CH Screw

10045

M3 x 10mm CH Screw

10126

10 x 6 x 3mm Bearing

10068

M3 x 10mm BH Screw

10087

M3 Lock Nut

10067

M3 x 8mm BH Screw

ASSEMBLY

Page is loading ...

Atomik-RC.Com

49

10070

10045

10136

10044

10068

9255

9260

9218

9261

9276

9273

9283

9282

10139

10047

10022

9257

10046

10082

10087

9224

10087

9286

REAR SUSPENSION - CHASSIS

SUSPENSIÓN TRASERA / CHASIS - SUSPENSION ARRIÈRE / CHÂSSIS -

HINTERE GABELFEDERUNG / CHASSIS -

SERVO - MOTOR

SERVO - MOTEUR - -

10082

M4 x 14mm CH Screw

10022

M3 x 20mm Set Screw

10139

M5 x 4mm Set Screw

10136

M4 x 12mm BH Screw

10070

M3 x 14mm BH Screw

10047

M3 x 14mm CH Screw

10044

M3 x 8mm CH Screw

10045

M3 x 10mm CH Screw

10068

M3 x 10mm BH Screw

10046

M3 x 12mm CH Screw

10087

M3 Lock Nut

ASSEMBLY

Page is loading ...

Atomik-RC.Com

51

10078

9245

9251

10079

10094

REAR SHOCK ABSORBER

AMORTIGUADOR TRASERO - AMORTISSEUR ARRIÈRE -

HINTERER STOßDÄMPFER -

10078

9246

9251

10079

10094

FRONT SHOCK ABSORBER

AMORTIGUADOR DELANTERO - AMORTISSEUR AVANT -

VORDERER STOßDÄMPFER -

10078

M3 x 24mm SH Screw

10079

M3 x 26mm SH Screw

10078

M3 x 24mm SH Screw

10079

M3 x 26mm SH Screw

10094

M3 Flanged Lock Nut

10094

M3 Flanged Lock Nut

ASSEMBLY

Page is loading ...

Atomik-RC.Com

53

PARTS

PIEZAS - PIÈCES - TEILE -

LIST

LISTA - LISTE -

9268 Ford Raptor SVT SCT Body - MMSCT

9269 3X17mm Pins (12pcs) - MMSCT

9270 3X15mm Pins (12pcs) - MMSCT

9271 2.5X11mm Pins (12pcs) - MMSCT

9272 2 Channel 2.4Ghz Transmitter - MMSCT

9273 3 Channel 2.4Ghz Receiver - MMSCT

9274 2 Channel 2.4Ghz Tx/Rx Set - MMSCT

9275 9KG Servo - MMSCT

9276 Brushless Motor 2400 KV - MMSCT

9277 70Amp 2-3S Waterproof Brushless ESC - MMSCT

9280 Tire/Insert Set (4pcs) - MMSCT

9281 Wheel/Tire/Insert Set (2)pcs) - MMSCT

9282 13T Pinion Gear - MMSCT

9283 Body Clips Small (6pcs) - MMSCT

9284 Body Clips Large (6pcs) - MMSCT

9285 Rear Body Mount Bracket - MMSCT

9286 Front Internal Body Mount - MMSCT

9287 Wheel Set (2) - MMSCT

10013 M3X3mm Set Screw (6pcs)

10014 M3X10mm Set Screw (6pcs)

10015 M3X20mm Set Screw (6pcs)

10020 M3X12mm SH Screws (6pcs)

10022 M3X16mm SH Screws (6pcs)

10023 M3X18mm SH Screws (6pcs)

10029 M3X40mm CH Screws (6pcs)

10044 M3X8mm CH Screws (6pcs)

10045 M3X10mm CH Screws (6pcs)

10046 M3X12mm CH Screws (6pcs)

10047 M3X14mm CH Screws (6pcs)

10067 M3X8mm BH Screws (6pcs)

10068 M3X10mm BH Screws (6pcs)

10069 M3X12mm BH Screws (6pcs)

10070 M3X14mm BH Screws (6pcs)

10071 M3X16mm BH Screws (6pcs)

10076 M4*4mm Set Screw (6pcs)

10078 M3X24 CH Screw (6pcs)

10079 M3X26 CH Screw (6pcs)

10080 M3X3.5 BH Screw (6pcs)

10081 M4X8 SH Screws (6pcs)

10082 M4X14 SH Screws (6pcs)

10083 M4X16 SH Screws (6pcs)

10084 M4X26 SH Screws (6pcs)

10087 M3 Locknut 6P

10094 M3 Flanged Nylon Locknut (6pcs)

10124 8X16X5mm Bearing (6pcs)

10125 15X21X4mm Bearing (6pcs)

10126 6X10X3mm Bearing (6pcs)

10135 M4X10mm BH Screws (6pcs)

10136 M4X12mm BH Screws (6pcs)

10137 M4X14mm BH Screws (6pcs)

10138 M4X26mm BH Screws (6pcs)

10139 M5 x 4mm Set Screw (6pcs)

0653 2-3 Cell LiPO Charger - MMSCT

15077 20C 3S 2700mAh 11.1V LiPO - EC5

Option Parts

9288 Aluminum Front Upper Suspension Plate - MMSCT

9289 Aluminum Steering Knuckle Set - MMSCT

9290 Aluminum Rear Hub Set - MMSCT

9291 Aluminum C-Hub Set - MMSCT

9292 Aluminum Front Shock Set - MMSCT

9293 Aluminum Rear Shock Set - MMSCT

9294 Aluminum Front Chassis Brace - MMSCT

9295 Aluminum Rear Chassis Brace - MMSCT

9297 Aluminum Front Suspension Arm Set - MMSCT

9298 Aluminum Rear Suspension Arm Set - MMSCT

9299 Option Front Universal Dogbones Set - MMSCT

9300 Option Rear Universal Dogbones Set - MMSCT

9301 Aluminum Front Body Mount - MMSCT

9302 Aluminum SCT Body Post Set - MMSCT

9303 Aluminum Option Front Shock Tower - MMSCT

9304 Aluminum Option Rear Shock Tower - MMSCT

9305 Hard Coated Steel Pinion - 12T - MMSCT

9306 Hard Coated Steel Pinion - 13T - MMSCT

9307 Hard Coated Steel Pinion - 14T - MMSCT

9205 Diff Gear Assembly (F/R) - MMSCT

9206 Diff Drive Cup - MMSCT

9207 Diff Case - MMSCT

9208 Diff Ring Gear (F/R) - MMSCT

9209 Diff Gear Set - MMSCT

9210 Diff Input Gear - MMSCT

9211 44T Spur Gear - MMSCT

9212 Diff Gearbox - MMSCT

9213 Front C-Hub - MMSCT

9214 Steering Knuckle - MMSCT

9215 Rear Hub Set - MMSCT

9216 Rear Arm Set - MMSCT

9217 Chassis Stiffener Set - MMSCT

9218 Receiver Box - MMSCT

9219 Center Diff Mount - MMSCT

9220 Front Arm Set - MMSCT

9221 Chassis - MMSCT

9222 Steering Cover Plate - MMSCT

9223 Front VCD Set - MMSCT

9224 Center Drive Shaft Set - MMSCT

9225 Rear Drive Shaft Set - MMSCT

9226 Rear Wheel Axle - MMSCT

9227 Rear Pin Block Set - MMSCT

9228 Front Pin Block Set - MMSCT

9229 Suspension Bushing Set - MMSCT

9230 Drive Cup - MMSCT

9231 Lower Hinge Pin Set - MMSCT

9232 Hinge Pin 71.3mm - MMSCT

9233 Servo Saver Arm Set - MMSCT

9234 Servo Saver Shaft Set - MMSCT

9235 Servo Saver Adjustment Set - MMSCT

9236 Front Sway Bar Assembly - MMSCT

9237 Rear Sway Bar Assembly - MMSCT

9238 Alloy Chassis Plate - MMSCT

9239 Rear Center Diff Mount - MMSCT

9240 Center Diff Support Plate - MMSCT

9241 Front Shock Tower - MMSCT

9242 Rear Shock Tower - MMSCT

9243 Steering Plate - MMSCT

9244 Wheel Hub Set - MMSCT

9245 Rear Shock Set - MMSCT

9246 Front Shock Set - MMSCT

9247 Rear Shock Spring - MMSCT

9248 Front Shock Spring - MMSCT

9249 Rear Shock Shaft - MMSCT

9250 Front Shock Shaft - MMSCT

9251 Shock Bushing Set - MMSCT

9252 Shock O-ring Set - MMSCT

9253 Front Upper Linkage Set - MMSCT

9254 Rear Linkage Set - MMSCT

9255 Servo Linkage - MMSCT

9256 Steering Linkage - MMSCT

9257 Pivot Ball Set - MMSCT

9258 Turnbuckle Set - MMSCT

9259 Center Diff Assembly - MMSCT

9260 Servo Arm - MMSCT

9261 Motor Mount - MMSCT

9262 Diff Pin Set - MMSCT

9263 Body Post - MMSCT

9264 Front Body Mount Set - MMSCT

9265 Rear Body Mount Set - MMSCT

9266 Front Bumper Set - MMSCT

9267 Rear Bumper Set - MMSCT

9268 Ford Raptor SVT SCT Body - MMSCT

9269 3X17mm Pins (12pcs) - MMSCT

9270 3X15mm Pins (12pcs) - MMSCT

9271 2.5X11mm Pins (12pcs) - MMSCT

9272 2 Channel 2.4Ghz Transmitter - MMSCT

9273 3 Channel 2.4Ghz Receiver - MMSCT

9274 2 Channel 2.4Ghz Tx/Rx Set - MMSCT

9275 9KG Servo - MMSCT

9276 Brushless Motor 2400 KV - MMSCT

9277 70Amp 2-3S Waterproof Brushless ESC - MMSCT

9280 Tire/Insert Set (4pcs) - MMSCT

9281 Wheel/Tire/Insert Set (2)pcs) - MMSCT

9282 13T Pinion Gear - MMSCT

9283 Body Clips Small (6pcs) - MMSCT

9284 Body Clips Large (6pcs) - MMSCT

9285 Rear Body Mount Bracket - MMSCT

9286 Front Internal Body Mount - MMSCT

9287 Wheel Set (2) - MMSCT

10013 M3X3mm Set Screw (6pcs)

10014 M3X10mm Set Screw (6pcs)

10015 M3X20mm Set Screw (6pcs)

10020 M3X12mm SH Screws (6pcs)

10022 M3X16mm SH Screws (6pcs)

10023 M3X18mm SH Screws (6pcs)

10029 M3X40mm CH Screws (6pcs)

10044 M3X8mm CH Screws (6pcs)

10045 M3X10mm CH Screws (6pcs)

10046 M3X12mm CH Screws (6pcs)

10047 M3X14mm CH Screws (6pcs)

10067 M3X8mm BH Screws (6pcs)

10068 M3X10mm BH Screws (6pcs)

10069 M3X12mm BH Screws (6pcs)

10070 M3X14mm BH Screws (6pcs)

10071 M3X16mm BH Screws (6pcs)

10076 M4X4mm Set Screw (6pcs)

10078 M3X24 CH Screw (6pcs)

10079 M3X26 CH Screw (6pcs)

10080 M3X3.5 BH Screw (6pcs)

10081 M4X8 CH Screws (6pcs)

10082 M4X14 CH Screws (6pcs)

10083 M4X16 CH Screws (6pcs)

10084 M4X26 CH Screws (6pcs)

10087 M3 Locknut 6P

10094 M3 Flanged Nylon Locknut (6pcs)

10124 8X16X5mm Bearing (6pcs)

10125 15X21X4mm Bearing (6pcs)

10126 6X10X3mm Bearing (6pcs)

10135 M4X10mm BH Screws (6pcs)

10136 M4X12mm BH Screws (6pcs)

10137 M4X14mm BH Screws (6pcs)

10138 M4X26mm BH Screws (6pcs)

10139 M5 x 4mm Set Screw (6pcs)

0653 2-3 Cell LiPO Charger - MMSCT

15077 20C 3S 2700mAh 11.1V LiPO - EC5

P/N Description - Descripción - Beschreibung -

P/N Option Parts - Piezas opcionales - Pièces optionnelles - Tuningteile -

9288 Aluminum Front Upper Suspension Plate - MMSCT

9289 Aluminum Steering Knuckle Set - MMSCT

9290 Aluminum Rear Hub Set - MMSCT

9291 Aluminum C-Hub Set - MMSCT

9292 Aluminum Front Shock Set - MMSCT

9293 Aluminum Rear Shock Set - MMSCT

9294 Aluminum Front Chassis Brace - MMSCT

9295 Aluminum Rear Chassis Brace - MMSCT

9297 Aluminum Front Suspension Arm Set - MMSCT

9298 Aluminum Rear Suspension Arm Set - MMSCT

9299 Option Front Universal Dogbones Set - MMSCT

9300 Option Rear Universal Dogbones Set - MMSCT

9301 Aluminum Front Body Mount - MMSCT

9302 Aluminum SCT Body Post Set - MMSCT

9303 Aluminum Option Front Shock Tower - MMSCT

9304 Aluminum Option Rear Shock Tower - MMSCT

9305 Hard Coated Steel Pinion - 12T - MMSCT

9306 Hard Coated Steel Pinion - 13T - MMSCT

9307 Hard Coated Steel Pinion - 14T - MMSCT

54

Atomik-RC.Com

9201

SET-UP SHEET

HOJA DE REGLAJE - FICHE DE RÉGLAGE DU VÉHICULE

EINRICHTBLATT -

Steering

Front Suspension

Camber Angle

Rear Suspension

Toe Angle

Sway Bar

Track Conditions

Rear Shocks

Front

9201

Atomik RC™ USA

14028 N. Ohio Street

Rathdrum, Idaho 83858 USA

Australia

PO Box 7325

Alexandria, NSW 2015

Customer Service

800.705.0620

208.762.0620 (Outside USA)

[email protected]

www.atomik-rc.com

0-14

www.facebook.com/AtomikRC www.twitter.com/Atomik_RCwww.pinterest.com/atomikrc www.youtube.com/theatomikrc

Atomik Atomik Metal Mulisha Brian Deegan 1:8 Ford Raptor 150 RC Truck Owner's manual

This manual is also suitable for

Atomik Atomik Metal Mulisha Brian Deegan 1:8 Ford Raptor 150 RC Truck Owner's manual

in other languages

Related papers

Other documents