Metra 99-7876 Installation guide

99-7876
Metra
Brand
Metra
Model
99-7876
Category
Mounting kits
Type
Installation guide

Metra 99-7876 is a car radio installation kit designed for specific Honda Pilot models, allowing you to seamlessly integrate an aftermarket radio into your vehicle while retaining essential features. With its ISO mount radio provision and included pocket, you can mount your new radio securely and maintain a clean, factory-like appearance. Additionally, the kit includes wiring and antenna connections to ensure compatibility with your vehicle's electrical system and provide clear audio reception.

Metra 99-7876 is a car radio installation kit designed for specific Honda Pilot models, allowing you to seamlessly integrate an aftermarket radio into your vehicle while retaining essential features. With its ISO mount radio provision and included pocket, you can mount your new radio securely and maintain a clean, factory-like appearance. Additionally, the kit includes wiring and antenna connections to ensure compatibility with your vehicle's electrical system and provide clear audio reception.

INSTALLATION INSTRUCTIONS FOR PART 99-7876
KIT FEATURES
• ISO Mount Radio Provision With Pocket
• A) Radio Housing • B) Radio Housing Brackets
Wiring & Antenna Connections (sold seperately)
• 70-1729 - Honda Harness 2008-up
• 40-HD10 - Honda Antenna Adapter 2006-up
KIT COMPONENTS
A
Small Flat Blade Screwdriver • Panel Removal Tool
• Phillips Screwdriver • Wire Cutters
1-800-221-0932
© COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
HONDA
Pilot 2009-11
B
99-7876
Dash Disassembly
- HONDA Pilot 2009-11 ... ........ ........ ....... ........ ........ . 1,2
Kit Preparation
.............. .... ........ ........ ....... . .....3
Kit
Assembly
- ISO Mount Radio Provision With Pocket .... ....... ........ ........ . .4
Final
Assembly . .............. .... ........ ........ ....... . .....5
TABLE OF CONTENTS
99-7876
*Note:
Refer also to the instructions included with the aftermarket radio.
99-7876 DASH DISASSEMBLY
HONDA PILOT 2009-11
A
C
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the right a/c vent
panel.
(Figure A)
3
Remove the (2) Phillips screws secur-
ing the pocket below the radio then
unclip and remove the pocket.
(Figure B)
4
Remove (4) Phillips screws securing
the radio, Unplug and remove the
radio.
(Figure C)
5
Unclip and remove the left a/c vent
panel surrounding the shifter.
(Figure A)
2
Continued on page 2.
B
99-7876 DASH DISASSEMBLY
HONDA PILOT 2009-11
2
Remove (4) Phillips screws securing
the factory climate control. Unplug
and remove factory climate control.
NO
TE: Retain (4) Phillips screws and
climate control for reuse in Kit
Assembly.
(Figure E)
7
Remove the (6) screws retaining the
(3) clip assemblies at the top edge of
the factory radio/climate control
assembly. Retain screws and clip
assemblies for reuse.
(Figure D)
6
Continue to kit preparation.
E
2
1 SCREW
ON EACH SIDE
1 SCREW
ON EACH SIDE
D
SIDE OF RADIO
REAR VIEW
3
99-7876 KIT PREPARATION
REAR VIEW RADIO HOUSING
A
B
HONDA PILOT 2009-11
*Note: Refer also to the instructions included with the aftermarket radio.
Attach the (3) clips removed in step 6
of the disassembly to the 99-7876 radio
housing using the factory hardware.
(Figure B)
2
Cut and remove support strut on radio
housing.
(Figure A)
1
Continue to kit assembly.
4
99-7876 KIT ASSEMBLY
ISO MOUNT RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
Position the aftermarket radio into
the radio housing and secure using
the hardware supplied with the radio.
(Figure C)
2
Attach the corresponding radio
housing bracket to the radio housing
(Figure A)
, then attach the climate
control to the assembly using the (4)
Phillips screws removed in step 7.
(Figure B)
1
A
B
C
Continue to final assembly.
99-7876 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’
s specifications.
5
99-7876 INSTRUCTIONS
1-800-221-0932
REV. 7/02/10 © COPYRIGHT 2008-2010 METRA ELECTRONICS CORPORATION INST99-7876
www.metraonline.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Metra 99-7876 Installation guide

99-7876
Metra
Brand
Metra
Model
99-7876
Category
Mounting kits
Type
Installation guide

Metra 99-7876 is a car radio installation kit designed for specific Honda Pilot models, allowing you to seamlessly integrate an aftermarket radio into your vehicle while retaining essential features. With its ISO mount radio provision and included pocket, you can mount your new radio securely and maintain a clean, factory-like appearance. Additionally, the kit includes wiring and antenna connections to ensure compatibility with your vehicle's electrical system and provide clear audio reception.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents