INSTRUCTIONS MANUAL
FOR VITROCERAMIC HOBS
H60ECSS
C60T125A5 15/7/03 07:24 Página 1
BET WITH US ON ECOLOGY. RECYCLE THE PACKAGING.
We contribute in the defence of the Environment.Thus, our
packagins:
• Are 100% recyclable.
• Contain the smaller quantity of parts and possible material
to facilitate thus the recycling.
3
C60T125A5 15/7/03 07:24 Página 3
4
CONTENTS
General description
............................................................5
Using the controls...................................................................6
Using pans..................................................................................7
Cleaning ................................................................................... 8
Connection Schema
............................................................. 9
Installation ....................................................................... 10,11
WARNING
Pot.max:
Type:
Voltage:
• Repair of any fault in your hob must be carried out only by an
Authorized Repair Service, otherwise the guarantee is not valid.
•Technical details and identification of the appliance are shown on
the specifications plate.
Consult this plate before procceding with electrical connection.
• Electrical connection must be carried out by a specialist, familiar
with the laws and official regulations recognized in each country.
Fill in the data table you will find below, with the data appearing on
the specifications plate, sticked on the hob.
w
Trade mark:
C60T125A5 15/7/03 07:24 Página 4
5
GENERAL DESCRIPTION
123456
REMARKS
LARGE HOTPLATE
(2,1 KW)
MEDIUM HOTPLATE
(1,7 KW)
SMALL HOTPLATE
(1,2 KW)
CONTROL SETTING
TYPE OF HOTPLATE
DIFFERENT
ELEMENTS COME
INTO PLAY
DEPENDING ON
SETTING
220 W 350 W 550 W 950 W 1.500 W 2.100 W
180 W 280 W 450 W 750 W 1.200 W 1.700 W
130 W 200 W 325 W 500 W 825 W 1.200 W
C60T125A5 15/7/03 07:24 Página 5
6
USING THE CONTROLS
Make sure that you turn on the right
knob for the heating zone you wish to
use.
As soon as a hotplate gets warm, the
corresponding residual heat warning
light will come on. After switching off,
the light will remain on until the
hotplate cools (about 30 minutes).
1
2
3
Turn the selector to the desired
seting: Setting 1: MINIMUM.
The ON light will come on.
C60T125A5 15/7/03 07:24 Página 6
7
USING PANS
Most stainless steel, enamel, iron,
ceramic and copper pans can be used
on vitroceramic hobs.
Aluminium pans are not recommended
as they may stain the vitreous surface,
unless they have stainless-steel covered
bottoms.
Hotplates should not be switched on
without a pan on top. The base of the
pan should be flat and dry. Pans that
have been used on gas cookers are not
normally flat enough and absorb heat
badly.
Make sure that the diameter of the pan
is at least that of the hotplate.
Avoid scarping pans over the
vitroceramic surface, as it may become
scratched. Lift always the pan.
Never use tinfoil or plastic containers.
They will melt and fuse permanently
with the vitroceramic surface.
SI
SATINLESS STEEL
ENAMEL
CERAMIC
COPPER
ALUMÍNIUM ALUMÍNIUM
SATINLESS STEEL
YES
C60T125A5 15/7/03 07:24 Página 7
8
IMPORTANT: If the vitroceramic surface breaks or you notice cracks in it, disconnect the hob.
Call your Repair Service.
CLEANING
Clean the vitroceramic surface
frequently, when it is cool. Never use
abrasive products or pads. Clean
with a damp cloth and soapy water.
Never use a steam cleaner.
Once a week, clean thoroughly with
specific products that preserve and
protect vitroceramic hobs (Sample in
accessory bag). Scrape off hard stuck
dirt with the scraper (Included in
accessory bag).
The manufacturer recommends
VITRO-CLEN for cleaning and
conserving your vitroceramic hob.
If sugar (or sugary matter) or plastic
is accidentally burnt on the hob,
remove it at once with the scraper
while it’s still hot. Otherwise they may
leave a pemanent mark.
Do not use the hob as a work surface.
Be particularly careful with dirt like
soil or dust from vegetables, cleaning
powders, etc. which may scratch the
surface when pans are slid over it.
INMEDIATELY
C60T125A5 15/7/03 07:24 Página 8
9
CONNECTION SCHEMA
Hob will make the connection according to the adjacent drawings. (The
cable must support temperatures of up to 120ºC).
The hotplate must be connected to the mainstrean with a plug that meets the
EEC 7 publication or with a multi-pole switch with a distance between the
open contacts of at least 3mm.
Total power
Hotplate: 60 cms., 6,3kW
This device conforms to European directives 73/23/CEE and 89/336/CEE
60 cms 220...240V~ 27,5 A 32 A 220...240V~ 14 A 16 A
Voltage Int.nominal Protection
by phases
Voltage Int.nominal Protection
by fases
PLATE
Three phase
60 cms 380...400V~ 11 A 12 A 380...400V~ 16 A 20 A
Voltage Int.nominal Protection
by phases
Voltage Int.nominal Protection
by phases
PLATE
Three phase
C60T125A5 15/7/03 07:24 Página 9
10
INSTALLATION
Place the hob face down on a
table. Remove the backing paper
and affix the sealing gasket all
round the perimeter. (fig.1)
When the plate comes without
frame, first stick on the shaped
strips as shown on the drawing
and then stick on the straight
strips adjusting them with the
previous ones. (fig.2).
1
2
Cut out a piece of the worktop following
the instructions on the template that
comes with the hob.
“X” type apparatus for degree of fire
protection.
Minimum distance between hole and
wall 100 m/m.
NOTE: DO NOT USE NON-REMOVABLE ELEMENTS WITH SILICONE.
fig.1
fig.2
C60T125A5 15/7/03 07:24 Página 10
11
INSTALLATION
3
Place the hob alongside the cavity in
the worktop and connect the power
cable to the electrical socket.
IMPORTANT: Carry out connection
with the power disconnected. There
must be a good grounding connection
and a switch must be provided in an
accessible place to isolate all phases,
with at least 3mm. clearance between
contacts. The manufacturer will not accept
responsability for installations carried out other
than as directed here.
The hob installation should be performed by a
technician certificated by the manufacturer.
4
Next insert the hob in the worktop
cavity, pressing down firmly to ensure a
good seal.
5
NOTE: This equipment complies with standard 82/499/CE on radio interferences.
Fix the 4 clamps underneath the hob to
the 4 corners of the cavity.
(Clamps, brackets and nuts are
supplied in acessory bag).
C60T125A5 15/7/03 07:24 Página 11
07-03
C60T125A5
Printer on recycled paper
Your 1
st
Year Guarantee
Yo ur appliance carries a 12 months parts and labour warranty. To fulfil the
conditions of your guarantee, the appliance must be correctly installed and
operated, in accordance with the instructions, and be only used for normal
domestic purposes.
Please note that the guarantee, and service availability, only apply to the
United Kingdom.
Customer Service
In case of difficulty please call the Customer Service Helpline on
01245 321111
Please ensure you have the model and serial number to hand when calling
customer service.
C60T125A5 15/7/03 07:24 Página 12
/