De Dietrich DTG796XA Owner's manual

Brand: De Dietrich

Model: DTG796XA

Category: Hobs

Type: Owner's manual

De Dietrich DTG796XA offers a variety of cooking options with its four burners, including an auxiliary burner, semi-rapid, rapid, and double crown burner. It features automatic ignition with safety valves and flame control system for added safety. The enamelled pan supports are removable for easy cleaning, and the stainless steel surface can be wiped clean with soapy water.

INSTRUCTIONS FOR THE INSTALLATION AND USE OF

BUILT-IN HOT PLATES

COD. 208318-00 - 15.10.2009

TABLE OF CONTENTS

GENERAL NOTICE pag.3 -

INSTRUCTION FOR THE USER -

Using the burners pag.4

Abnormal operation pag.5

Cleaning pag.6

INSTRUCTION FOR THE INSTALLER -

Installing the top pag.7

Fastening the top pag.7

Installation room pag.7

Gas connection pag.8

Electric connection pag.8

Replacing the nozzles pag.8

Adjusting the burners pag.9

Replacing the power supply cable pag.9

MODEL pag.10 -

TECHNICAL CHARACTERISTIC TABLES pag.11 -

SERVICE pag.11 -

WARRANTY pag.12 -

We invite you to read this instruction booklet carefully, before installing and using the equipment.

It is very important that you keep this booklet together with the equipment for any future

consultation.

If this equipment should be sold or transferred to another person, make sure that the new

user receives the booklet, so that he can learn how to operate the appliance and read the

corresponding notice.

This is a Class 3 appliance

The manufacturer refuses all responsibility for possible damages to things or people, resulting

from a wrong installation or from an improper, incorrect or unreasonable use of this equipment.

GENERAL NOTICE

This appliance complies with the following Directives:

EEC 2009/142/CE (Gas) EEC 2004/108/CE (Electromagnetic Compatibility)

2006/95/CE (Low Voltage) EEC 89/109 (Contact with foods)

The installation must be carried out by authorised personnel, in conformity with the regulations in force. -

This equipment has been designed to be used by adults. -

Therefore, make sure that children do not go near the equipment to play with it. -

This appliance is not intended for use by young children or infirm persons unless they have been -

adequately supervised by a responsible person to ensure that they can use the appliance safely.

Before powering the equipment, check that it is properly adjusted for the type of gas at disposal (see the -

“installation” paragraph).

Before carrying out the maintenance or cleaning the equipment, cut power supply off and make it cool -

down.

Make sure that air circulates around the gas equipment. Insufficient ventilation produces a lack of oxygen. -

In case of an intense or prolonged use of the equipment, it may be necessary to improve aeration, for -

example by opening a window or increasing the mechanical suction power, if it exists.

The products of combustion must be discharged outside through a suction hood or an electric fan (see the -

“installation” paragraph).

For any possible operation or modification, apply to an authorized Technical Assistance Centre and -

demand original spare parts.

Where this appliance is installed in marine craft or in caravans, it shall not be used as a space heater. -

Not for use in marine craft, caravans or mobile homes unless each burner is fitted with a flame -

safeguard.

DO NOT MODIFY THIS APPLIANCE.

Servicing shall be carried out only by authorised personnel.

The product label, with the serial number, is sticked under the hob.

INSTRUCTIONS FOR THE USER

It is necessary that all the operations regarding the installation, adjustment and

adaptation to the type of gas available are carried out by qualified personnel, in

conformity with the regulations in force.

The specific instructions are described in the booklet section intended for the

installer.

USING THE BURNERS

The symbols silk-screen printed on the side of the

knob indicate the correspondence between the

knob and the burner.

Automatic start-up with valves

To light the burners, press the corrisponding control

knob down and hold it down while turning anti-

clockwise until it reaches the maximum position

(large flame, fig.1 / 1A).

Fig. 1

Fig. 1/A

Once the burner has been started up, keep the

knob pressed for about 6 seconds.

Using the burners

In order to obtain the maximum yield without waste

of gas, it is important that the diameter of the pot is

suitable for the burner potential (see the following

table), so as to avoid that the flame goes out of the

pot bottom (fig. 2).

Fig. 2

Use the maximum capacity to quickly make the

liquids reach the boiling temperature, and the

reduced capacity to heat food or maintain boiling.

All of the operating positions must be chosen

between the maximum and the minimum ones,

never between the minimum position and the

closing point.

The gas supply can be interrupted by turning the

knob clockwise up to the closing position.

If there is no power supply, it is possible to light the

burners with matches, setting the knob to the start-

up point (large flame, fig.1/1A).

BURNERS

Power (MJ/h)

Ø of pots

NG LPG

Auxiliary 3,3 3,5 10 - 14 cm

Semi-rapid 6,2 5,5 16 - 18 cm

Rapid 12,0 9,4 20 - 22 cm

Double crown 16 14.6 24 - 26 cm

Notice

When the equipment is not working, always check -

that the knobs are in the closing position (see

fig.1).

If the flame should blow out accidentally, the safety -

valve will automatically stop the gas supply, after a

few seconds. To restore operation, set the knob to

the lighting point (large flame, fig. 1) and press.

While cooking with fat or oil, pay the utmost -

attention as these substances can catch fire when

overheated.

Do not - spray aerosols in the vicinity of the

appliance while it is in operation.

Do not store or use flammable liquids or items in -

the vicinity of this appliance.

Close position

Maximum

position

Minimum

outer and

inner position

Close position

Maximum

inner

position

Minimum

inner

position

Maximum outer and

inner position

Minimum

position

INSTRUCTIONS FOR THE USER

Do not place unstable or deformed pots on the -

burner, so as to prevent them from overturning or

overflowing.

Make sure that pot handles are placed properly. -

When the burner is started up, check that the -

flameis regular and, before taking pots away,

always lowerthe flame or put it out.

ABNORMAL OPERATION

Any of the following are considered to be abnormal

operation and may require servicing:

Yellow tipping of the hob burner flame. -

Sooting up of cooking utensils. -

Burners not igniting properly. -

Burners failing to remain alight. -

Burners extinguished by cupboard doors. -

Gas valves, which are difficult to turn. -

In case the appliance fails to operate correctly, -

contact the authorised service provider in your

area.

Do not place anything, e.g. flame

tamer, asbestos mat, between pan

and pan support as serious damage

to the appliance may result

Do not remove the pan support and

enclose the burner with a wok stand

as this will concentrate and deflect

the heat onto the hotplate.

Do not use large pots or heavy

weights which can bend the pan

support or deflect the flame onto

the hotplate.

Locate pan centrally over the

burner so that it is stable and does

not overhang the appliance.

Use only a wok support supplied

o r r e c o m m e n d e d b y t h e

manufacturer of the appliance.

INSTRUCTIONS FOR THE USER

MAINTENANCE SCHEDULE

Clean the appliance regularly, preferably after

each use. This will help to prevent grease and

other deposits adhering to surfaces and becoming

difficult to remove.

CLEANING

Before any operation, disconnect the appliance

from the electric grid. Don’t use a steam

cleaner for the cleaning the hob.

It is advisable to clean the appliance when it is

cold.

Enamelled parts

The enamelled parts must be washed with a

sponge and soapy water or with a light detergent.

Do not use abrasive or corrosive products.

Do not leave substances, such as lemon or tomato

juice, salt water, vinegar, coffee and milk on the

enamelled surfaces for a long time.

Stainless steel an alluminum parts

Stainless steel can be stained if it remains in

contact with highly calcareous water or aggressive

detergents for an extended period of time.

The stainless steel parts should also be cleaned

with soapy water and then dried with a soft cloth.

Burners and racks

These parts can be removed to make cleaning

easier.

The burners must be washed with a sponge and

soapy water or with a light detergent, wiped well

and placed in their housing perfectly.

Make sure that the flame-dividing ducts are not

clogged.

Check that the feeler of the safety valve and the

start-up electrode are always perfectly cleaned, so

as to ensure an optimum operation.

The racks can be washed in the dishwasher.

Gas taps

The possible lubrication of the taps must be carried

out by specialized personnel, exclusively.

In case of hardening or malfunctions in the gas

taps, apply to the Customer Service.

Pan Support

After removing the pan supports or cleaning,

ensure they are placed back in the correct centred

and stable position.

Also ensure pan supports are positioned as shown

below. The larger spaced fingers should be

positioned over the Triple Crown and Rapid

burner.

RAPID

INSTALLATION

Installing the top

The appliance is designed to be embedded into

heat-resistant pieces of furniture.

The walls of the pieces of furniture must resist a

temperature of 75°C besides the room one.

The equipment must not be installed near

inflammable materials, such as curtains, cloths,

etc. Make a hole in the top of the piece of furniture,

with the dimensions indicated in fig. 3, at a distance

of at least 50 mm from the appliance border to the

adjacent walls.

MODEL L (mm) P (mm)

DTG796XA 865 480

Any possible wall unit over the cook-top must be

placed at a distance of at least 760 mm from the

top.

It is advisable to isolate the appliance from the

piece of furniture below with a separator, leaving a

depression space of at least 10 mm (fig. 4).

The rear wall should be a suitable non combustible

material for a height of 150 mm above the hob

surface for the entire width of the hob. Any side

wall surface situated within 200 mm from the

edge of any hob burner must be suitable non-

combustible material for the height of 150 mm for

the entire depth of the hob.

If the hob is going to be installed on the top of an

oven, precautions must be taken to guarantee an

installation in accordance with current accident

prevention standards. Pay particular attention to

the position of the electric cable and gas pipe: they

must not touch any hot parts of the oven.

Moreover, if the hob is going to be installed on

the top of a built in oven without forced cooling

ventilation, proper air vents must be installed to

guarantee an adequate ventilation, with the lower

air entering with a cross section of at least 200cm

and the higher air exiting with a cross section of at

least 60 cm

Fastening the top

Every cook-top is equipped with a special washer.

A set of hooks is also supplied for mounting the

cook-top.

For the installation proceed as follows:

Remove the racks and burners from the top. -

Turn the appliance upside down and lay the -

washer S along the external border (fig. 5).

Fig.5 Fig.6

Introduce and place the cook-top in the hole made -

in the piece of furniture, then block it with the V

screws of the fastening hooks G (fig.6).

Installation room

This appliance is not provided with a device for

exhausting the products of combustion.

Therefore, it is necessary to discharge these

smokes outside.

The room where this appliance is installed

must ave a natural air inflow, so as to ensure a

regular gas combustion and room ventilation: the

INSTRUCTIONS FOR THE INSTALLER

IMPORTANT NOTICE:

THE OPERATIONS INDICATED BELOW MUST BE FOLLOWED BY AUTHORISED

PERSONNEL EXCLUSIVELY, IN CONFORMITY WITH THE REGULATIONS IN FORCE.

THE MANUFACTURING FIRM REFUSES ALL RESPONSIBILITY FOR DAMAGES TO

PEOPLE, ANIMALS OR THINGS, RESULTING FROM THE FAILURE TO COMPLY WITH

SUCH PROVISIONS.

THIS APPLIANCE SHALL BE INSTALLED ONLY BY AUTHORISED PERSONS AND IN

ACCORDANCE WITH THE MANUFACTURER’S INSTALLATION INSTRUCTIONS, LOCAL

GAS FITTING REGULATIONS, MUNICIPAL BUILDING CODES, ELECTRICAL WIRING

REGULATIONS, AS 5601 - GAS INSTALLATIONS AND ANY OTHER STATUTORY

REGULATIONS

Fig.3

Fig.4

necessary air volume must not be lower than 20m

Air must come from permanent openings made on

the room walls that communicate with the outside.

The section of these openings shall correspond to

at least 200 cm

Gas connection

Make sure that the appliance is adjusted for

the gas type available (see the label under the

appliance). Follow the instructions indicated in the

chapter “gas transformations and adjustments” for

the possible adaptation to different gases.

There are two ways to carry out the connection to

the main gas line:

A. The hotplate can be connected with rigid pipe as

specified in AS5601 table 3.1.

B. The hotplate can be connected with a Flexible

Hose, which complies with AS/NZS 1869 (AGA

Approved), 10mm ID, class B or D, no more than

1.2m long and in accordance with AS5601.

The hose assembly shall be suitable for connection

to a fixed consumer piping outlet located at a point

800mm to 850mm above the floor and in a region

outside the width of the appliance to a distance of

250mm.

Ensure that the Hose does not contact the hot

surfaces of the hotplate, oven, dishwasher or other

appliance that may be installed underneath or next

to the hotplate. WARNING: Ensure that the hose

assembly is restrained from accidental contact

with the flue or flue outlet of an underbench oven.

The hose should not be subjected to abrasion,

kinking or permanent deformation and should

be able to be inspected along its entire length.

Unions compatible with the hose fittings must be

used and connections tested for gas leaks. The

supply connection point shall be accessible with

the appliance installed.

Please select the type which is correct for the

supply concerned.

Once the installation is complete, check all

connections for gas leaks with soap and water.

DO NOT use a naked flame for detecting leaks.

Ignite all burners both individually and concurrently

to ensure correct operation of gas valves, burners

and ignition. Turn gas taps to low flame position

and observe stability of the flame for each burner

individually and concurrently. When satisfied with

the hotplate, please instruct the user on the correct

method of operation. In case the appliance fails

to operate correctly after all checks have been

carried out, refer to the authorised service provider

in your area.

Electric connection

The connection to the electric grid must be carried

out by qualified personnel and in conformity with

the regulations in force.

The voltage of the electric system must correspond

to the value indicated in the label under the

appliance. Make sure that the electric system is

provided with an effective ground connction in

compliance with the regulations and provisions of

the law. Grounding is compulsory.

GAS TRANSFORMATIONS AND ADJUSTMENTS

Data Label

A duplicate Data Label is supplied to adhere in an

accessible area next to the appliance.

This appliance is suitable for Natural Gas and

Universal LPG; ensure that the available gas supply

matches the Data Label.

When converting from Natural Gas to Universal

LPG ensure that the NG regulator is removed

and replaced with the Test Point Assembly. An

AGA Approved gas regulator suitable for a supply

pressure of 2.75 kPa should be part of the gas

tank supply and the test point pressure should be

adjusted to 2.75 kPa.

Replacing the nozzles

If the equipment is adjusted for a type of gas that is

different from the one available, it is necessary to

replace the burner nozzles.

The choice of the nozzles to replace must be

made according to the table of the “technical

characteristics” as enclosed.

Act as follows:

Remove the racks and burners. -

By means of a straight spanner L, unscrew the -

nozzle U or U1,U2 (fig.7 - 7/A) and substitute it

with the corresponding one.

Tighten the nozzle strongly. -

N.B.: for the burner double crown don’t close

with excessive force the nozzles U2.

Fig. 7 Fig. 7/A

INSTRUCTIONS FOR THE INSTALLER

Adjusting the burners

The lowest flame point must always be properly

adjusted and the flame must remain on even if

there is an abrupt shift from the maximum to the

minimum position.

If this is not so, it is necessary to adjust the lowest

flame point as follows:

start the burner up; -

turn the tap up to the minimum position (small -

flame);

remove the knob from the tap rod; -

introduce a flat-tip screwdriver in the hole of control -

panel of the tap (fig. 8) and turn the by-pass screw

F (fig.8/A-8/B) up to a proper adjustment of the

lowest flame point. See setting below.

Fig.8 Fig.8/A

Fig.8/B

As regards LPG gas burners, the by-pass screw

must be tightened completely.

For Natural Gas the bypass screws should be set

as follows:

Auxiliary: 3/8 turn anticlockwise from fully

closed position

Semi-Rapid: 3/8 turn anticlockwise from fully

closed position

Rapid: 3/8 turn anticlockwise from fully

closed position

Double

Crown:

7/8 for outer wok

3/8 for inner wok

MAINTENANCE

Replacing the power supply cable

If the power supply cable should be replaced,

it is necessary to use a cable with a section of

3x0.75mm

type H05VV-F or H05RR-F, complying

with the regulations in force.

The connection to the terminal board must be

effected as shown in fig.9:

brown cable L (phase)

blue cable N (neutral)

green-yellow cable

(ground)

Fig.9

INSTRUCTIONS FOR THE INSTALLER

DTG796XA

Gas Connection

Electrical Supply

Cord

260

900

510

MODEL

NG Universal LPG

1 Rapid burner 12,0 MJ/h 9,4 MJ/h

2 Semi-rapid burner 6,2 MJ/h 5,5 MJ/h

3 Auxiliary burner 3,3 MJ/h 3,5 MJ/h

4 Triple ring burner 16,0 MJ/h 14,6 MJ/h

8 Control knob for burner

TEST POINT PRESSURE

The appliance is factory set for Natural gas. The test point pressure should be adjusted to 1.00 kPa with

the following burners operating at maximum rate:

Semi-Rapid and Rapid when using the Bromic BM-WF-1A (NG) Regulator;

Semi-Rapid when using the Beckley 2300 Series Regulator

INSTRUCTIONS FOR THE INSTALLER

TECHNICAL CHARACTERISTIC TABLES

BURNERS

GAS

NORMAL

PRESSURE

INJECTOR

DIAMETER

TAPE BY

PASS

DIAMETER

NOMINAL

HEAT INPUT

(MJ/h)

N° DESCRIPTION KPa 1/100 mm 1/100 mm (*)

1 RAPID

Universal LPG 2.75 85 42 9.4

Natural 1.00 155 3/8 12.0

2 SEMI-RAPID

Universal LPG 2.75 65 31 5.5

Natural 1.00 110 3/8 6.2

3 AUXILIARY

Universal LPG 2.75 52 27 3.5

Natural 1.00 80 3/8 3.3

DOUBLE

CROWN

Universal LPG 2.75

50 27

14.6

68 60

Natural 1.00

75 3/8

130 7/8

(*) By-pass screw is fully closed for Universal LPG;

(*) Numbers of turns by-pass screw is adjusted from fully closed for Natural Gas

SERVICE

For Authorised service and spare parts contact:

Hagemeyer Brands Australia Pty Ltd

Head Office: 104 Vanessa St, Kingsgrove NSW 2208 Australia

TEL: 1300 553 720

FAX: 1300 553 719

1. Subject to the “Statement of Standard Warranty

Conditions” this product is covered by the following

Warranty:

TWO (2) YEARS WARRANTY from date of

purchase, covering all parts and labour.

2. The appliance is warranted under normal single

family domestic installation and use, as set out in

the user manual, against manufacturing defects for

the Warranty periods shown above.

3. Should service be required under this Warranty,

the purchaser should contact an approved DE

DIETRICH Service Provider during their normal

business hours.

4. At no time does DE DIETRICH have liability

for any freight or transportation costs or for any

damage during transit or for any consequence

of failure of this appliance outside of the normal

service area, unless such limitation of liability is

prohibited by statute.

5. This Warranty excludes replacement of parts

required due to normal wear and tear including

light globes.

6. This Warranty only applies, provided the

appliance has been used in accordance with

the manufacturer’s instructions and provided

an accident, misuse, neglect or abuse has not

damaged the appliance.

7. None of the above Warranties purport to

exclude, restrict or modify either the application or

the exercise of a right conferred by any applicable

Statute.

8. Please complete the details below, which should

be retained for future reference along with your

proof of purchase:

Date of Purchase: ……………………………..

Model No: ……………………………………….

Serial No: ………………………………………..

Notice to Victorian Customers from the

Victorian Plumbing Industry Commission.

This product must be installed by a licensed person

as required by the Victorian Building Act 1993.

Only a licensed person will give you a Compliance

Certificate, showing that the work complies with

all the relevant standards. Only a licensed person

will have insurance protecting their workmanship

for 6 years. Make sure you use a licensed person

to install this product and ask for your Compliance

Certificate.

Distributed by MEA (A Divisions of Hagemeyer Brands Australia)

FOR AUSTRALIAN CUSTOMERS ONLY

DE DIETRICH

PRODUCT WARRANTY

STATEMENT OF STANDARD

WARRANTY CONDITIONS

1. The Warranty only applies provided that the

appliance has been used in accordance with the

manufacturer’s instructions and provided that the

appliance has not been damaged by an accident,

misuse, neglect or abuse of any person other than

the manufacturer or MEA or from faulty installation,

mis-adjustment or tampering by unauthorised

persons.

2. When a service inspection reveals the alleged

fault or faults are caused by incorrect operation,

contrary to the instruction manual, and otherwise

the appliance is in good order and working

condition, the purchaser shall be liable for a

service fee charged by MEA or one of its’ Service

Providers.

3. If the appliance is used in Commercial

Applications or for Rental purposes, a separate

warranty of Twelve (12) months covering all parts

with Three (3) months on the labour will apply.

4. Subject to the provisions of any applicable

statute this Warranty applies to the original retail

purchaser only and is not transferable.

5. Subject to the provisions of any applicable

statute, at no time does MEA have liability for

freight, transport or travel costs outside normal

service areas.

6. None of the above Warranties purport to

exclude, restrict or modify either the application or

the exercise of a right conferred by any applicable

statute.

7. Subject to any Warranties implied by statute, at

no time will MEA or its’ Service Providers be liable

for any economic loss consequent upon the failure

of the appliance.

8. This Warranty is only valid for De Dietrich major

appliances imported and distributed by MEA,

purchased and used in Australia.

The manufacturing firm refuses all responsibility for any possible imprecision in this booklet, due to

misprints or clerical errors. It reserves the right to make all the changes that it will consider necessary in

its own products, without effecting the essential characteristics of functionality and safety.

De Dietrich DTG796XA Owner's manual

Brand: De Dietrich

Model: DTG796XA

Category: Hobs

Type: Owner's manual

Download PDF

report

De Dietrich DTG796XA Owner's manual

De Dietrich DTG796XA Owner's manual

Related papers

Other documents