Terzismo BEL WD 14v User manual

Brand: Terzismo

Model: BEL WD 14v

Category: Washing machines

Type: User manual

CHAPTER

INDEX

Introduction

General points on delivery

Guarantee

Safety Measures

Technical Data

Setting up and Installation

Control Description

Table of Programmes

Selection

Detergent drawer

The Product

Washing

Drying

Automatic washing/drying cycle

Cleaning and routine maintenance

Faults Search

INTRODUCTION

Thank you for buying this high quality appliance from us

We would like to congratulate you on choosing this

appliance, and hope you find it to be an attractive and

beneficial addition to your home.

This handbook is designed to help you through each step of

owning your new appliance, from installation, to use.

Please read through all of this guide carefully before you

start using your appliance, as we have endeavoured to

answer as many questions as possible, and provide you with

as much support as we can.

If, however, you should find something missing, or not

covered, please contact the Belling Customer Care team

who will be only too happy to assist you on:

0871 22 22 503

In addition you could always try the website for frequently

asked questions and more Customer Care information.

Our policy is one of constant development and

improvement,therefore we cannot guarantee the strict

accuracy of all of our illustrations and specifications -

changes may have been made subsequent to publishing.

CUSTOMER CARE INFORMATION

If you should experience problems while operating the

appliance please refer to Chapter 15 – Faults search. If the

answer to the problem is not covered please call the

Customer Care Centre number listed above.

Your appliance is covered by a 12 month manufacturers

guarantee. If you experience problems within the first year

from the date of purchase a service engineer will be sent to

resolve the problem without charge. In order to prove the

age of the product please retain your purchase receipt.

CHAPTER 2

GUARANTEE

The appliance is supplied with a manufacturers 12 month

guarantee. Please retain your purchase receipt.

This should be kept in a safe place and presented to the

engineer if a service call is required.

CHAPTER 1

GENERAL POINTS ON DELIVERY

On delivery, check that the following are included with the

machine:

A) INSTRUCTION MANUAL

B) PLUGS

C) BEND FOR OUTLET TUBE

D) LIQUID DETERGENT OR LIQUID BLEACH

COMPARTMENT (CONTAINER)

KEEP THEM IN A SAFE PLACE

Check that the machine has not incurred damage during

transport. If this is the case, contact your nearest Technical

Assistance Centre.

CHAPTER 3

SAFETY MEASURES

IMPORTANT:

FOR ALL CLEANING AND MAINTENANCE WORK

● Remove the plug

● Turn off the water inlet tap.

● All Belling appliances are earthed. Ensure that the main

electricity circuit is earthed. Contact a qualified electrician if

this is not the case.

Appliance complies with European Directives

73/23/EEC and 89/336/EEC, replaced by 2006/95/EC and

2004/108/EC, and subsequent amendments.

● Do not touch the appliance with wet or damp hands or

feet.

WARNING: DURING THE WASHING CYCLE, THE WATER

CAN REACH A TEMPERATURE OF 90°C.

● Before opening the washing machine door, ensure that

there is no water in the drum.

● Do not use extension leads or multiple plugs.

● This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

● Do not pull the mains lead or the appliance itself to

remove the plug from the socket.

● Do not leave the appliance exposed to atmospheric

conditions (rain, sun etc.)

● In the case of removal,never lift the appliance by the

knobs or detergent drawer.

● During transportation do not lean the door against the

trolley.

Important!

When the appliance location is on carpet floors, attention

must be paid so as to ensure that there is no obstruction to

the bottom vents.

● Lift the appliance in pairs as illustrated in the diagram.

● In the case of failure and/or incorrect operation,turn the

washing machine off,close the water inlet tap and do not

tamper with the appliance. Contact a Technical Assistance

Centre for any repairs and ask for original spare parts.

Avoidance of these norms may compromise the safety of

the appliance.

● Should the supply cord (mains cable) be damaged,this is

to be replaced by a specific cable available from the after

sales service centre.

CHAPTER 5

SETTING UP INSTALLATION

Move the machine near its permanent position without the

packaging base.

Cut tube-holding straps.

Remove the 3 fixing screws marked (A) and remove the 3

spacers marked (B)

Remove the screw (C).

A spacer will fall inside the machine.

By tilting the machine, remove the above mentioned spacer.

Stop the holes using the plugs that you will find inside the

bag containing the instruction booklet.

WARNING:

DO NOT LEAVE THE PACKAGING IN THE REACH OF

CHILDREN AS IT IS A POTENTIAL SOURCE OF DANGER.

CHAPTER 4

MAXIMUM WASH LOAD DRY

POWER INPUT

ENERGY CONSUMPTION (PROG. 90°C)

FUSE RATING

SPIN

WATER PRESSURE

SUPPLY VOLTAGE

TECHNICAL DATA

2150

1,8

230

kWh

MPa

82 cm

60 cm

54 cm

1400

DRYING

r.p.m.

WASHING

min. 0,05

max. 0,8

Use the 4 feet to level the machine with the floor:

a) Turn the nut clockwise to release the screw adjuster of the

foot.

b) Rotate foot to raise or lower it until it stands firmly on the

ground.

c) Lock the foot in position by turning the nut anti-clockwise

until it comes up against the bottom of the machine.

Ensure that the knob is on the “OFF” position and the load

door is closed

Insert the plug.

After installation, the appliance must be positioned so that

the plug is accessible.

min 50 cm

max 85 cm

+2,6 mt max

max 100 cm

min 4 cm

Fix the sheet of corrugated material on the bottom as shown

in picture.

Connect the fill hose to the tap.

The appliance must be connected to the water mains using

new hose-sets.The old hose-sets should not be reused.

IMPORTANT:

DO NOT TURN THE TAP ON AT THIS TIME.

Position the washing machine next to the wall. Hook the

outlet tube to the edge of the sink paying attention that

there are no bends or restrictions along the tube.

It is better to connect the discharge hose to a fixed outlet of

a diameter greater than that of the outlet tube and at a

height of min. 50 cm. If is necessary to use the plastic sleeve

supplied.

The appliance must not be installed behind a lockable door,

a sliding door or a door with a hinge on the opposite side to

that of the washer dryer.

Please refer to diagrams below for various installation

options.

CHAPTER 6

CONTROLS

REMO

VING THE PLUG:

If your appliance has a non-rewireable moulded plug and you should wish to re-route the

mains cable through partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-wireable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible without moving the appliance.

DISPOSING OF THE PLUG:

Ensure that before disposing of the plug itself, you make the pins unusable so that it cannot be

accidentally inserted into a socket.

INSTRUCTIONS FOR CONNECTING CABLE TO

AN ALTERNATIVE

PLUG:

Important: the wires in the mains lead are coloured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not correspond with the coloured markings

identifyng the terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or or coloured Green or Green &

Yellow. Connect Brown wire to terminal marked L or coloured Red.

Connect Blue wire to terminal marked N or coloured Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse either in the plug or

adaptor or at the distribution board. If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

HOW TO CONNECT AN ALTERNATIVE PLUG:

The wires in this mains lead are coloured in accordance with the following code:

BLUE NEUTRAL(N)

BROWN LIVE(L)

GREEN&YELLOW EARTH(E)

DISPOSING OF THE APPLIANCE:

When disposing of the appliance please remove the plug by

cutting the mains cable as close as possible to the plug body

and dispose of it as described above.

ILNOP A

Door open button

Programme selector with “OFF” position

"Door Security" indicator light

"Delay Start" button

"Time countdown system" and “Delay Start” indicator lights

"Spin Selection" button

Spin speed indicator light

"Super Rapid" button

"Extra Rinse" button

"Drying Selection" button

Drying programme indicators

"Cold Wash" button

“Crease Guard” button

"Start/Pause" button

Buttons indicator light

Detergent drawer

DELAY START BUTTON

Appliance start time can be set with this button, delaying the

start by 3, 6 or 9 hours.

Proceed as follows to set a delayed start:

Select a programme (“STOP” indicator light blinks)

Press "Delay Start" button (each time the button is pressed the

start will be delayed by 3, 6 or 9 hours respectively and the

corresponding light will blink).

Press "Start/Pause" to commence the Delay Start operation

(the indicator light associated with the selected Delay Start

time stops blinking and remains ON).

At the end of the required time delay the programme will

start.

To cancel the Delay Start function :

press the "Delay Start" button until the indicator lights will be

off (The "STOP" light blinks) and the programme can be

started manually using the "Start/Pause" button or switch off

the appliance by turning the programme selector to "OFF"

position.

WARNING: IF THERE IS ANY BREAK IN THE POWER

SUPPLY WHILE THE MACHINE IS OPERATING, A SPECIAL

MEMORY STORES THE SELECTED PROGRAMME AND,

WHEN THE POWER IS RESTORED, IT CONTINUES WHERE IT

LEFT OFF.

TIME COUNTDOWN SYSTEM INDICATOR LIGHTS

In order to better manage your time, this washing machine

features an indicator light system that keeps you constantly

informed on the remaining cycle time.

Indicator light 90:

Remaining time above 60 minutes

Indicator light 60:

Remaining time less than 60 minutes

Indicator light 30:

Remaining time less than 30 minutes

Indicator light 15:

Remaining time less than 15 minutes

Indicator light Stop:

End of the programme.

1 min.

DESCRIPTION OF CONTROL

DOOR OPEN BUTTON

IMPORTANT:

A SPECIAL SAFETY DEVICE PREVENTS THE DOOR FROM

OPENING AT THE END OF THE WASH/SPIN CYCLE. AT THE

END OF THE SPIN PHASE WAIT UP TO 1 MINUTE BEFORE

OPENING THE DOOR.

PROGRAMME SELECTOR WITH OFF POSITION

ROTATES IN BOTH DIRECTIONS.

THE MACHINE IS TURNED ON BY SELECTING A

PROGRAMME VIA THE PROGRAMME SELECTOR.

THIS STATUS WILL BE INDICATED BY THE STOP

INDICATOR LIGHT FLASHING, THIS LIGHT WILL

CONTINUE TO FLASH UNTIL THE MACHINE HAS STARTED

OR THE MACHINE IS RETURNED TO THE OFF POSITION.

Press the "Start/Pause" button to start the selected cycle.

The programme carries out with the programme selector

stationary on the selected programme till cycle ends.

Switch off the washing machine by turning the selector to OFF.

NOTE:

THE PROGRAMME SELECTOR MUST BE RETURN TO THE

OFF POSITION AT THE END OF EACH CYCLE OR WHEN

STARTING A SUBSEQUENT WASH CYCLE PRIOR TO THE

NEXT PROGRAMME BEING SELECTED AND STARTED.

DOOR LOCKED INDICATOR

The “Door Locked” indicator light is illuminated when the door

is fully closed and the machine is ON.

When START is pressed on the machine with the door closed

the indicator will flash momentarily and then illuminate.

If the door is not closed the indicator will continue to flash.

A special safety device prevents the door from being opened

immediately after the end of the cycle.Wait for 1 minute after

the wash cycle has finished and the Door Locked light has

gone out before opening the door. At the end of cycle turn

the programme selector to OFF.

DRYING SELECTION BUTTON

With the programme selector not in the OFF position, press

the button to select the required drying programme; an

indicator will light to display the drying result selected each

time you press the button.

To cancel the selection before the start of a drying

programme, press the button repeatedly until the indicators

go out or return the programme selector to the OFF position.

To cancel the cycle during the drying phase, hold the button

down for 2 seconds until the cooling indicator lights up; given

the high temperature inside the drum, we recommend that

you allow the dryer to complete the cool down period

before returning the programme selector to the OFF position

and removing the laundry.

DRYING PROGRAMME INDICATORS

The indicators display the type of programme and/or drying

time:

utomatic Programmes: By selecting one of these 3

automatic programmes, the washer-dryer will calculate the

time needed for drying and the residual dampness required,

according to the load and drying type selected.

After pressing the START button, one of the indicators will light

to display the drying time remaining.

= Extra dry drying programme (recommended for

towels, bathrobes and bulky loads)

= Cupboard dry drying programme

= Iron dry drying programme

USEFUL TIPS:

The 30 minute drying programme is recommended for small

loads (less than 1 kg) or slightly damp loads.

Your washer-dryer ends the cycle automatically when it

reaches the drying level selected.

For the correct operation of the appliance, it is preferable

not to interrupt the drying phase unless it is really necessary.

Timed programmes:

120 minutes – 90 minutes – 60 minutes – 30 minutes:

Dual function indicators:

If one of the 3 automatic drying programmes is selected, the

indicators display the drying time remaining

They may be used to select timed drying programmes.

Cool down phase :

Switched on during the final cool down period, in the last 10

minutes of each drying phase.

COLD WASH BUTTON

By pressing this button it is possible to transform every

programme into a cold washing one,without modifying

other characteristics (water level,times, rythmes, etc...).

Curtains, small carpets, man made delicate fabrics, non

coulor fast garments can be safely washed thanks to this

new device.

SPIN SELECTION BUTTON

The spin cycle is very important to remove as much water as

possible from the laundry without damaging the fabrics.You

can adjust the spin speed of the machine to suit your needs.

By pressing this button, it is possible to reduce the maximum

speed, and if you wish, the spin cycle can be cancelled.To

reactivate the spin cycle press the button until you reach the

spin speed you would like to set. To prevent damage to the

fabrics, it is not possible to increase the speed over that

which is automatically suitable during the selection of the

program.

It is possible to modify the spin speed without to pausing the

machine.

NOTE:

THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC

DEVICE, WHICH PREVENTS THE SPIN CYCLE SHOULD

THE LOAD BE UNBALANCED. THIS REDUCES THE NOISE

AND VIBRATION IN THE MACHINE AND SO PROLONGS

THE LIFE OF YOUR MACHINE.

SPIN SPEED INDICATOR LIGHT

When you set a program,the maximum possible spin speed

will be automatically shown by the relevant indicator light.

Choosing a smaller spin speed by the appropriate button,

the relevant indicator light will go on.

The option buttons should be selected before pressing the

START button

SUPER RAPID BUTTON

By pushing this button the time of the wash programme is

reduced to a maximum of 50 minutes depending on the

programme and the temperature selected.The super rapid

button can be used for washing loads of 1 to 6 kg.

(This button can be utilised only on cottons and synthetic

programmes).

EXTRA RINSE BUTTON

The extra rinse program ensures clothing is thoroughly rinsed

and free of detergents. The program combines a unique

drum action with a number of additional rinses to achieve a

high degree of detergent free clothing.

The extra rinse program is ideal for people with sensitive skin

who require minimum detergent residue to avoid irritation or

allergies. It is advisable to use this program to clean

children’s clothing, towels and heavily soiled items where a

lot of detergent has been used and is retained in the fibres.

Note: - This program is not suitable for woollen garments and

is not available during the wool program.

CREASE GUARD BUTTON

The Crease Guard function minimizes creases as much as

possible with a uniquely designed anti-crease system that is

tailored to specific fabrics.

MIXED FABRICS - the water is gradually cooled throughout

the final two rinses with no spinning and then a delicate spin

assures the maximum relaxation of the fabrics.

DELICATE FABRICS – final two rinses with no spinning and then

the fabrics are left in water until it is time to unload. When you

are ready to unload, press the "Crease Guard" button – this

will drain.

WOLLENS/HAND WASH – after the final rinse the fabrics are

left in water until it is time to unload and the button indicator

blinking.

When you are ready to unload, press the "Crease Guard"

button, this will drain and spin ready for emptying.

If you do not want to spin the clothes and activate drain

only:

- Turn the programme selector to the "OFF" position;

- Select programme drain only ;

- Switch on the appliance again by pressing the

"Start/Pause" button.

START BUTTON

When a programme is selected, wait for the “STOP” indicator

light to flash before pressing the START button.

Press to start the selected cycle (according to the selected

cycle one indicator lights will go on) .

NOTE: WHEN THE START BUTTON HAS BEEN PRESSED THE

APPLIANCE CAN TAKE A FEW SECONDS BEFORE IT

STARTS WORKING.

CHANGING THE SETTINGS AFTER THE PROGRAMMES HAS

STARTED (PAUSE)

The programme may be paused at any time during the wash

cycle by holding down the "Start/Pause" button for about

two seconds.When the machine is in the paused mode, the

indicator light "Time countdown",Spin Speed and option

buttons will flash. To restart the programme, press the START

button once again.

If you wish to add or remove items during washing, wait 1

minute until the safety device unlocks the door.

When you have carried out the manoeuvre, close the door,

press START button and the appliance will continue working

from where it left off.

CANCELLING THE PROGRAMME

To cancel the programme,set the selector to the OFF position.

Select a different programme.

Re-set the programme selector to the OFF position.

BUTTON INDICATOR LIGHT

These light up when the relevant buttons are pressed.

If an option is selected that is not compatible with the

selected programme then the light on the button first flashes

and then goes off.

20 21

WEIGHT

MAX

1,5

TEMP.

°C

90°

60°

40°

30°

60°

50°

40°

30°

40°

60°

40°

II I

●●

●●●

●●

●●●

●●

●

●●

PROGRAMME

SELECTOR ON:

Please read these notes

When washing heavily soiled laundry it is recommended the load is reduced to 4 kg maximum.

Information for the test laboratories

(Ref. EN 50229 Standards)

Washing

Use the programme **

Drying

First drying with 4kg (the load consist: pillowcases and hand-towels) selecting the cotton

drying programme ( ) cupboard dry ( ).

Second drying with 2kg (the load consist: 2 sheets and hand towels) selecting the cotton

drying programme ( ) 90 minutes

(90’).

The spin speed may also be reduced, to match any guidelines suggested on the fabric label, or for

very delicate fabrics cancel the spin completely this option is available with a spin speed button.

* Programmes for automatic drying.

TABLE OF PROGRAMMES

Resistant fabrics

Cotton, linen

Cotton, mixed

resistant

Cotton, mixed

Mixed fabrics and synthetics

Mixed, resistant

Cotton, mixed fabrics,

synthetics

Synthetics (nylon,

perlon), mixed cotton

Very delicate fabrics

CHARGE DETERGENT

PROGRAM FOR:

SpecialS

Whites

Whites with

Prewash

Fast coloureds

Non fast coloureds

Delicates

Fast coloureds with

Prewash

Fast coloureds

Synthetics

Non fast coloureds

Rinse

Fast spin

Drain only

Delicates

“MACHINE

WASHABLE”

woollens

Hand wash

Rapid 30 minute

Resistant Fabrics

“All 40°C”

system programme

Cotton - Drying

Mixed - Drying

CHAPTER 7

30 MINUTE RAPID PROGRAMME

The 30 minute rapid programme allows a complete washing

cycle to be carried out in approximately 30 minutes, with up

to a maximum load of 2 kg and a temperature of 40°C.

When selecting the "30 minute rapid" programme, please

note that we recommend you use only 20% of the

recommended quantities shown on the detergent pack.

“A” WASH 59 '

This specially designed programme maintains the high quality

wash performance identified with the “A” rating whilst greatly

reducing the wash time. The programme is designed for a

maximum load of 3 kg with a temperature of 60°C and

concludes with 2 rinses and a high speed spin sequence.

AA SPECIAL PROGRAMME at 40°C

This special programme has been studied to allow you to

obtain the best washing performance, even at full load, as

the 60°C Cotton programme (the normative cycle),but with

the advantage of an energy saving due to 40°C

temperature,instead of 60°C.

The length of this programme lasts almost the 3 hours.

“ALL 40°C” PROGRAMME

This is an exclusive system and involves 2 great advantages

for the consumer:

• to be able to wash together different type of fabrics (e.g.

cotton + synthetic etc…) FAST COLOUREDS;

•to wash with a considerable energy saving.

The “All 40°C” is an eco friendly programme that has low

energy consumption (850W/h). The programme achieves this

by using a low water temperature combined with periods of

inactive soaking and short periods of drum cycling over a

period of three hours.

Important:

•the first washing of new coloureds fabrics must be done

separately;

• in every case, never mix NON-FAST COLOUREDS fabrics.

Drying

Note: Dispensers used for concentrated powders and liquid

detergents must be removed from the drum before

commencing the tumble drying programmes.

The drum changes direction during the drying cycle to

prevent the laundry from tangling and hence produce even

drying. Cool air is used during the last ten minutes of the

drying cycle to minimise creasing.

High Heat

High temperature drying programme for Cottons and linen

items, always refer to the care label

Low Heat

Low temperature drying programme for synthetics and mixed

fibres, always refer to the care label.

CHAPTER 8

SELECTION

For the various types of fabrics and various degrees of dirt the

washing machine has different programme bands according to:

wash cycle, temperature and lenght of cycle (see table of

washing cycle programmes).

RESISTANTS FABRICS

The Cotton programme is designed for maximum washing and

rinsing efficiency.With spin cycles in between, the programme

guarantees the laundry is rinsed perfectly.The final spin cycle

ensures laundry is spun dry as much as possible up to the

maximum speed.

The Cotton programme includes a Prewash cycle.This option is

particularly useful for really dirty loads and can be used

independently of the main wash programme.Additional

detergent for the Prewash part of the programme should be

added to the first compartment of the soap drawer labelled "I"

(please refer to the section of this manual entitled “Detergent”).

We recommend you use only 20% of the quantity used for the

main wash programme.

MIXED AND SYNTHETIC FABRICS

The main wash and the rinse gives best results thanks to the

rotation rhythms of the drum and to the water levels.

A gentle spin will mean that the fabrics become less creased.

SPECIAL “RINSE” PROGRAMME

This programme carries out three rinses with a intermediate spin

(which can be reduced or excluded by using the correct button). It

can be used for rinsing any type of fabric,eg.use after hand-washing.

SPECIAL “SPIN” PROGRAMME

Programme “SPIN” carries out a maximum spin (which can be

reduced by using the correct button).

DRAIN ONLY

This programme drains out the water.

SPECIAL DELICATE FIBRES

This is a new wash cycle which alternates washing and soaking

and is particularly recommended for very delicate fabrics such as

Pure Machine Washable Wool. The wash cycle and rinses are

carried out with high water levels to ensure best results.

WOOLMARK PROGRAMME

The special cycle, certified by WOOLMARK, enables to

thoroughly wash garments without damaging them.The cycle

comprises of alternate periods of activity and pauses.The

programme has a maximum temperature of 30° and

concludes with 3 rinses and a short spin.

SPECIAL “HAND WASH”

This washing machine also has a gentle Hand Wash

programme cycle.This programme allows a complete

washing cycle for garments specified as “Hand Wash only” on

the fabric care label. The programme has a temperature of

30°C and concludes with 3 rinses and a slow spin.

CHAPTER 10

THE PRODUCT

IMPORTANT:

When washing heavy rugs, bed spreads and other heavy

articles, it is advisable not to spin.

Do not dry wool,items with special padding delicate silk

irems; rubber, plastic, including some types of plastic

poppers on duvet covers and foam plastic items are not

suitable for tumble drying.

To be machine-washed,woollen garments and other articles

in wool must bear the “Machine Washable Label”.

IMPORTANT:

When sorting articles ensure that:

- there are no metal objects in the washing (e.g.

brooches, safety pins, pins, coins etc.).

- cushion covers are buttoned, zips and hooks are

closed, loose belts and long tapes on dressing gowns

are knotted.

- runners from curtains are removed.

- attention is paid to garment labels.

- when sorting, any tough stains should be removed prior

to washing using stain removers only recommended on

label.

CHAPTER 9

DETERGENT DRAWER

The detergent draw is split into 3 compartments:

- the compartment labelled "I" is for prewash detergent;

- the compartment labelled “✿✿” is for special additives,

fabric softeners, fragrances, starch, brighteners etc;

- the compartment labelled "II" is for main wash detergent.

If liquid detergents are used, please insert the special

container supplied into the compartment marked “II” in the

detergent drawer.This ensures that the liquid detergent

enters the drum at the right stage of the wash cycle.

This special container must be inserted when using the

“RINSE” program as a BLEACHING cycle.

NOTE: SOME DETERGENTS ARE DIFFICULT TO REMOVE.

FOR THESE, WE RECOMMEND YOU USE THE SPECIAL

DISPENSER WHICH IS PLACED IN THE DRUM.

NOTE: ONLY PUT LIQUID PRODUCTS IN THE

COMPARTMENT LABELLED “

✿✿”. THE MACHINE IS

PROGRAMMED TO AUTOMATICALLY TAKE UP

ADDITIVES DURING THE FINAL RINSE STAGE FOR ALL

WASH CYCLES.

WASHING

VARIABLE CAPACITY

This washing machine automatically adapts the level of the water

to the type and quantity of washing.In this way it is also possible to

obtain a “personalized” wash from an energy saving point of view.

This system gives a decrease in energy consumption and a

sensible reduction in washing times.

EXAMPLE:

A net bag should be used for particularly delicate fabrics.

Let us suppose that the washing consists of HEAVILY SOILED

COTTON (tough stains should be removed with suitable stain

removal).

It is advisable not to wash a load made up entirely of articles

in towelling fabric which absorb a lot of water and become

too heavy.

● Open the detergent drawer .

● Put 120 g in the main wash compartment marked II.

● Put 50 ml of the desired additive in the additives

compartment

✿✿

● Close the detergent drawer .

CHAPTER 11

CUSTOMER AWARENESS

A guide environmentally friendly and economic use of your

appliance.

MAXIMISE THE LOAD SIZE

Achieve the best use of energy, water, detergent and time by

using the recommended maximum load size.

Save up to 50% energy by washing a full load instead of 2 half

loads.

DO YOU NEED TO PRE-WASH?

For heavily soiled laundry only!

SAVE detergent, time, water and between 5 to 15% energy

consumption by NOT selecting Prewash for slight to normally

soiled laundry.

IS A HOT WASH REQUIRED?

Pretreat stains with stain remover or soak dried in stains in water

before washing to reduce the necessity of a hot wash

programme.

Save up to 50% energy by using a 60°C wash programme.

BEFORE USING A DRYING PROGRAMME...

SAVE energy and time by selecting a high spin speed to

reduce the water content in laundry before using a drying

programme.

CHAPTER 12

DRYING

DON’T DRY GARMENTS MADE FROM FOAM RUBBER

OR FLAMMABLE MATERIALS.

IMPORTANT:

THIS DRYER CAN ONLY BE USED FOR LAUNDRY

WHICH HAS BEEN WASHED AND SPIN DRIED.

WARNING:

Indications given are general, therefore some practice is

needed for the best drying results. We recommend setting a

lower drying time than indicated, when first using, so as to

establish the degree of dryness required. We recommend

not to dry fabrics that fray easily, such as rugs or garments

with a deep pile, to avoid air duct clogging.

The water is then conveyed to the drain circuit,which is

sealed and therefore, no steam can be released outside.

● Ensure that the water inlet tap is turned on.

● And that the discharge tube is in place.

PROGRAMME SELECTION

Refer to the programme guide to select the most suitable

programme.

Turning the selector knob required programme is activate.

Wait for the “STOP”indicator light to flash.

Then press the START button.

When the START button is pressed the machine sets the

working sequence in motion.

The programme carries out with the programme selector

stationary on the selected programme till cycle ends.

Warning: If there is any break in the power supply while the

machine is operating, a special memory stores the selected

programme and,when the power is restored, it continues

where it left off.

● At the end of the programme the indicator light “end

cycle” will go on.

● When the programme has finished

Wait for the door lock to be released (about 1 minute after

the programme has finished).

Switch off the machine by turning the programme selector

to the “OFF” position.

Open the door and remove the laundry.

Turn OFF the water supply after every use.

FOR ALL TYPES OF WASH CONSULT THE PROGRAMME

TABLE AND FOLLOW THE OPERATIONS IN THE ORDER

INDICATED.

4 kg MAX

The correct way to dry:

● Open door.

● Fill with up to 4 kg - in case of large items (e.g. sheets) or

very absorbent items (e.g. towels or jeans),it is a good idea

to reduce the load.

● Close door.

● Turn programme dial to cotton .

● Select the degree of dryness that you require.

This ranges from Extra Dry ( ) for bath towels and

bathrobes, through Cupboard Dry ( ) for items that will be

put away without ironing, to iron dry ( ) that leaves the

laundry suitable

for ironing.

If you wish to select a timed drying cycle, press the “drying

programme selection” button until the required time

indicator lights up.

DOUBLE-SKIN DOOR

The appliance door is fitted with a protective shield to

prevent contact being made with the glass which reaches

high temperatures, particularly during the drying cycle.

WARNING: DO NOT TOUCH DOOR FOR ANY REASON

WHATSOEVER.

● Make sure water tap is open.

● Make sure water drain is correctly positioned.

IMPORTANT

NEVER OPEN THE DOOR AFTER THE DRYING CYCLE

HAS BEGUN - WAIT UNTIL THE COOL DOWN PERIOD

PROVIDED FOR BY THE CYCLE.

Only dry pre-spun laundry

The washer/dryer can perform two types of drying:

Cotton, terry towelling,linen, hemp fabrics, etc...

Advisory note

During drying phase the drum will accelerate to a higher

speed to distribute the load and to optimize the drying

performance

Mixed fabrics (synthetics/cotton), synthetic fabrics.

PROGRAMME

Extra

Wardrobe

Iron

Min 1 Kg

from 30’

Min 1 Kg

from 30’

Max 3 Kg

to 170’

to 150’

to 80’

COTTON MIXED

TABLE OF DRYING TIMES (IN MINUTES):

Max 4 Kg

to 230’

to 220’

to 170’

WARNING:

DO NOT DRY WOOLLEN GARMENTS OR ARTICLES WITH

SPECIAL PADDING, (E.G. QUILTS, QUILTED ANORAKS,

ETC.).

DELICATE FABRICS IF GARMENTS ARE DRIP/DRY, LOAD

LESS ITEMS AO AS TO PREVENT CREASING.

● Press the START button.

● The drying phase will begin with the programme dial fixed

on the symbol until the end of drying.

● The drying programme indicator will be on until the cool

down phase will begin and the indicator ( ) will go on.

● At the end of the programme the indicator light “Stop” will

go on.

● Wait for the door lock to be released (about 1 minute after

the programme has finished).

The "Door Security" indicator light will go out.

● Switch off the machine by turning the programme selector

on the “OFF” position.

● Open the door and remove the laundry.

● Turn off the water supply after every use.

USEFUL TIPS:

Do not dry unwashed items in the washer dryer.

Items that have been soiled with substances such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine, waxes and wax removers should be

washed in hot water with an extra amount of detergent before being dried in the

washer dryer.

Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted with foam rubber pads should not be

dried in the washer dryer.

Fabric softeners, or similar products, should be used as specified by the fabric softener

instructions.

The final part of a washer dryer cycle occurs without heat (cool down cycle) to

ensure that the items are left at a temperature that ensures that the items will not be

damaged.

WARNING:

Never stop a washer dryer before the end of the drying cycle unless all items are

quickly removed and spread out so that the heat is dissipated.

The programme carries out with the programme selector

stationary on the selected programme till cycle ends.

The washer-dryer will then complete the entire drying

programme.

The drying programme indicator will be on until the cool

down phase will begin and the indicator ( ) will go on.

At the end of the programme the indicator light “Stop” will

go on.

Wait for the door lock to be released (about 1 minute after

the programme has finished).

The "Door Security" indicator light will go out.

Switch off the machine by turning the programme selector

on the “OFF” position.

Open the door and remove the laundry.

Turn off the water supply after every use.

CHAPTER 13

AUTOMATIC WASHING/DRYING

WARNING: ONLY A MAXIMUM 4 KG OF DRY LAUNDRY

CAN BE LOADED OTHERWISE THE DRIED LAUNDRY WILL

BE NOT SATISFACTORY.

Washing:

Open the drawer, choose the detergent and put in the

correct amount.

Refer to the list of washing programmes according to fabrics

to be washed (e.g.very dirty cotton) and without pressing

Start button, prepare wash as described:

Turning the selector knob, the required programme is

activated.

Press the option buttons (if required)

Check that the tap is turned on and that the discharge hose

is positioned correctly.

Drying:

Select the degree of dryness that you require.

This ranges from Extra Dry ( ) for bath towels and

bathrobes, through Cupboard Dry ( ) for

items that will be put away without ironing, to iron dry ( )

that leaves the laundry suitable for ironing.

If you wish to select a timed drying cycle, press the “drying

programme selection” button until the required time indicator

lights up.

Press the "Start/Pause" button.

4 kg MAX

CHAPTER 14

CLEANING AND ROUTINE MAINTENANCE

Do not use abrasives, spirits and/or diluents on the exterior of

the appliance. It is sufficient to use a damp cloth.

The washing machine requires very little maintenance:

● Cleaning of drawer compartments.

● Removals or long periods when the machine is left

standing.

CLEANING OF DRAWER COMPARTMENTS

Although not strictly necessary, it is advisable to clean the

detergent, bleach and additives compartments occasionally.

Remove the compartments by pulling gently.

Clean with water.

Put the compartments back into place

REMOVALS OR LONG PERIODS WHEN THE MACHINE IS LEFT

STANDING

When the machine is left standing for long periods in

unheated rooms, the drain hose should be emptied of all

remaining water.

This operation is recommended when moving the appliance

from its installation.

The appliance must be switched off and unplugged. A bowl

is needed. Detach the drainage hose from the clamp and

lower it over the bowl until all the water is removed.

Repeat the same operation with the water inlet hose.

Advisory note

During drying phase the drum will accelerate to a higher speed to distribute the load and to

optimize the drying performance

CHAPTER 15

FAULT

If the fault should persist, contact a Technical Assistance Centre.For prompt servicing, give the model of the

washing machine, to be found on the label placed on the cabinet inside of the porthole.

Important

1 The use of environment friendly detergents without phosphates may produce the following effects:

- The discharge rinse water may result cloudier due to the presence of zeolites in suspension. This does not

compromise the efficiency of the rinses.

- The presence of white powder (zeolites) on the washing at the end of the washing cycle. This does not

remain incorporated in the fabric and does not alter the colour.

- The presence of foam in the last rinse water which is not necessarily a sign of inadequate rinsing.

- The non-ionic surface-active agents present in the composition of washing machine detergents are often

difficult to remove from the washing itself and, even in small quantities, may produce visible signs of the

formation of foam.

- Carrying out further rinses, in cases such as this, is not useful.

2 If your washing machine fails to function, carry out the above-mentioned checks before calling the Technical

Assistance Service.

1. Does not function

on any

programme

2. Does not load

water

3. Does not discharge

water

4.Water on floor

around washing

machine

5. Does not spin

6. Strong vibrations

during spin

Mains plug not plugged in

Mains switch not on

No power

Electric circuit fuses failure

Load door open

See cause 1

Inlet tap turned off

Discharge tube bent

Leak from the washer between the tap

and inlet tube

The washing machine has not

discharged water

“No spin” setting (some models only)

Washing machine not perfectly level

Transport bracket not removed

Washing load not evenly distributed

Insert plug

Turn on mains switch

Check

Close load door

Check

Turn on water inlet tap

Straighten discharge tube

Replace washer and tighten the tube

on the tap

Wait a few minutes until the machine

discharges water

Turn the programme dial onto spin

setting

Adjust special feet

Remove transport bracket

Distribute the washing evenly

CAUSE

REMEDY

Our Customer Care Centre can be called on:

0871 22 22 503

We aim to answer calls as quickly as possible, and in strict rotation as soon as one of our

Customer Care team become free.

Our Customer Care Centre opening hours are:

Monday - Friday 8.00am - 8.00pm

Saturday 8.30am - 6.00pm

Sunday 10.00am - 4.00pm

Please ensure that you have available your appliances model number and serial number,

there is a space at the back of this book for recording that information.

Alternatively visit the web site as detailed on the front cover of the handbook.

Outside the UK and Northern Ireland, please contact your local supplier.

In case of difficulty within the UK and Northern Ireland, please call Belling Customer Care

Centre Helpline on

0871 22 22 503

Our Customer Care Centre is open during the hours below:

Monday to Friday 8am - 8pm

Saturday 8.30am - 6pm

Sunday 10am - 4pm

Please have to hand your appliances Model Number and Serial Number, which can be found

on the databadge inside you cooker and recorded here for future reference.

Glen Dimplex Home Appliances Limited is the owner of the Belling brand and is part of

the Glen Dimplex group of companies.

Stoney Lane, Prescot,Merseyside, L35 2XW

Model Number

Serial Number

NOTE:

THE MACHINE IS FITTED WITH A SPECIAL ELECTRONIC DEVICE, WHICH PREVENTS THE SPIN CYCLE

SHOULD THE LOAD BE UNBALANCED.

THIS REDUCES THE NOISE AND VIBRATION IN THE MACHINE AND SO PROLONGS THE LIFE OF YOUR

MACHINE.

Page is loading ...

Terzismo BEL WD 14v User manual

Brand: Terzismo

Model: BEL WD 14v

Category: Washing machines

Type: User manual

Download PDF

report

Terzismo BEL WD 14v User manual

Terzismo BEL WD 14v User manual

Related papers

Other documents