LG OLED65GXPTA User manual

Brand: LG

Model: OLED65GXPTA

Type: User manual

This manual is also suitable for

www.lg.com

Please read this manual carefully before operating

your set and retain it for future reference.

OWNER’S MANUAL

Safety and Reference

*MFL71689212*

(2011-REV02)

ENGLISH

India region only. (Below sentence is not applicable for above 1920 x 1080 resolution TV models.)

ATTENTION:

This product is qualied for the BEE Star rating in the ‘Home’ Mode.

The Objectives of Star Labeling Program is designed to promote energy ecient products and practices.

When the television is initially set up, it is designed to meet the BEE Star Labeling requirements while maintaining optimum picture quality.

• Changes to certain functionalities of this television (TV Guide, Picture/sound etc) may change the power consumption.

• Depending upon such changed setting (eg., Retail mode), the power consumption may vary which possibly could exceed the stated energy

consumption.

To reset the television to Star rating qualied settings, select ‘Home’ mode from the initial set-up procedure in ‘factory settings’ under the ‘Set-up’

menu.

ENGLISH

Warning! Safety

Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s

enclosure that may be of sucient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK,

DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS

WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

• Do not place the TV and/or remote control in the following

environments:

- Keep the product away from direct sunlight.

- An area with high humidity such as a bathroom.

- Near any heat source such as stoves and other devices that

produce heat.

- Near kitchen counters or humidiers where they can easily be

exposed to steam or oil.

- An area exposed to rain or wind.

- Do not expose to dripping or splashing and do not place objects

lled with liquids, such as vases, cups, etc. on or over the

apparatus (e.g., on shelves above the unit).

- Near ammable objects such as gasoline or candles, or expose

the TV to direct air conditioning.

- Do not install in excessively dusty places.

Otherwise, this may result in re, electric shock, combustion/

explosion, malfunction or product deformation.

• Ventilation

- Install your TV where there is proper ventilation. Do not install in

a conned space such as a bookcase.

- Do not install the product on a carpet or cushion.

- Do not block or cover the product with cloth or other materials

while unit is plugged in.

• Take care not to touch the ventilation openings. When watching

the TV for a long period, the ventilation openings may become hot.

• Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon.

Pay particular attention to plugs, wall outlets, and the point where

the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely tting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not

pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as

this could result in re or electric shock.

• Disconnecting the Device from the Main Power

- The power plug is the disconnecting device. In case of an

emergency, the power plug must remain readily accessible.

• Do not let your children climb or cling onto the TV. Otherwise, the

TV may fall over, which may cause serious injury.

• Outdoor Antenna Grounding (Can dier by country):

- If an outdoor antenna is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity

of overhead power lines or other electric light or power circuits,

or where it can come in contact with such power lines or circuits

as death or serious injury can occur.

ENGLISH

• Grounding (Except for devices which are not grounded.)

- TV with a three-prong grounded AC plug must be connected to

a three-prong grounded AC outlet. Ensure that you connect the

earth ground wire to prevent possible electric shock.

• Never touch this apparatus or antenna during a lightning storm.

You may be electrocuted.

• Make sure the power cord is connected securely to the TV and wall

socket if not secured damage to the Plug and socket may occur and

in extreme cases a re may break out.

• Do not insert metallic or inammable objects into the product. If a

foreign object is dropped into the product, unplug the power cord

and contact the customer service.

• Do not touch the end of the power cord while it is plugged in. You

may be electrocuted.

• If any of the following occur, unplug the product

immediately and contact your local customer service.

- The product has been damaged.

- If water or another substance enters the product (like an AC

adapter, power cord, or TV).

- If you smell smoke or other odors coming from the TV

- When lightning storms or when unused for long periods of time.

Even the TV is turned o by remote control or button, AC power

source is connected to the unit if not unplugged in.

• Do not use high voltage electrical equipment near the TV (e.g., a

bug zapper). This may result in product malfunction.

• Do not attempt to modify this product in any way without written

authorization from LG Electronics. Accidental re or electric shock

can occur. Contact your local customer service for service or repair.

Unauthorized modication could void the user’s authority to

operate this product.

• Use only an authorized attachments / accessories approved by

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction, or product damage.

• Never disassemble the AC adapter or power cord. This may result in

re or electric shock.

• Handle the adapter carefully to avoid dropping or striking it. An

impact could damage the adapter.

• To reduce the risk of re or electrical shock, do not touch the TV

with wet hands. If the power cord prongs are wet or covered with

dust, dry the power plug completely or wipe dust o.

• Batteries

- Store the accessories (battery, etc.) in a safe location out of the

reach of children.

- Do not short circuit, disassemble, or allow the batteries to

overheat. Do not dispose of batteries in a re. Batteries should

not be exposed to excessive heat.

- Caution : Risk of re or explosion if the battery is replaced by an

incorrect type.

• Moving

- When moving, make sure the product is turned o, unplugged,

and all cables have been removed. It may take 2 or more people

to carry larger TVs. Do not press or put stress on the front panel

of the TV. Otherwise, this may result in product damage, re

hazard or injury.

• Keep the packing anti-moisture material or vinyl packing out of the

reach of children.

• Do not allow an impact shock, any objects to fall into the product,

and do not drop anything onto the screen.

• Do not press strongly upon the panel with a hand or a sharp

object such as a nail, pencil, or pen, or make a scratch on it. It may

causedamage to screen.

• Cleaning

- When cleaning, unplug the power cord and wipe gently with a

soft/dry cloth. Do not spray water or other liquids directly on the

TV. Do not clean your TV with chemicals including glass cleaner,

any type of air freshener, insecticide, lubricants, wax (car,

industrial), abrasive, thinner, benzene, alcohol etc., which can

damage the product and/or its panel. Otherwise, this may result

in electric shock or product damage.

ENGLISH

Preparing

• If the TV is turned on for the rst time after it was shipped from the

factory, initialization of the TV may take a few minutes.

• Image shown may dier from your TV.

• Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

• The available menus and options may dier from the input source

or product model that you are using.

• New features may be added to this TV in the future.

• The device must be easily accessed to a location outlet near the

access. Some devices are not made by turning on / o button,

turning o the device and unplugging the power cord.

• The items supplied with your product may vary depending on the

model.

• Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and USB devices should

have bezels less than 8 mm thick, 18 mm width and 8 mm a wire

diameter. Use an extension cable that supports or higher

if the USB cable or USB memory stick does not t into your TV’s

USB port.

* A ≦ 8 mm

* B ≦ 18 mm

* C ≦ 8 mm

• Use a certied cable with the HDMI logo attached.

• If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur.

• Recommended HDMI Cable Types

- Ultra High Speed HDMI

/™ cable (3 m or less)

Separate Purchase

Separate purchase items can be changed or modied for quality

improvement without any notication. Contact your dealer to buy these

items. These devices only work with certain models.

The model name or design may be changed depending on the upgrade

of product functions, manufacturer’s circumstances or policies.

Magic Remote Control

MR20GA

Check whether your TV model supports Bluetooth in the Wireless

Module Specication to verify whether it can be used with the Magic

Remote.

Stand

(Depending on model)

Stand Model

AN-GXDV55 OLED55GX*

AN-GXDV65 OLED65GX*

AN-GXDV77 OLED77GX*

ENGLISH

Wall Mounting Bracket

(Depending on model)

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Model OLED55/65/77GX*

VESA (A x B) (mm) 300 x 300

Standard screw M6

Number of screws 4

Wall mount bracket OLW480B

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material

that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all

cables.

• When holding the TV, the screen should face away from you to

avoid damage.

• Hold the side and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV to jolts or excessive

vibration.

• When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause exing / bending of frame

chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding

buttons.

• Avoid touching the screen at all times, as this may result

in damage to the screen.

• When attaching the stand to the TV set, place the screen

facing down on a cushioned table or at surface to

protect the screen from scratches.

ENGLISH

Mounting on the Table

1 Lift and tilt the TV into its upright position on a table.

• Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

(Depending on model)

2 Connect the power cord to a wall outlet.

• Do not apply foreign substances (oils, lubricants, etc.) to

the screw parts when assembling the product. (Doing so

may damage the product.)

• If you install the TV on a stand, you need to take actions

to prevent the product from overturning. Otherwise, the

product may fall over, which may cause injury.

• Do not use any unapproved items to ensure the safety

and product life span.

• Any damage or injuries caused by using unapproved

items are not covered by the manufacturer’s warranty.

• Make sure that the screws are inserted correctly and

fastened securely. (If they are not fastened securely

enough, the TV may tilt forward after being installed.)

Do not use too much force and over tighten the screws;

otherwise screw may be damaged and not tighten

correctly.

• When installing on a cabinet or a shelf using a stand,

make sure its width is greater than that of the TV.

• If a television is not positioned in a suciently stable

location, it can be potentially hazardous due to falling.

Many injuries, particularly to children, can be avoided

by taking simple precautions such as:

- Using cabinets or stands recommended by the

manufacturer of the television.

- Only using furniture that can safely support the

television.

- Ensuring the television is not overhanging the edge

of the supporting furniture.

- Not placing the television on tall furniture (for

example, cupboards or bookcases) without

anchoring both the furniture and the television to a

suitable support.

- Not standing the televisions on cloth or other

materials placed between the television and

supporting furniture.

- Educating children about the dangers of climbing on

furniture to reach the television or its controls.

Securing TV to the Wall

(Depending on model)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

• If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall. Match the

location of the wall bracket and the eye-bolts on the rear of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

• Use a platform or cabinet that is strong and large enough to

support the TV securely.

• Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

ENGLISH

Mounting to the Wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the use

of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with

cables connected. When you do not use LG’s wall mount bracket, please

use a wall mount bracket where the device is adequately secured to the

wall with enough space to allow connectivity to external devices. It is

advised to connect all the cables before installing xed wall mounts.

10 cm

(Depending on model)

• Remove the stand before installing the TV on a wall

mount by performing the stand attachment in reverse.

• For more information of screws and wall mount bracket,

refer to the Separate purchase.

• If you intend to mount the product to a wall, attach VESA

standard mounting interface (optional parts) to the back

of the product. When you install the set to use the wall

mounting bracket (optional parts), x it carefully so as

not to drop.

• When mounting a TV on the wall, make sure not to install

the TV by hanging the power and signal cables on the

back of the TV.

• Do not install this product on a wall if it could be exposed

to oil or oil mist. This may damage the product and cause

it to fall.

• When installing the Full Contact Wall Mount, the TV may

not be contacted rmly against the wall due to some wall

conditions.

For more information, watch the installation

video on your smart device.

Precautions for Safety

(Except for OLW480B)

• Professional installers should read this manual carefully to ensure

proper installation.

• Professional installers should forward this manual to customers

after installation and encourage them to read and store it in a

convenient place for future reference.

After reading the installation manual, keep it in a convenient place

for future reference.

• Ask a professional installer appointed by the store for

installation of the product.

Installation by someone other than a professional installer

is extremely dangerous and may result in personal injury.

• Do not install the product in an unstable site that cannot

withstand its weight.

If the installation site lacks sucient rigidity, the product

may fall and cause personal injury.

• Contact a professional installer appointed by the store prior

to moving or replacing the product after installation.

Installation is a technical task and safety issues may arise

if an individual attempts to install or move the product

personally.

• Do not hang on the product or subject it to severe impact

after installation.

Doing so may cause the product to fall and cause personal

injury.

• When installing the product on a wall, do not hang the

power line or signal cables from the back of the TV.

This can damage the cords, resulting in a re, electrical

shock or malfunction of the product.

• Be sure to wear work gloves when installing the product.

- Installing with unprotected hands may result in injury.

ENGLISH

• Install the product according to the instructions in the

installation manual.

Failure to install the product according to the instructions

in the installation manual can result in serious personal

injury or product damage.

• Be sure to have at least two people when installing the

product or adjusting the product’s height.

Attempting to perform installation or adjustments

personally may result in personal injury or damage to the

product.

• Make sure a wall is available prior to proceeding with

installation. Make use of the anchors and screws provided

with the product.

Use of any unauthorized anchors or screws may not

support the product's weight, which poses safety risks.

• When drilling in the wall for installation, be sure to use

drill bits and drills of the specied diameter. Follow the

instructions for the hole depth.

Drilling and installing the product in ways other than

specied in the installation manual may result in an

unstable installation and potential safety issues.

• Do not wipe the product with a wet towel or use any

heating equipment or humidier under the place where

the product is installed.

Liquid water or vapor may enter the product and excessive

heat may cause re, electric shock, or malfunction.

• Do not install the product near a re sprinkler or detector,

a place where vibration or shock may occur or near a high-

voltage wire or power source.

• Unplug the product’s power cord from the wall outlet

before installing.

Installing the product while the power cord is plugged in

may result in electric shock or re.

• Do not install the product with bare hands. Be sure to wear

work gloves.

Attempting installation without work gloves may cause

personal injury.

• Connect the product with the supplied cable. Use of an

unauthorized cable may result in damage by friction with

the wall. Make sure to use the supplied cable gender. (This

may vary by model.)

Before Installation

(Except for OLW480B)

• Do not use the product for any purpose other than installing the

TV on a wall.

• Avoid product damage and safety accidents caused by careless

installing or use of improper or unauthorized wall mount.

• Follow the instructions in the installation manual for a convenient

installation of the wall mount.

• Immediately discontinue installation and contact the service center

if you cannot fully understand the installation process.

Use a professional installer if any installation issues remain after

the inquiry.

• Installation of this product on a concrete wall or wood stud is

recommended. Installation of this product on other surfaces

(Dry wall, plywood, bricks, etc.) is not recommended. Improper

installation may result in the product falling.

• Install the product only on a vertical wall.

Do not install on a tilted wall that exceeds building standards or on

the heavily titled wall or ceiling.

LG is not responsible for problems caused by improper installation

of the product, e.g., heavily tilted walls and ceilings.

• Check the enclosed accessories before installation. We are not

responsible for any lost or damaged accessories after the inner

packaging is opened.

• When an infant or small child swallows the enclosed accessories,

various safety accidents such as choking may occur. Keep the

enclosed accessories out of the reach of infants and children.

• When tightening screws, tighten until fully snug.

Avoid using excessive force when tightening the screws. Doing

so may damage the wall and product or reduce the rigidity or

performance of the product.

• Avoid installing a TV that exceeds the specied tensile load, and do

not allow any external force to be applied to the product.

• Avoid accidents by using work tools with care during installation.

Tools for Installation

• “+” shaped screwdriver (manual or electric) / level / drill / Ø 8 mm

drill bit for concrete or Ø 4 mm drill bit for steel

ENGLISH

Securing TV to the Wall

(Except for OLW480B)

• Please use the TV close to the wall after installation.

How to x anchors and screws

(Except for OLW480B)

Please make sure that:

• Check that the material and thickness of the wall and nishing

material comply with the installation manual. Before beginning

the mounting process, you must be sure the wall is able to support

the weight of the TV.

• Should use the enclosed anchors and screws on crack-free concrete

walls.

• Never install the product on a plasterboard or wall made of paper

or medium-density berboard (MDF). When it is necessary to

install the product on such wall, anchor screws must be fastened

to retaining walls (concrete) or wood Stud inside the nishing

material.

• The wall mount should be attached to a stud.This usually will not

be a problem, but depending on individual circumstances, there

may be cases when the ability to mount into a studis not possible.

In this case, there are a variety of drywall anchors, such as toggle

bolts, which may provide a solution.If using drywall anchors,

please be sure the anchors and the wall have the ability to support

the weight of your TV. Please note that the supplied anchors may

not be the correct ones for your individual situation, so you should

check with a local professional.

• Other unspecied walls must be capable of supporting pullout

loads of over 70kgf (686N) and shear loads of over 100kgf (980N)

per fastener.

• Use an Ø 8mm drill bit for concrete and a hammer (impact) drill or

Ø 4mm drill bit for wood stud to drill holes.

(For installation on concrete wall)

1 Drill holes in anchor locations with a drill bit of Ø 8 mm to a

depth of 80 mm to 100 mm.

2 Clean the drilled holes.

3 Insert the enclosed anchors for xing the wall mount into the

holes. (Use a hammer when inserting anchors.)

Wall mounting anchor

4 Push the wall mount support closely toward the wall to match

the hole locations.

5 Tighten screws for xing the wall mount to the holes. At this

time, tighten the screws to a torque of between 45 kgf/cm to

60 kgf/cm.

Wall mounting screw

ENGLISH

(For installation on wood stud)

Use the Ø 4 mm drill bit for wood to drill holes with the depth of

76mm. (Clean the drilled hole.)

Drywall

Wood stud

76 mm

Without using the wall mounting anchor, fasten the wall mounting

screw directly to the wood stud.

After Installation

• When connecting additional cables from the sides, we

recommend holding the centre of the TV horizontally or

vertically and pulling the product to make sure there is

sucient distance from the wall before connecting.

• When connecting additional cables from the bottom, we

recommend releasing the TV from the wall mount before

connecting.

• Use cable management systems to arrange the

cables at the bottom of the TV as shown below. Cable

managements are not provided with the product, so

purchase them separately.

(For example)

• After installing the product, be sure to use it adhered to

the wall.

- Using the product while it is not adhered to the wall

may damage or shake the product.

Connections

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Antenna/Cable

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplier properly to

improve the image quality.

• If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

• For a location that is not supported with ULTRA HD broadcasting,

this TV cannot receive ULTRA HD broadcasts directly.

Satellite dish

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω). (Depending on model)

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

HDMI

• When connecting the HDMI cable, the product and external devices

should be turned o and unplugged.

• Supported HDMI Audio format (Depending on model):

True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz),

PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

ENGLISH

• [Picture] [Additional Settings] [HDMI Ultra

HD Deep Colour]

- On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0), 4K @ 100/120Hz

(4:4:4, 4:2:2, 4:2:0)

- O: Support 4K @ 50/60 Hz (4:2:0)

If the device connected to Input Port also supports Ultra HD Deep

Colour, your picture may be clearer. However, if the device doesn’t

support it, it may not work properly. In that case, change the TV’s

[HDMI Ultra HD Deep Colour] setting to o.

USB

Some USB Hubs may not work. If a USB device connected using a USB

Hub is not detected, connect it to the USB port on the TV directly.

IR Blaster

• Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD

player, soundbar, game consoles, etc., using the IR Blaster.

(Depending on country)

- Connect the IR Blaster cable to the TV’s IR Blaster port.

- Place both ends (one or two) of the IR Blaster in front of the

external device as shown in the picture below.

- Use universal control settings to control the device. Go to

→ → [Connection] → [Device Connection Settings] →

[Universal Control Settings].

- Secure the IR Blaster with the 3M tape provided.

External Devices

Available external devices are: Blu-ray player, HD receivers, DVD players,

VCRs, audio systems, USB storage devices, PC, gaming devices, and

other external devices.

• The external device connection may dier from the model.

• Connect external devices to the TV regardless of the order of the

TV port.

• If you record a TV program on a Blu-ray/DVD recorder or VCR, make

sure to connect the TV signal input cable to the TV through a DVD

recorder or VCR. For more information of recording, refer to the

manual provided with the connected device.

• Refer to the external equipment’s manual for operating

instructions.

• If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

• In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the [Picture]

menu until the picture is clear.

• In PC mode, some resolution settings may not work properly

depending on the graphics card.

• If ULTRA HD content is played on your PC, video or audio may

become disrupted intermittently depending on your PC’s

performance. (Depending on model)

• When connecting via a wired LAN, it is recommended to use a CAT

7 cable. (Only when port is provided.)

ENGLISH

Using Button

You can simply operate the TV functions, using the button.

Basic functions

Power On (Press)

Power O

(Press and Hold)

Menu Control (Press

)

Menu Selection (Press and Hold

)

1 All running apps will close, and any recording in progress will stop.

2 You can access and adjust the menu by pressing the button when

TV is on.

3 You can use the function when you access menu control.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust

the Menu items using the button.

Turns the power o.

Changes the input source.

Adjusts the volume level.

Scrolls through the saved programmes.

ENGLISH

Using Magic Remote

Control

(Depending on model)

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

When the message [Magic Remote battery is low. Please change the

battery.] is displayed, replace the battery.

To replace batteries, open the battery cover, replace batteries (1.5VAA)

matching the and ends to the label inside the compartment,

and close the battery cover. Be sure to point the magic remote toward

the remote control sensor on the TV.

1 1

(Some buttons and services may not be provided depending on models

or regions.)

To use the button, press and hold for more than 1 second.

(POWER) Turns the TV on or o.

(STB POWER) You can turn your set-top box on or o by adding

the settop box to the universal remote control for your TV.

Number buttons Enters numbers.

Accesses the [Quick Help].

(DASH) Inserts a between numbers such as 2-1 and 2-2.

Accesses the saved programmes list.

(MORE ACTIONS) Displays more remote control functions.

Edits QUICK ACCESS

- QUICK ACCESS is a feature that allows you to enter a specied app

or Live TV directly by pressing and holding the number buttons.

Audio descriptions function will be enabled.

Adjusts the volume level.

(MUTE) Mutes all sounds.

(MUTE) Accesses the [Accessibility] menu.

Scrolls through the saved programmes.

(Voice recognition) Network connection is required to use the

voice recognition function.

Check for recommended content. (Some recommended services may

not be available in some countries.)

(Voice recognition) Speak while pressing and holding the

button to use the voice recognition feature.

(HOME) Accesses the Home menu.

(HOME) Shows the previous history.

(Q. Settings) Accesses the Quick Settings.

(Q. Settings) Displays the [All Settings] menu.

Wheel (OK) Press the center of button to select a menu. You

can change programmes by using button.

(up/down/left/right) Press the up, down, left or right

button to scroll the menu. If you press buttons while

the pointer is in use, the pointer will disappear from the screen and

Magic Remote will operate like a general remote control. To display

the pointer on the screen again, shake Magic Remote to the left and

right.

(BACK) Returns to the previous level.

(BACK) Clears on-screen displays and returns to last input

viewing.

Shows programme guide.

Streaming Service buttons Connects to the Video Streaming

Service.

Shows the previous history.

(INPUT) Changes the input source.

(INPUT) Accesses the [Home Dashboard].

Displays the set-top box Home menu.

- When you are not watching via a set-top box: the display changes

to the set-top box screen.

, , , These access special functions in some

menus.

Runs the record function.

, (Control buttons) Controls media contents.

ENGLISH

Registering Magic Remote Control

How to register the Magic Remote Control

To use the Magic Remote, rst pair it with your TV.

1 Put batteries into the Magic Remote and turn the TV on.

2 Point the Magic Remote at your TV and press the Wheel (OK) on

the remote control.

* If the TV fails to register the Magic Remote, try again after turning

the TV off and back on.

How to deregister the Magic Remote

Control

Press the (BACK) and (HOME) buttons at the same time, for

ve seconds, to unpair the Magic Remote with your TV.

* Press and hold the button for more than 5 seconds to disconnect

and re-register the Magic Remote at the same time.

• It is recommended that an Access Point (AP) be located

more than 0.2 m away from the TV. If the AP is installed

closer than 0.2 m, the Magic remote control may not

perform as expected due to frequency interference.

• In Analogue TV and some countries, some remote control

buttons may not work.

• Do not mix new batteries with old batteries. This may

cause the batteries to overheat and leak.

• Failure to match the correct polarities of the battery

may cause the battery to burst or leak, resulting in re,

personal injury, or ambient pollution.

• This apparatus uses batteries. In your community there

might be regulations that require you to dispose of these

batteries properly due to environmental considerations.

Please contact your local authorities for disposal or

recycling information.

• Batteries inside or inside the product shall not be

exposed to excessive heat such as sunshine, re or the

like.

User Guide

For more information about this TV, read the USER GUIDE embedded in

the product.

• To open the USER GUIDE → → [Support] → [User

Guide]

Troubleshooting

Cannot control the TV with the remote control.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote

control.

• Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

• Check the power control settings. The power supply may be

interrupted.

• Check if the auto-o function is activated on the settings related

time.

• If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), no signal is detected.

• Turn the TV o/on using the remote control.

• Reconnect the HDMI cable.

• Restart the PC with the TV on.

ENGLISH

Abnormal Display

• If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

• This panel is an advanced product that contains millions of pixels.

You may see tiny black dots and/or brightly coloured dots (white,

red, blue or green) at a size of 1ppm on the panel. This does not

indicate a malfunction and does not aect the performance and

reliability of the product.

This phenomenon also occurs in third-party products and is not

subject to exchange or refund.

• You may nd dierent brightness and colour of the panel

depending on your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel.

It is not related with the product performance, and it is not

malfunction.

Generated Sound

• “Cracking” noise: A cracking noise that occurs when watching or

turning o the TV is generated by plastic thermal contraction due

to temperature and humidity. This noise is common for products

where thermal deformation is required.

• Electrical circuit humming/panel buzzing: A low level noise is

generated from a high-speed switching circuit, which supplies a

large amount of current to operate a product. It varies depending

on the product.

This generated sound does not aect the performance and

reliability of the product.

• Make sure to wring any excess water or cleaner from

the cloth.

• Do not spray water or cleaner directly onto the TV screen.

• Make sure to spray just enough of water or cleaner onto a

dry cloth to wipe the screen.

ENGLISH

Specications

(Depending on country)

Broadcasting Specifications

Digital TV Analogue TV

Television system DVB-T/T2, DVB-C, DVB-S/S2

PAL B/B, PAL B/G, PAL D/K,

PAL-I,

SECAM B/G, SECAM D/K,

NTSC-M

Channel coverage

(Band)

DVB-S/S2

DVB-C

DVB-T/T2

46 ~ 862 MHz

950 ~ 2,150 MHz 46 ~ 890 MHz

VHF III : 174 ~ 230 MHz

UHF IV : 470 ~ 606 MHz

UHF V : 606 ~ 862 MHz

S Band II : 230 ~ 300 MHz

S Band III : 300 ~ 470 MHz

Maximum number of

storable programmes

6,000 3,000

External antenna

impedance

75 Ω

1 Only DVB-T2/C/S2 support model only.

Wireless module(LGSBWAC94)Specications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range Output Power (Max.)

2,400 to 2,483.5MHz

5,150 to 5,725MHz

5,725 to 5,850MHz

17.5dBm

18dBm

12dBm

Bluetooth

Frequency range Output power(Max.)

2,400 to 2,483.5MHz 9dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is congured for the regional

frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20cm between the device and the body.

* IEEE 802.11ac is not available in all countries.

ENGLISH

(Australia and New Zealand region only)

The use of the 5,150 – 5,350 MHz band is restricted to indoor use only. This restriction exists in the countries Australia (AU) and New Zealand (NZ).

(For Wi-Fi/Bluetooth built-in model or Wi-Fi built-in model)

“RF Radiation Exposure Statement

This equipment shall be installed and usedat a minimum distance of 20 cm from the human body.”

Environment condition

Operating Temperature 0°C to 40°C

Operating Humidity Less than 80%

Storage Temperature -20°C to 60°C

Storage Humidity Less than 85%

• The energy information provided with the product is indicated in accordance with the regulations of each country. (Depending on Country)

- The Energy consumption is measured in accordance with IEC 62087.

• Actual Energy consumption may vary depending on factors such as the type of video content being played and TV settings.

• For information of the power supply and power consumption, refer to the label attached to the product. (Depending on country)

- The typical power consumption is measured in accordance with IEC 62087 or each country’s energy regulations.

* On some models, the label is inside the external device connection terminal cover.

* Depending on the model or country, the typical power consumption may not be on label.

ENGLISH

Open Source Software

Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source

licenses, that is contained in this product, please visit

http://opensource.lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

opensourc[email protected].

This oer is valid for a period of three years after our last shipment of

this product. This oer is valid to anyone in receipt of this information.

Licenses

(Magic Remote supported models only)

(Australia region only)

Freeview Plus provides access to content and services from the

Freeview networks. The Freeview Plus service provides a 7 + day

EPG, all available Catch Up TV, recommendations and the ability to

set reminders and favourites. Freeview Plus is available by pressing

the green button on the remote.

* Freeview Plus uses HbbTV technology which combines broadcast

and broadband. It requires an internet connection. Normal data

usage charges and conditions apply.

ENGLISH

Important Information for

Preventing Image Retention

OLED is a self-emissive technology, which brings many signicant

benets to image quality and performance. As with any self-emitting

display, it is possible for users of OLED TVs to experience temporary

image retention under certain conditions, such as when displaying a

static image on the screen for a long time. LG OLED TVs incorporate

dedicated functions that protect the screen from possible image

retention.

If a static image persists on screen, screen brightness is automatically

reduced in specic areas of, or across the entire screen. Once the static

image disappears, screen brightness will automatically return to its

prior setting. This is not a product malfunction.

Examples of Images that may Cause

Image Retention

• Still images or xed images containing certain information

that are displayed uninterrupted on the screen, such as channel

numbers, station logos, program titles, news or movie subtitles,

and headlines.

• Fixed menu or icons for video game consoles or broadcasting

set-top boxes.

• Black bars shown on the left, right, top, or bottom of the screen,

such as in images with a 4:3 or 21:9 ratio.

Recommended Measures for

Preventing Image Retention

• Avoid watching a video displaying an image as listed above for

extended periods of time.

• Adjust your TV settings as below when turning on a video

exhibiting an image as listed above for extended periods of time.

- → → [Picture] → [Picture Mode Settings] →

[Picture Mode] → [Eco] / [APS] (Depending on country)

- → → [Picture] → [Picture Mode Settings] → [OLED

LIGHT] → Adjust to lower value

- → → [Picture] → [OLED Screen Saver] → [Logo

Luminance Adjustment] → [High]

• Turn o the menu bar of an external device, such as a set-top

box, to prevent long-term display of the menu bar of such device.

(Please refer to the manual of the applicable external device for

instructions.)

• Adjust the settings as below when watching a video constantly

showing black bars on the left, right, top or bottom, in order to

remove the black bars.

- → → [Picture] → [Aspect Ratio Settings] → [Aspect

Ratio] → [Vertical Zoom] or [4-Way Zoom]

Information on Functions

Supporting Image Quality in

Relation to Temporary Image

Retention

• LG OLED TVs provide a feature called Pixel Refresher, which helps to

prevent temporary image retention.

• When the accumulated television viewing time reaches 2,000

hours or more (this is equivalent to watching TV for ve hours a

day over the course of a year), Pixel Refresher will be automatically

activated once your TV is turned o. When turning o your TV, a

notice will appear on the screen informing the activation of Pixel

Refresher. This feature will run for an hour while your TV is turned

o. A horizontal line may appear at the top or bottom of the screen

when the process is almost nished.

• You may also manually activate Pixel Refresher via the TV menu:

→ → [Picture] → [OLED Screen Saver] → [Pixel

Refresher].

• Whenever you watch your TV for more than four cumulative hours,

Pixel Refresher will be automatically activated for a few minutes

once your TV is turned o. (Note: Pixel Refresher will not be

activated if the power cord of your TV is not plugged in or the main

power is o.)

Page is loading ...

LG OLED65GXPTA User manual

Brand: LG

Model: OLED65GXPTA

Type: User manual

This manual is also suitable for

Download PDF

report

LG OLED65GXPTA User manual

This manual is also suitable for

LG OLED65GXPTA User manual

Other documents