Askoll pure m User manual

PURE

M

L

XL

LED

AQUARIUM KIT

Instruction manual

Manuale di istruzioni

Manuel d’instructions

Bedienungsanleitung

Handleiding

EASYAQUARIUM

3

EN

Congratulations!

By purchasing an Askoll PURE

LED

Aquarium you will not only enjoy

a fully made-in-Italy design that harmonises well with several interior

design styles, but you will also be able to rely on a product that con-

centrates the best of Askoll technology, a company that can boast

more than thirty years of experience in the design and production of

articles for aquariums and ponds.

In just a few minutes, after starting installation, we are sure that you

will appreciate a product conceived in every detail to make any op-

eration easy and fast. You will enjoy even more the moment in which

you will be able to dedicate your time to create a nature corner in

your new Askoll PURE

LED

Aquarium and you will be able to count on

cutting edge devices to preserve the beauty of the aquatic world over

time, in a simple way.

Before starting, kindly read and follow the warnings and hints con-

tained in this manual carefully.

To choose sh, plants, and the arrangement suitable for your aquar-

ium, follow the suggestions of an expert retailer.

To enhance as much as possible the unique style of your Askoll

PURE

LED

Aquarium, Askoll recommends using the aquarium stands

specically created for this product line.

N.B.: For ease of reference, this manual shows the PURE L

LED

model

aquarium.

1. IMPORTANT SAFETY INFORMATION

The product has been designed and manufactured in conformity

with the current and applicable directives to ensure safe use and

operation throughout its life cycle. Using the product incorrectly (not

in conformity with the instructions given in this manual) can damage

the product and poses a safety risk for the user.

WARNING

Before using the product kindly read and understand

this instruction manual in all its parts.

This manual is an integral part of the product: keep it

for future reference.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Chil

-

dren shall not play with the appliance.

Cleaning and user maintenance shall

not be made by children without super

-

vision.

WARNING

To avoid electric risk:

Each power cable of the electric devices has to show a

drip loop positioned lower than the plug-outlet connec-

tion point in order to prevent any drop from reaching

such point.

The electric devices plug and outlet should not get wet.

Should the plug or outlet of any of the electric devices

become wet, do not disconnect the cable. Disconnect

power supply to the electric system acting on the main

switch.

Disconnect the plugs of the electric devices from the

outlets before handling the product and/or immersing

the hands in water.

Never pull the cable of the electric devices to discon-

nect the plugs from the outlets. To disconnect them,

grab the plugs and pull them.

The product has glass components.

Handle with care and place it according to the instruc-

tions of this manual avoiding to lean the tank directly

on the edges.

To avoid instability risk: check with a level that the sup-

port surface of the product is horizontal.

Do not lean the product on inclined surfaces.

After installation, do not move the product.

If necessary, move it only if the tank is completely

empty.

Do not connect the electric devices of the product to

the mains before having completed the installation or

having repositioned the same after maintenance op-

erations. Do not use the thermal heater and the pump

dry.

To avoid the risk of burns:

After disconnecting the plug, let the hot parts of the

thermal heater (about 30 minutes) and of the lighting

unit (about 5 minutes) cool down, before handling

them. On the thermal heater, the warning light indi-

cates only that the heating phase is active. When the

warning light is off, it does not mean that the thermal

heater is cool.

Check that the water level is always included in the

min. and max. level range indicated on the label.

After maintenance operations, if necessary, restore

the proper water level.

4

PURE Aquarium KIT

CAUTION

Use the product exclusively as decorative aquarium

for indoor domestic use.

Each component is an integral part of the product.

It shall not be used on other products.

Do not use the product for use with foodstuffs.

Do not use the product as terrarium.

Do not use the product, if damaged and/or disassem-

bled.

Do not damage and/or remove the sealant positioned

on the joints of the tank glasses (edge seals).

Do not lean any rocks, stones or other heavy decorat-

ing elements directly on the bottom of the tank.

Do not place any item on the product.

Verify the integrity of the product before pouring water

into the tank.

The thermal heater must always be immersed at least

up to the minimum level marked on the same.

Install the electric devices of the product observing the

voltage and frequency values shown on the devices

and the temperature ones specied among the techni-

cal data under par. 3.3.

Connect the electric devices to mains protected by a

residual current device with a sensitivity ≤ 30 mA.

After maintenance operations, if necessary, dry the

external parts of the product and the stand.

To protect the polished surfaces of the product from

scratches and scrapes, pay utmost care when clean-

ing and handling the same.

CAUTION

Do not cut the power cables.

Power cables cannot be repaired. If the cable is dam-

aged, the product has to be discarded.

Do not use extension cables.

If the length of the power cable of the electric devices

is not sufcient, refer to a qualied electrician.

Do not try to repair any product component: in case of

damage replace the damaged component with origi-

nal spare parts (see chap. 9).

2. CONTENTS

1. IMPORTANT SAFETY INFORMATION page 3

2. CONTENTS 4

3. PRODUCT SPECIFICATIONS 4

4. PREPARING THE PRODUCT FOR USE 7

5. STARTING UP THE SYSTEM 8

6. MAINTENANCE AND CLEANING 11

7. TROUBLESHOOTING 13

8. STORAGE AND REPACKING 13

9. OPTIONAL MODULES AND SPARE PARTS 13

10. PRODUCT DECOMMISSIONING 14

3. PRODUCT SPECIFICATIONS

3.1. Product identication

Name

Components

Askoll PURE

LED

Aquarium KIT

Model

PURE M

LED

PURE L

LED

PURE XL

LED

Lighting unit

Model

LED UNIT

M

LED UNIT

L

LED UNIT

XL

Type T-52043 T-52063 T-52083

Thermal

heater

Model THERM L (100W)

Type D-38100

Pump

Model

PURE

PUMP M

PURE

PUMP L

PURE

PUMP XL

Type C-04311

5

EN

9

10

8

11

FRONT

1

2

3

4

5

6

7

1) Glass tank

2) Edge seals (glass sealant)

3) Light cover door

4) Light cover

5) Filter cover

6) Filter cover door

7) Timer

8) Led Driver

9) Lighting unit cable

10) Lighting unit

11) Decorative trim

1

3.2. Names of components and contents of package

Check that the package contains all the components shown in the following gures.

6

PURE Aquarium KIT

12

27

14

13

17

29

31

30

28

18

12) Frame

13) Thermal heater (with glass tube)

14) Heater bracket with suction cups

15) CO

2

tube connection

16) Fairlead seat

17) Cable guide

18) Pump unit

19) Intake tube

20) Volute

21) Delivery for circulation in the tank

22) Delivery tube

23) Impeller

24) Pump gasket

25) Pump motor

26) Delivery (water outlet nozzle)

27) Accessories compartment

28) Chemical cartridges (in bag):

Model PURE M and L

LED

= 2 3ACTION cartridges

Model PURE XL

LED

= 4 3ACTION cartridges

29) Ceramic cylinders (in bag)

30) Chemical ltration separator

31) Biological baskets with cover (for ceramic cylin-

ders):

Model PURE M

LED

= 1 basket

Model PURE L

LED

= 2 baskets

Model PURE XL

LED

= 3 baskets

32) Baskets for mechanical ltration sponges:

Model PURE M

LED

= 1 basket

Model PURE L

LED

= 2 baskets

Model PURE XL

LED

= 3 baskets

33) Mechanical ltration sponges

2

26

22

25

19

20

23

24

16

15

32

21

33

7

EN

3.3. Technical data

Description

PURE

M LED

PURE

L LED

PURE

XL LED

Capacity

L 44 68 94

Imp gal 9.68 14.96 20.68

Product weight kg 8.8 14.1 19.2

Max. weight with water kg 70 105 150

Height cm 43.5 43.5 43.5

Width cm 36 56 76

Depth cm 36 36 36

Water temperature

(min. / max.)

°C from +5 to +35

PUMP / LIGHTING UNIT / THERMAL HEATER

Power supply V / Hz

See data provided on the

individual electric devices

making up the product.

Consumption W

IP protection rating

4. PREPARING THE PRODUCT FOR USE

4.1. Unpacking

WARNING

The product has glass components.

Handle with care and place it according to the instruc-

tions of this manual avoiding to lean the tank directly

on the edges.

1) Open the carton’s top aps and remove the polystyrene sheet.

2) Extract the product as indicated on the packaging itself. Always

handle it with care.

3) Place it on a at, smooth and clean surface; take care not to

scratch or damage the glass tank bottom.

4) Remove the transparent lm on the covers and upper frame.

5) Remove the lighting and lter covers from the frame (g. 3) and

place them on a at, clean surface without scratching them.

6) Remove the pump unit (g. 4) and place it on a at surface.

7) Remove the frame from the tank (g. 5) and place it on a at,

clean surface without scratching it.

8) Carefully remove the thermal heater and led driver from their

packaging inside the tank, along with the cable guide.

9) Dispose of the packaging material in observance of local reg-

ulations.

10) Check that the product has all the components indicated in par.

3.2.

4.2. Positioning

The product must be positioned with care, in observance of the fol-

lowing instructions:

WARNING

To avoid instability risk: check with a level that the sup-

port surface of the product is horizontal.

Do not lean the product on inclined surfaces.

CAUTION

It is advisable to place the product on the foreseen

aquarium stand. Alternatively, use a sturdy support

able to bear the maximum weight set for the product

(see technical data par. 3.3). Such support must have

a levelled, smooth and clean support surface.

In order not to ease algae proliferation: place the

product far from heat sources and direct exposure to

sunlight.

1) Position the product so that the wording “FRONT” is at the front

and at a distance from the power outlet which enables each

electrical equipment cable to have a drip loop.

2) Remove the “FRONT” label and dispose of it as required by local

regulations.

3 4 5

8

PURE Aquarium KIT

4.3. Assembly

CAUTION

To prevent the risk of scratching the product: clean it

exclusively using a soft cloth moistened with water. Do

not use abrasive products, toxic substances or deter-

gents.

1) Clean the tank with a cloth moistened with water (g. 6).

2) Prepare the tank bottom (sand or other suitable material) ac-

cording to the arrangement desired.

3) Install the thermal heater with its provided bracket (g. 7). IM-

PORTANT: For proper installation, make sure the adjustment

knob is below the bottom edge of the decorative trim. Place

the thermal heater in the aquarium and press its suction caps

against the wall so that they adhere. Set the desired water tem-

perature using the adjustment knob referred to the graduated

scale in °C (g. 8).

4) Restore the frame to the tank.

5) Unwind the thermal heater cable and route it out of the tank via

the pump compartment (g. 9).

6) Restore the pump in its compartment, tidy away the thermal

heater power cable (g. 10).

7) Pick the baskets for the mechanical ltration sponges. Take out

the sponges, rinse them under running water and replace them

in the baskets (g. 11).

8) Pick the biological baskets with their cover (g. 12).

9) Pick the ceramic cylinders and a 3ACTION cartridge. For the XL

model, use 2 3ACTION cartridges.

10) Open the bags containing the ceramic cylinders in a sink, then

pour the cylinders into the biological baskets and rinse them un-

der running water; also rinse the 3ACTION cartridge after taking

it out of its bag (g. 13).

11) Place the biological baskets, the baskets for the mechanical

ltration sponges and the 3ACTION cartridge back into the pro-

vided spaces in the frame (g. 14).

12) Dispose of the plastic bags in observance of local regulations.

13) Restore the light cover to the frame after removing the sticker

securing its power cable (g. 15).

14) Route the power cables for the three electrical devices (lighting

unit, pump unit and thermal heater) out of the tank through the

fairlead seat (g. 16).

15) Restore the lter cover to the frame and hook up the lighting unit

to the led driver with its connector (g. 17).

16) Gather all cables into the provided cable guide (g. 18).

4.4. Installation

WARNING

Do not connect the electric devices of the product to

the mains before having completed the installation. Do

not use the thermal heater and the pump dry.

After installation, do not move the product.

If necessary, move it only if the tank is completely

empty.

CAUTION

Do not lean any heavy objects on the intake tube.

Take care not to allow the material on the tank bot-

tom (sand, etc.), leaves, plants and other objects to

obstruct the intake grilles at the end of the intake tube.

1) Open the light cover and slowly ll the tank ⅓ full, then install the

decorations and aquatic ora.

2) Slowly ll the tank to between the min and max marks on the

label inside the tank itself (g. 19).

3) Close the light cover and check the tank for leaks.

5. STARTING UP THE SYSTEM

5.1. Routine operation

WARNING

To avoid electric risk, each power cable of the electric

devices has to show a drip loop positioned lower than

the plug-outlet connection point in order to prevent any

drop from reaching such point.

1) Read the warnings in Chap. 1.

2) After having connected the plug of each electric device verify the

operation of the same

(in case of malfunction refer to chap. 7):

• Water should ow out of the delivery.

• The warning light of the thermal heater should turn on if the

water temperature is lower than the setpoint.

• The programming timer should be on, with its two rst digits

ashing.

5.1.1. Programming the timer and lighting system

PURE

LED

aquariums are equipped with a new digital timer with a

simple interface (g. 20) which has several functions:

• Light on / off in manual mode.

• Light on / off in automatic mode, at set times.

• Rolling Filtration Timer (RFT), which reminds the user to replace

the 3ACTION cartridge every 15 days to keep the aquarium in

the best condition.

The timer has three touch sensitive buttons, 4 status icons and 4

digital digits. If you set automatic light on/off times, the unit runs a

daily cycle with the following steps:

1) Day light on, the brightness slowly increases over around 30

minutes (dawn effect).

2) Day light off, the brightness slowly decreases over around 30

minutes (dusk effect).

3) Once the day light has turned off completely, the blue night light

turns on for about 3 hours (moon effect).

4) After three hours, the system shuts off the night light too and all

lights stay off until the next daily cycle starts.

You can always turn the light on and off manually, even if the timer is

set to automatic mode.

9

EN

6

7

3

0

1

9

2

4

2

7

8

9

10

11

12

13 14

15

16 17

18

max

min

PURE

19 20

10

PURE Aquarium KIT

There is also a demo mode (DEMO), which simulates the complete

daily cycle in a few seconds to highlight the potential off the led

lighting system when controlled by the integrated timer (point F).

IMPORTANT

Turning the light off manually with the button on the Timer and

turning the light off automatically at the set time do not disconnect

the lighting unit from the power supply.

The PURE

LED

aquarium timer does not need batteries. If there is a

mains power failure, the system maintains the user settings for at

least 12 hours.

A. Setting the clock time on rst start up (hours and

minutes)

Once the lighting unit is connected to the power supply, the timer

waits for the time to be set (it displays icon and the two hour

digits ash).

1) Set the hour by pressing

to increase and to decrease the

setting. Then press

to set the minutes.

2) Set the minutes by pressing

to increase and to decrease

the setting. Press

to conrm. The time has now been set.

If you do nothing, the lighting system is set by default to turn on at

10:00 and turn off at 18:00. To set the on/off times to your preference

or to set the only manual mode, refer to point C.

B. Manual mode

Press to turn on the day light ( icon on), the night light ( icon

on) and turn the light off completely, in that sequence.

C. Programming the automatic light on/off times

1) Hold down button until the text “light” displays (wait for the

countdown 3..2..1  “light” to terminate).

2) The time digits will now display “Auto” and icons and will

ash. To set the only manual mode, press until the text “man”

displays. Conrm by pressing .

3) Once you have set automatic mode “auto”, icon and the hour

digits will ash. Set the on time (hour and minutes) in same way

as for the clock time (points 1 and 2, par. A).

4) Once you have set the on time, icon and the hour digits will

ash. Set the off time (hour and minutes) in same way as for the

clock time (points 1 and 2, par. A).

5) Once you have nished, the timer will display the clock time

again.

6) The timer is now programmed to run the automatic daily light

cycle, as indicated at the start of this chapter.

D. Changing the clock time (hours and minutes)

If you need to change the clock time, proceed as follows:

1) Press and hold down until the clock digits display “time” (you

must wait for 2 countdowns to complete: 3..2..1  “light” 

3..2..1  ”time”).

2) The icon and the hour digits will ash: set the clock time

(hours and minutes) as indicated in par. A.

E. Turning the RFT function on and off

The RFT is on by default (On). To turn it on/off, proceed as follows:

1) Press and hold down until the clock digits display “RFT” (you

must wait for 3 countdowns to complete: 3..2..1  “light” 

3..2..1  ”time”  3..2..1  ”RFT”).

2) The clock digits display “On” and icon ashes; press to

deactivate (OFF) or activate (ON) the RFT function. Conrm by

pressing .

3) Once you have nished, the timer will display the clock time

again.

When the RFT function is on, the timer will ash every 15 days to

remind you to do scheduled maintenance. To reset the indication,

press

.

F. Turning the DEMO function on and off

1) Hold down buttons and simultaneously until the clock dig-

its display “DEMO” (you must wait for the countdown 5..4..3..2..1

 “DEMO” to terminate). The DEMO function is now active.

2) To turn DEMO mode off, press . The timer will display clock

time again.

G. Restoring the factory defaults (timer reset)

1) Press and hold down buttons and simultaneously until

the clock digits display “RSET” (you must wait for 2 countdowns

to complete: 5..4..3..2..1  “DEMO”  5..4..3..2..1  ”RSET”).

2) The timer will now restore the factory default settings.

5.1.2. Filtration

CAUTION

Always close the lter cover after the necessary oper-

ations have been performed, to prevent algae growing

on the lters due to their exposure to direct light.

Aquarium water, to provide the best habitat for sh and plants, must

be ltered continuously with mechanical, biological and chemical

ltration.

Mechanical ltration, which uses double layer sponges, removes

suspended particulates to keep the water clear. You can always

check the degree to which the sponges are soiled by simply opening

the lter cover.

Biological ltration, done by the nitrifying bacteria which grow in

the pores of the ceramic cylinders, minimises the level of toxic chem-

icals in the water, which are harmful for the aquatic fauna, transform-

ing the ammonia produced by the sh into nitrates. It takes around

4 weeks for a sufcient amount of bacteria for effective purication

to develop in the ltration media. This is why the rst month of the

aquarium’s life is critical, and the sh should be added only gradually,

to allow the nitrifying bacteria to take hold and multiply to a suitable

level.

Chemical ltration is done by the 3ACTION cartridge, which con-

tains a special mix of three ingredients:

• Activated carbon for purifying the previously ltered water from

bad odours, colourants, pharmacological residues and other un-

desired compounds.

11

EN

• Anti-nitrates and anti-phosphates for effectively removing from

the water nitrates and phosphates, which are among the major

causes of algae proliferation.

Replacing the 3ACTION cartridge regularly (par. 6.2) allows the ma-

jor undesired compounds to be kept under control and effectively

combats the growth of algae and keeps the water clear and trans-

parent.

REMARK

In seawater aquaria, the nitrate removal function is not effective.

5.1.3. Heating

WARNING

To avoid the risk of burns:

After disconnecting the plug, let the hot parts of the

thermal heater (about 30 minutes) and of the lighting

unit (about 5 minutes) cool down, before handling

them. On the thermal heater, the warning light indi-

cates only that the heating phase is active. When the

warning light is off, it does not mean that the thermal

heater is cool.

CAUTION

The thermal heater is factory calibrated. Variables like

low ambient temperature, large temperature uctua-

tions, lack of covers, positioning of the product close

to cooling sources, may require a higher power to pro-

vide for a better temperature control.

Prevent the bottom (sand or other material), plants and

any other items present in the aquarium from getting

in contact with the thermal heater. It is necessary to

assure a free water circulation around the glass tube.

Install the product close to the pump (g.9) to ensure

that the heated water is distributed evenly and com-

pletely throughout the aquarium.

The thermal heater allows adjusting aquarium water temperature

(from 18°C to 31°C) using the adjustment knob referred to the grad-

uated scale (g. 8). Once it has been started up for the rst time and

the water has reached the setpoint, the thermal heater will keep the

temperature constant by turning off and on as needed. Wait for the

water to reach the temperature set on the thermal heater before put-

ting sh or other animals into the aquarium. Check the temperature

with an aquarium thermometer (not provided).

REMARK

The thermal heater only guarantees water temperature control

when the set temperature is higher than the ambient temperature.

The maximum temperature rise (Δt) of water in relation to the am-

bient temperature is around 10 °C.

5.2. In case of power failure

Power failures have the following effects:

• Gradual reduction, after a few hours, of the effectiveness of the

biological lter, thus potentially damaging the aquarium eco-sys-

tem.

• The timer may need reprogramming if the power failure lasts

more than 12 hours or so.

• The water temperature may fall in proportion to the duration of

the power failure.

For malfunctions, refer to Chap. 7.

6. MAINTENANCE AND CLEANING

WARNING

To avoid electric risk:

Disconnect the plugs of the electric devices from the

outlets before handling the product and/or immersing

the hands in water.

Never pull the cable of the electric devices to discon-

nect the plugs from the outlets. To disconnect them,

grab the plugs and pull them.

Do not connect the electric devices of the product to

the mains before having completed the installation or

having repositioned the same after maintenance op-

erations. Do not use the thermal heater and the pump

dry.

To avoid the risk of burns:

After disconnecting the plug, let the hot parts of the

thermal heater (about 30 minutes) and of the lighting

unit (about 5 minutes) cool down, before handling

them. On the thermal heater, the warning light indi-

cates only that the heating phase is active. When the

warning light is off, it does not mean that the thermal

heater is cool.

Check that the water level is always included in the

min. and max. level range indicated on the label.

After maintenance operations, if necessary, restore

the proper water level.

Do not use detergents or other chemical products

which may damage the product's components or con-

taminate the aquarium itself.

CAUTION

Always close the lter cover after the necessary oper-

ations have been performed, to prevent algae growing

on the lters due to their exposure to direct light.

In case of saltwater aquariums, perform a frequent

and careful cleaning (at least once a month) of the

parts affected by saline condensate.

12

PURE Aquarium KIT

6.1. Maintenance and cleaning jobs

Observe the indicated maintenance and cleaning schedule to keep

your product in excellent working order.

Frequen-

cy

Part Job

Every

week

Mechanical

ltration

Visually inspect the sponges; if they

are clogged, rinse them out or replace

them

Tank

Check that the water level is between

the MIN and MAX marks and top it up

as needed.

Every 15

days

Chemical

ltration

Replace the 3ACTION cartridge (2

cartridges for the XL model) (par. 6.2

Rolling Filtration System)

Every

month

Mechanical

ltration

Replace the mechanical lter sponge

(2 sponges for the XL model). For the

L and XL models, replace the spong-

es closest to the water outlet nozzle

(par. 6.2)

Every 6

months

Pump unit Clean the pump unit (par. 6.3)

6.2. Rolling Filtration System

To keep the lters working properly and ensure the best water con-

ditions in the aquarium, Askoll recommends that you replace the

sponges and cartridges according to a specic maintenance sched-

ule, the Rolling Filtration System (RFS).

This is very easy to do with the original Askoll maintenance kits,

available from your retailer (see product code in Chap. 9).

Two kits are available:

• Askoll PURE FILTER MEDIA KIT M-L-XL, containing 1 me-

chanical ltration sponge and 2 3ACTION cartridges (1 kit per

month for PURE M and PURE L aquariums, 2 for the PURE XL

aquarium);

and:

• Askoll PURE FILTER MEDIA KIT M-L-XL CONVENIENT, con-

taining 4 mechanical ltration sponges and 8 3ACTION cartridg-

es (1 kit every 4 months for PURE M and PURE L aquariums, 1

every 2 months for the PURE XL aquarium);

Replace the sponges and cartridges as follows:

1) After disconnecting the plug of each electric device, open the

lter cover.

2) Remove the sponges and cartridges and dispose of them ac-

cording to local regulations.

3) Replace the sponges and cartridges at the specied intervals

(par. 6.1).

4) Close the lter cover.

The Askoll PURE

LED

timer will remind you every 15 days (icon

ashing) to replace the 3ACTION cartridge/s (Rolling Filtration Timer

– RFT). To turn off the RFT indication, simply press .

To turn off the RFT function, refer to par. 5.1.1. - E.

6.3. Cleaning and servicing the pump unit

1) After disconnecting the plug of each electric device, remove the

lter cover and extract the pump unit cable from the fairlead seat

and cable guide.

2) Extract the pump unit (g. 21).

3) Detach the intake tube and delivery tube (with delivery) from the

volute (g. 22).

4) If necessary, replace the pump (dispose of it as indicated in

Chap. 10), otherwise go to the next step.

5) Turn the pump volute counterclockwise to remove it, then extract

the impeller (g. 23).

6) Rinse the impeller under running water (g. 24).

7) Clean the impeller’s seat carefully with a non-abrasive brush

(g. 25).

8) If necessary, also clean the intake tube, delivery tube and deliv-

ery under running water.

9) Reassemble and restore the pump carefully along with the other

components, proceeding in the reverse order to the disassembly

procedure.

6.4. Cleaning the lighting unit

1) After disconnecting the plug of the lighting unit, remove the lter

cover and the light cover.

2) Place the covers on a surface protected with a cloth so as not

to scratch them.

21 22

23

13

EN

3) If the light cover or the lighting unit (with the timer) need re-

placing, disassemble the two elements by unscrewing the three

screws which keep them together using a suitable Phillips

screwdriver (g. 26).

4) Clean the lighting unit with a damp cloth.

5) Reassemble and reposition the components carefully repeating

the above described procedure in opposite order.

7. TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

The lighting

is not

working

Missing connection of

the led driver to the pow-

er outlet

Connect the led driver

to the power outlet

Missing connection of

the lighting unit to the led

driver

Connect the lighting

unit to the led driver

with its connector

Other Contact your retailer

Water

temperature

low

The thermal heater is not

plugged into its power

outlet

Plug the thermal

heater into its power

outlet

The thermal heater ad-

justment knob is set too

low

Set the temperature

to the correct value

(par. 5.1.3)

The ambient temperature

is too low

Add a supplementary

thermal heater

Other Contact your retailer

No water

ow

The pump is not plugged

into its power outlet

Plug the pump into its

power outlet

The pump is jammed

Clean the impeller

(par. 6.3)

Other Contact your retailer

Low water

ow

The intake tube, pump,

delivery tube or delivery

is clogged

Clean the parts

8. STORAGE AND REPACKING

To store the product:

1) Carefully clean and dry off all parts of the product. The mechan-

ical ltration sponges and the 3ACTION cartridges must be dis-

posed of according to local regulations.

2) Store the product and its components in suitable containers.

3) Keep the product indoors in a dry place, out of the weather and

freezing temperatures.

9. OPTIONAL MODULES AND SPARE PARTS

9.1. Optional modules

The product can be tted with the following optional modules (not

included):

Module Description

ROBOFOOD

programmable sh

feeder

Battery powered programmable sh feeder

which can dispense up to two meals a day

Askoll CO

2

PRO-

GREEN SYSTEM

CO2 enricher

Dispenses CO

2

into the aquarium to pro-

mote plant growth

ASKOLL

ROBOFORMULA

Electronic aquarium treatment dispenser

with Askoll Formula Azure cartridge for

clear water and healthy plants

PURE aquarium

stand

Specically designed, it is the best tting

for the aquarium, enhancing its style and

providing a sturdy and suitable support to

the same

24

25 26

14

PURE Aquarium KIT

9.2. Spare parts

For part numbers in circles refer to g. 1 and g. 2.

Model

PURE M

LED

PURE L

LED

PURE XL

LED

Component Codes

PURE PUMP

pump

20

23

24

25

EUR AB350050 AB350052 AB350054

UK AB350051 AB350053 AB350055

Impeller

23

AB350056 AB350057 AB090006

Led Driver

8

EUR AB350059

UK AB350060

Lighting unit (with timer)

10

AB350061 AB350062 AB350063

Thermal

heater THERM L

(100W)

13

14

EUR AA230003

UK AA230008

Heater bracket with suction

cups

14

AB230001

Delivery and intake KIT

19

22

26

AB350064

Baskets KIT (n. 1 biological

basket for ceramic cylinders,

n. 1 basket for mechanical

ltration sponges, n. 1 chem-

ical ltration separator)

30

31

32

AB350018

Cable guide

17

AB350022

Light cover and

lter cover

4

5

white AB350065 AB350068 AB350071

black AB350066 AB350069 AB350072

burgundy AB350067 AB350070 AB350073

PURE FILTER MEDIA KIT

M, L, XL

28

33

AC350013

PURE FILTER MEDIA KIT

M, L, XL CONVENIENT

28

33

AC350014

Askoll PURE MAX MINI

ceramic cylinders 100g

29

AC350006

10. PRODUCT DECOMMISSIONING

On the package and/or in the product, the symbol indi-

cating the separate collection of electric and electronic

equipment is printed in a visible, readable and indeli-

ble way. It consists of a crossed-out wheeled bin. The

user shall convey the discarded product to the collec-

tion centres in his own Municipality or return it to the retailer when

purchasing a new equivalent product, on a one-against-one basis.

Suitable separate collection, which allows for the following recycling,

treatment and compatible environmental disposal of the discarded

product, contributes to prevent to affect negatively the environment

and the health, besides easing reuse and/or recycling of the material

of which the product is made. Abusive disposal of the product by the

user implies the application of the administrative sanctions set forth

by the regulations in force in the country of disposal.

Page is loading ...

16

PURE Aquarium KIT

ATTENZIONE

Utilizzare il prodotto esclusivamente come acquario

ornamentale per uso domestico in ambiente chiuso.

Ogni componente è parte integrante del prodotto.

Non deve essere utilizzato su altri prodotti.

Non utilizzare il prodotto per uso alimentare.

Non utilizzare il prodotto come terrario.

Non utilizzare il prodotto danneggiato e/o smontato.

Non danneggiare e/o togliere il sigillante posto sulle

giunzioni dei vetri della vasca (guarnizioni bordi).

Non appoggiare direttamente sul fondo della vasca

rocce, sassi o altri elementi ornamentali pesanti.

Non posizionare alcun oggetto sopra al prodotto.

Vericare l’integrità del prodotto prima di inserire l’ac-

qua nella vasca.

Il termoriscaldatore deve sempre essere immerso al-

meno sino al livello minimo riportato sullo stesso.

Installare gli apparecchi elettrici del prodotto rispet-

tando i valori di tensione e frequenza riportati sugli

apparecchi e di temperatura riportati nei dati tecnici

al par. 3.3.

Collegare gli apparecchi elettrici ad una rete di alimen-

tazione elettrica protetta da un interruttore differenzia-

le con una sensibilità ≤ 30 mA.

Dopo le operazioni di manutenzione, se necessario,

asciugare le parti esterne del prodotto e il supporto.

Per preservare le superci lucide del prodotto da graf

e abrasioni, prestare particolare attenzione alla pulizia

e alla manipolazione delle stesse.

ATTENZIONE

Non tagliare i cavi di alimentazione elettrica.

I cavi di alimentazione elettrica non possono essere ri-

parati. Se il cavo è danneggiato il prodotto deve essere

messo fuori servizio.

Non utilizzare cavi di prolunga. Se la lunghezza del

cavo di alimentazione degli apparecchi elettrici è in-

sufciente, rivolgersi ad un elettricista esperto e com-

petente.

Non tentare di riparare alcun componente del prodot-

to: in caso di danneggiamento sostituire il componente

danneggiato con ricambi originali (v. cap. 9).

2. SOMMARIO

1. INFORMAZIONI IMPORTANTI SULLA SICUREZZA pag. 15

2. SOMMARIO 16

3. SPECIFICA DEL PRODOTTO 16

4. PREPARAZIONE DEL PRODOTTO ALL’UTILIZZO 19

5. ISTRUZIONI PER LA MESSA IN FUNZIONE 20

6. MANUTENZIONE E PULIZIA 24

7. ANOMALIE - CAUSE - RIMEDI 25

8. STOCCAGGIO E REIMBALLAGGIO 26

9. MODULI OPZIONALI E RICAMBI 26

10. MESSA FUORI SERVIZIO DEL PRODOTTO 26

3. SPECIFICA DEL PRODOTTO

3.1. Identicazione del prodotto

Denomina-

zione

Componenti

Askoll PURE

LED

Aquarium KIT

Modello

PURE M

LED

PURE L

LED

PURE XL

LED

Unità di

illuminazione

Modello

LED UNIT

M

LED UNIT

L

LED UNIT

XL

Tipo T-52043 T-52063 T-52083

Termoriscalda-

tore

Modello THERM L (100W)

Tipo D-38100

Pompa

Modello

PURE

PUMP M

PURE

PUMP L

PURE

PUMP XL

Tipo C-04311

Page is loading ...

21

IT

6

7

3

0

1

9

2

4

2

7

8

9

10

11

12

13 14

15

16 17

18

max

min

PURE

19 20

Page is loading ...

33

FR

6

7

3

0

1

9

2

4

2

7

8

9

10

11

12

13 14

15

16 17

18

max

min

PURE

19 20

Page is loading ...

40

PURE Aquarium KIT

VORSICHT

Verwenden Sie das Produkt nur als Zieraquarium zum

Hausgebrauch in geschlossenen Umgebungen.

Jede Komponente ist Bestandteil des Produktes.

Sie darf nicht bei anderen Produkten verwendet wer-

den.

Das Produkt darf nicht zusammen mit Nahrungsmitteln

zum Einsatz kommen.

Benutzen Sie das Produkt nicht als Terrarium.

Benutzen Sie das Produkt nicht im beschädigten und/

oder ausgebauten zustand.

Beschädigen Sie die Versiegelung an den Beckenglas-

abdichtungen (Kantendichtungen) nicht und entfernen

Sie das Versiegelungsmittel nicht.

Legen Sie keine Ziersteine oder sonstige schwere Zier-

gegenstände direkt auf den Boden des Beckens.

Legen Sie keine Gegenstände auf dem Produkt ab.

Prüfen Sie das Produkt auf seine Unversehrtheit, bevor

Sie Wasser in das Becken füllen.

Der Aquarienheizer muss stets mindestens bis zum

Mindeststand eingetaucht werden, der auf dem Aquari-

enheizer selbst angezeigt wird.

Montieren Sie die Elektrogeräte des Produkts unter

Einhaltung der Spannungs- und Frequenzwerte, die

auf den Geräten erscheinen, sowie unter Beachtung

der Temperatur, die unter den technischen Daten unter

Abschn. 3.3 angeführt wird.

Die elektrischen Geräte an ein mit einem Fehlerstrom-

schutzschalter mit einer Empndlichkeit von ≤ 30 mA

ausgerüstetes Stromnetz anschließen.

Trocknen Sie nach den Wartungsarbeiten die Teile, die

sich außerhalb des Produktes benden, sowie den Un-

terschrank ab.

Um die polierten Teile vom Produkt vor Kratzern und

Schürfungen zu schützen, achten Sie besonders auf,

wenn Sie sie reinigen und handhaben.

VORSICHT

Schneiden Sie die Stromkabel nicht durch.

Stromkabel dürfen nicht repariert werden.

Sollte ein Kabel beschädigt sein, muss das Produkt

außer Betrieb genommen werden.

Verwenden Sie keine Verlängerungskabel. Reicht die

Länge der Stromkabel der Elektrogeräte nicht aus,

wenden Sie sich an einen Elektrofachmann.

Versuchen Sie nicht, eines der Bestandteile des Pro-

dukts zu reparieren: Tauschen Sie das Bestandteil bei

Beschädigungen mit Originalteilen aus (s. Kap. 9).

2. INHALT

1. WICHTIGE SICHERHEITSBESTIMMUNGEN S. 39

2. INHALT 40

3. PRODUKTSPEZIFIKATION 40

4. VORBEREITUNG DES PRODUKTS FÜR DEN GEBRAUCH 43

5. ANWEISUNGEN FÜR DIE INBETRIEBNAHME 44

6. WARTUNGS- UND REINIGUNGSARBEITEN 48

7. STÖRUNGEN - URSACHEN - MASSNAHMEN 49

8. LAGERUNG UND WIEDER VERPACKUNG 50

9. OPTIONALE MODULE UND ERSATZTEILE 50

10. AUSSERBETRIEBSETZUNG DES PRODUKTS 50

3. PRODUKTSPEZIFIKATION

3.1. Produktkennzeichnung

Bezeichnung

Bestandteile

Askoll PURE

LED

Aquarium KIT

Modell

PURE M

LED

PURE L

LED

PURE XL

LED

Beleuchtungs-

einheit

Modell

LED UNIT

M

LED UNIT

L

LED UNIT

XL

Typ T-52043 T-52063 T-52083

Aquarienhei-

zer

Modell THERM L (100W)

Typ D-38100

Pumpe

Modell

PURE

PUMP M

PURE

PUMP L

PURE

PUMP XL

Typ C-04311

41

DE

9

10

8

11

FRONT

1

2

3

4

5

6

7

1) Glasbecken

2) Kantendichtungen (Glasversiegelung)

3) Klappe Beleuchtungsabdeckung

4) Beleuchtungsabdeckung

5) Filterdeckel

6) Klappe Filterdeckel

7) Zeitschaltuhr

8) Netzteil

9) Stromversorgungskabel für Beleuchtung

10) Beleuchtungseinheit

11) Dekorationsstreifen

1

3.2. Bezeichnung der Bestandteile und Verpackungsinhalt

Überprüfen Sie, dass die Verpackung alle Bestandteile enthält, die auf den folgenden Abbildungen erscheinen.

Page is loading ...

45

DE

6

7

3

0

1

9

2

4

2

7

8

9

10

11

12

13 14

15

16 17

18

max

min

PURE

19 20

Page is loading ...

Askoll pure m User manual

This manual is also suitable for

Askoll pure m User manual

in other languages

Related papers

Other documents