Alto-Shaam 500-3DN Installation Operation & Maintenance

Brand: Alto-Shaam

Model: 500-3DN

Category: Food warmers

Type: Installation Operation & Maintenance

This manual is also suitable for

MN-29742 (Rev. 9) • 12/17

Printed in U.S.A.

W164 N9221 Water Street • P.O. Box 450

Menomonee Falls, Wisconsin 53052-0450 U.S.A.

PHONE: 262.251.3800 • 800.558.8744 U.S.A. / CANADA

FAX:

262.251.7067 • 800.329.8744 U.S.A. ONLY

www.alto-shaam.com

Consult instructions

for operation and use.

500-1DN

500-2DN

500-3DN

500-1D

500-2D

500-3D

Drawer Warmers

Electric

Hot Food Holding

5001D

5002D

5003D

5001DN

5002DN

5003DN

• Installation

• Operation

• Maintenance

2 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Table of Contents

Table of Contents ............................................2

Delivery ...................................................3

Transportation and Damage Claims .............................4

Unpacking .................................................5

Safety Procedures ...........................................6

Installation .................................................8

Electrical Connection .......................................11

Operation .................................................12

General Holding Guidelines ..................................14

Cleaning and Preventative Maintenance ........................15

Food Safety ................................................17

Troubleshooting ............................................18

Service ...................................................20

Wiring Diagrams ...........................................27

Limited Warranty ....................................Back cover

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 3

Delivery

This Alto-Shaam appliance has been thoroughly

tested and inspected to ensure only the highest quality

appliance is provided. Upon receipt, check for any

possible shipping damage and report it at once to the

delivering carrier. See Transportation Damage and

Claims section located in this manual.

This appliance, including unattached items and

accessories, may be delivered in one or more packages.

Ensure all standard items and options have been

received with each appliance as ordered. Save all the

information packed with the appliance. Register the

appliance online at www.alto-shaam.com/en/support/

warranty-registration to ensure prompt service in the

event of a warranty parts and labor claim.

This manual must be read and understood by all

peopleusing or installing the appliance. Contact the

Alto-Shaam Tech Team Service Department if you

haveany questions concerning installation, operation,

or maintenance.

1-800-558-8744; [email protected]

CAUTION

Appliance and accessories may be

heavy. To prevent serious injury, always

use a su icient number of trained and

experienced workers when moving or

leveling appliance and handling accessories.

Environmental Conditions

Operational Environmental Conditions

• Before use, appliance must acclimate to room

temperature in the environment it is placed — 24 hours

isrecommended.

• Ambient temperature range of 60°F to 110°F (16°C to 43°C).

• Relative humidity of less than 95% non-condensation.

• Atmospheric pressure range of 50kPa to 106kPa.

The serial number is required for all inquiries.

Always include both model and serial number(s) in any

correspondence regarding the appliance.

Model: ______________________________________________

Serial number: ______________________________________________

Purchased from: ______________________________________________

Date installed: ____________________ Voltage: _____________

4 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Transportation and Damage Claims

All Alto-Shaam equipment

is sold Free on Board

(F.O.B.) shipping point,

and when accepted by the

carrier, such shipments

become the property of the

consignee.

Should damage occur in shipment, do not put the

appliance into service until the damage has been

inspected by an authorized Alto-Shaam service provider.

Shipping damages are a matter between the carrier and

the consignee. In such cases, the carrier is assumed to

be responsible for the safe delivery of the merchandise,

unless negligence can be established on the part of

theshipper.

1. Make an immediate inspection while the appliance is

still in the truck or immediately a er it is moved to the

receiving area. Do not wait until a er the appliance is

moved to a storage area.

2. Do not sign a delivery receipt or a freight bill until

a proper count has been made and inspection of all

appliances are received.

3. Note all damage to packages directly on the carrier’s

delivery receipt.

4. Make certain the driver signs the delivery receipt. If the

driver refuses to sign, make a notation of this refusal

on the receipt.

5. If the driver refuses to allow inspection, write the

following on the delivery receipt: Driver refuses to

allow inspection of containers for visible damage.

6. Contact the carrier’s of ce immediately upon  nding

damage, and request an inspection. Mail a written

con rmation to the carrier’s of ce with the time, date,

and the personcalled.

7. Save any packages and packing material for further

inspection by the carrier.

8. Promptly  le a written claim with the carrier and

attach copies of all supporting paperwork.

Alto-Shaam will continue our policy of assisting our

customers in collecting claims which have been properly

 led and actively pursued. Alto-Shaam cannot, however,

 le any damage claims, assume the responsibility of any

claims, or accept deductions in payment for such claims.

Record the model and serial number of the appliance for easy

reference. Always refer to both model and serial number in

any contact with Alto-Shaam regarding this appliance.

Model:

______________________________________________

Serial Number:

______________________________________________

Date Installed:

______________________________________________

Voltage:

______________________________________________

Purchased From:

______________________________________________

Alto-Shaam has established a twenty-four

hour emergency service call center to offer immediate

customer access to a local authorized service agency

outside of standard business hours. The emergency

service access is provided exclusively for Alto-Shaam

equipment and is available throughout the United

States through the use of Alto-Shaam’s toll-free

number. Emergency service access is available seven

days a week including holidays.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 5

Unpacking

• Carefully remove the appliance from the carton or crate.

NOTE: Do not discard the carton and other packaging material until you

have inspected the appliance for hidden damage and tested it for

proper operation.

Do not discard this manual. This manual is considered to be part

of the appliance and is to be provided to the owner or manager of

the business or to the person responsible for training operators.

Additional manuals are available from the manufacturer.

• Read all instructions in this manual carefully before installing this

appliance, using the appliance or performing routine maintenance.

Following procedures other than those indicated in this guide to use and

clean the appliance is considered inappropriate and may cause damage,

injury or fatal accidents, in addition to voiding the warranty and relieving

Alto-Shaam of all liability.

• Remove all protective plastic  lm, packaging materials, and accessories

from the appliance before connecting electrical power. Store any

accessories in a convenient place for future use.

6 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Safety Procedures

DANGER

Indicates a hazardous situation that, if not avoided, will

result in death or serious injury.

• The appliance is intended to cook, hold or process foods

for the purpose of human consumption. No other use for

this appliance is authorized and is therefore considered

dangerous. The appliance must not be used to cook

food containing  ammable materials (such as food with

alcohol). Substances with a low  ash point can ignite

spontaneously and cause a  re.

• The appliance is intended for use in commercial

establishments where all operators are familiar with

the purpose, limitations, and associated hazards of this

appliance. Operating instructions and warnings must

be read and understood by all operators and users.

Alto-Shaam recommends regular staff training to avoid

the risk of accident or damage to the appliance. Operators

must also receive regular safety instructions.

• Any troubleshooting guides, component views, and

partslists included in this manual are for general

reference only and are intended for use by quali ed and

trained technicians.

• This manual should be considered a permanent part of

this appliance. This manual and all supplied instructions,

diagrams, schematics, parts lists, notices, and labels must

remain with the appliance if the item is sold or moved to

another location.

NOTICE: Indicates information considered important,

but not hazard-related (e.g., messages relating

to property damage).

Knowledge of proper procedures is essential to the

safe operation of electrically and/or gas energized

equipment. The following signal words and symbols

may be used throughout this manual.

Indicates that referral to operating

instructions is a mandatory action. If

not followed the operator could su er

personalinjury.

Indicates that referral to operating

instructions is recommended to understand

operation of equipment.

NOTICE: For equipment delivered for use in any

location regulated by the following

directive: 2012/95/EC WEEE

Do not dispose of electrical or electronic

equipment with other municipal waste.

WARNING

Indicates a hazardous situation that, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not avoided, could

result in minor or moderate injury.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 7

Safety Procedures

• To prevent serious injury, death or property damage,

the appliance should be inspected and serviced at

least every twelve (12) months by an authorized

service partner or trained technician.

• Only allow an authorized service partner or trained

technician to service or to repair the appliance.

Installation or repairs that are not performed by an

authorized service partner or trained technician, or

the use of non-factory authorized parts will void the

warranty and relieve Alto-Shaam of all liability.

• When working on this appliance, observe precautions

in the literature, on tags, on labels attached to

or shipped with the appliance and other safety

precautions that may apply.

• If the appliance is installed on casters, freedom of

movement of the appliance must be restricted so

that utility connections (including gas, water, and

electricity) cannot be damaged when the appliance

is moved. If the appliance is moved, ensure that all

utility connections are properly disconnected. If the

appliance is returned to its original position, ensure

that retention devices and utility connections are

properly connected.

• Only use the appliance when it is stationary. Mobile

appliance racks, mobile plate racks, transport trolleys,

andappliances on casters can tip over when being

moved over an uneven  oor or threshold and cause

serious injury.

• Always apply caster brakes on mobile appliances or

accessories when these are not being moved. These

items could move or roll on uneven  oors and cause

property damage or serious injury.

• Be extremely careful when moving appliances

because the food trays may contain hot  uids that may

spill, causing serious injury.

• Always open the appliance door very slowly. Escaping

hot vapors or steam can cause serious injury or death.

• If the gas appliance is installed under an exhaust

hood, the hood must be switched On when the

appliance is in use to avoid the build up of combustion

gases. Failure to do so may result in serious injury,

death or property damage.

• Accumulations on the main burners of gas appliances

can result in  ring out of normal sequence. This

delayed ignition creates an alarmingly loud sound.

If your appliance makes an especially loud noise

when starting up, shut down the appliance and call a

quali ed and trained service technician.

• Never place objects near the appliance exhaust vents.

Thisarea is hot and could be a potential ignition

source for a  re.

• Do not allow objects to block or obstruct the area

below the appliance base. This may result in  re,

damage to the equipment or serious injury.

• Do not use the attached hand-held hose to

sprayanything other than the interior of the

appliancecompartment.

• Do not use the attached hand-held hose on the

surface of a hot cooking compartment. The sudden

temperature change can damage the appliance

interior. Allow the appliance to cool to a minimum of

150°F(66°C). Failure to observe this precaution can

void the warranty.

WARNING

To prevent serious personal injury, death,

or property damage:

The appliance must be cleaned thoroughly

to avoid deposits of grease and or food

residue inside the appliance that may

catch fire. If fat deposits and/or food waste

inside the appliance ignite, shut down

the appliance immediately and keep the

appliance door closed to extinguish the

fire. If further extinguishing is required,

disconnect the appliance from the main

power and use a fire extinguisher (do not

use water to extinguish a grease fire!).

Failure to clean the appliance properly

invalidates the warranty and relieves

Alto-Shaam of all liability.

WARNING

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision concerning use

of the appliance by person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

8 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Installation

This Alto-Shaam

appliance must be

installed in a location

that will permit it to

function for its intended

purpose and to allow

adequate clearance

for ventilation,

proper cleaning, and

maintenance access.

1. This appliance must be installed on a stable and

level surface.

2. Do not install this appliance in any area where it

may be affected by any adverse conditions such as

steam, grease, dripping water, high temperatures,

or any other severely adverse conditions.

3. This appliance must be kept free and clear of any

obstructions blocking access for maintenance or

service.

CAUTION

To prevent personal injury or

propertydamage:

Always use hand protection when

operating this appliance to avoid burns.

Metal parts of this equipment become

extremely hot when in operation.

W017

Warning; Hot surface

WARNING

Improper installation, alteration, adjustment, service,

cleaning, or maintenance could result in property

damage, severe injury, or death.

Read and understand the installation, operating and

maintenance instructions thoroughly before installing,

servicing, or operating this equipment.

CAUTION

Appliance and accessories may be

heavy. To prevent serious injury, always

use a su icient number of trained and

experienced workers when moving or

leveling appliance and handling accessories.

WARNING

To prevent personal injury, death or

property damage:

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

Minimum Clearance Requirements

Back 3" (76mm)

Top 2" (51mm)

Le side, Right side 1" (25mm)

Weight (est.)

500-1D 500-2D 500-3D

Net 80 lb (36 kg) 115 lb (52 kg) 150 lb (68 kg)

Ship 90 lb (41 kg) 125 lb (57 kg) 165 lb (75 kg)

500-1DN 500-2DN 500-3DN

Net 67 lb (30 kg) 100 lb (45 kg) 130 lb (59 kg)

Ship 75 lb (34 kg) 112 lb (51 kg) 145 lb (66 kg)

Product Capacity (each drawer)

Full-Size Pan (GN1/1) - 12" x 20" x 6" (305 x 508 x 152mm)

36 lbs (16 kg) Maximum

Oversize Pan - 15” x 20” x 5” (381 x 508 x 127mm)

41 lbs (19 kg) maximum

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 9

Installation

12-5/16"

(312mm)

24-5/8" (624mm)

43-3/8" (1101mm)

24-7/8" (631mm)

26-1/8" (664mm)

25-7/8" (657mm)

11-5/8"

(296mm)

18-15/16" (481mm)

500-1D

500-2D

500-3D

Electrical

Connection

6-3/4" (171mm) FOR

LEG STAND OR 5" (127mm)

CASTER STAND ASSEMBLY

4-7/8" (121mm)

FOR CASTER STAND ASSEMBLY

WITH 3" (76mm) CASTERS

Cord Length:

120V - 5' (1524mm)

208-240V - 8' (2438mm)

230V - 8' (2438mm)

500-1D, 500-2D, 500-3D

Accessories

Built-in Trim Kit

500-1D 5015147

500-2D 5015149

500-3D 5005153

Caster Stand Assembly

- with 5" (127mm) casters 15379

- with 3" (76mm) casters 5010920

Leg Stand Assembly 15380

Pan

Oversize, 15" x 20" x 5" (381 x 508 x 127mm) PN-2123

Full-size, 12 x 20 x 6 (305 x 508 x 152mm) PN-25088

Perforated pan grid

15" x 20" (381mm x 508mm) 1231

12" x 20" (305mm x 508mm) 16642

Cutout Dimensions (for units with built in trim)

Add 3/4” (19mm) to unit height and 1-1/2” (38mm) to unit width

10 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Installation

26-1/8" (664mm)

31-3/16" (792mm)

11-5/8"

(296mm)

18-15/16" (481mm)

500-1DN

500-2DN

500-3DN

6-3/4" (171mm) FOR

LEG STAND OR 5" (127mm)

CASTER STAND ASSEMBLY

4-7/8" (121mm)

FOR CASTER STAND ASSEMBLY

WITH 3" (76mm) CASTERS

8-5/16"

(211mm)

16-11/16"

(423mm)

53-3/4" (1364mm)

24-7/8" (631mm)

Cord Length:

120V - 5' (1524mm)

208-240V - 8' (2438mm)

230V - 8' (2438mm)

Electrical

Connection

500-1DN, 500-2DN, 500-3DN

Accessories

Built-in Trim Kit

500-1DN 5015148

500-2DN 5015150

500-3DN 5015154

Caster Stand Assembly

- with 5" (127mm) casters 55534

- with 3" (76mm) casters 5010921

Leg Stand Assembly 55535

Perforated pan grid, 12" x 20" (305mm x 508mm) 16642

Cutout Dimensions (for units with built in trim)

Add 3/4” (19mm) to unit height and 1-1/2” (38mm) to unit width

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 11

Electrical Connection

1. An identication tag is permanently mounted on the

Drawer Warmer.

2. Plug Drawer Warmer into a properly grounded

receptacle only, positioning the unit so the power

supply cord is easily accessible in case of an

emergency.

Arcing will occur when connecting or disconnecting

the unit unless all controls are in the “Off” position.

3. If necessary, a proper receptacle or outlet

conguration as required for this unit, must be

installed by a licensed electrician in accordance with

applicable, local electrical codes.

This section is provided for the assistance of

qualified and trained service technicians only

and is not intended for use by untrained or

unauthorized service personnel. Failure to

observe this precaution may void the warranty.

WARNING

To prevent serious injury, death, or property

damage, always disconnect the appliance

from the power source before cleaning

orservicing.

WARNING

To prevent serious injury, death, or

property damage:

All electrical connections must be

made by a qualified and trained service

technician in accordance with applicable

electrical codes.

This appliance must be adequately

grounded in accordance with local

electrical codes or, in the absence of local

codes, with the current edition of the

National Electrical Code ANSI/NFPA No.

70. In Canada, all electrical connections

are to be made in accordance with CSA

C22.1, Canadian Electrical Code Part 1 or

local codes.

CE-approved appliances include an

equipotential-bonding terminal marked

with the symbol shown on the le .

Provisions for earthing are to be made in

accordance with IEC:2010 60335-1 section

27 or local codes.

Wire diagrams are located inside the bonnet of the unit.

NOTICE: Where local codes and CE regulatory

requirements apply, appliances must be

connected to an electrical circuit that is

protected by an external GFCI outlet.

Hard wired models:

Hard wired models must be equipped with a country

certi ed external allpole disconnection switch with

suf cient contact separation.

If a power cord is used for the connection of the product an

oil resistant cord like H05RN or H07RN or equivalent must

be used.

Electrical

V Ph Hz A kW

120 1 50/60 5.3 0.64 NEMA 5-15P

15A, 125V plug

208-240 1 50/60 2.7 0.64 NEMA 6-15P

15A, 250V plug

230 1 50/60 2.6 0.59 Plugs rated 250V

CH216P BS 1363 AS/NZS 3112 CEE 7/7

12 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Operation

Before initial use:

Clean both the interior and exterior of the unit with a

clean, damp cloth and mild soap solution. Rinse carefully.

Clean and install the drawer warmer pan(s). The drawer

assembly is completely removable.

Heating Characteristics

The drawer warmer is equipped with a special heating

element. Through this Halo Heat concept, the heating

element is mounted against the walls of the unit to provide

an evenly applied heat source controlled by a digital

control. The design and operational characteristics of

the unit eliminate the need for a moisture pan or a heat

circulating fan. Through even heat application, the quality

of food products is maintained up to several hours or

more.

Food Product Tips

Bread and Rolls

Breads and rolls are traditionally difcult to hold for

prolonged periods due to the very low moisture content

of these products. For best results and longest possible

holding life, it is recommended these products be

placed in a plastic bag while in the warming drawer.

Breads and rolls should be held at a temperature no

higher than 120° to 140°F (49° to 60°C).

Potatoes

For the best results when holding potatoes:

1. Do not overcook.

Regardless of the temperature at which potatoes

are cooked or what type of oven is used, it is

important that this product does not achieve a

nal internal product temperature in excess of

195°F (91°C). Over-cooking will further reduce the

moisture content and consequently, reduce the

holding life. Potatoes should be removed from the

oven when they reach an internal temperature of

approximately 190°F (88°C). Aer they are removed

from the oven, the internal temperature will

continue to increase.

2. Allow potatoes to stabilize before placing in

drawer warmer.

When potatoes are removed from a conventional

high-temperature oven, they have an extremely

high surface temperature. If they are placed in

the drawer warmer while they are this hot on the

outside, moisture will be pulled from the inside

of the potato and condensation will form on the

outside. Holding results under these conditions

will not be totally satisfactory. Remove potatoes

from the oven and allow the surface temperature

to stabilize before placing them in the controlled

holding atmosphere of the drawer warmer.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 13

Operation

1. Preheat Drawer Warmer at 200°F (93°C) for 30 minutes

before loading hot food.

Push power switch to the On position. The unit will

begin operating at the previous set temperature.

2. Press the Up Arrow or Down Arrow to 200°F (93°C).

Pressing and releasing the Up Arrow or Down Arrow

will change the set point by 1 degree. Pressing and

holding the Up Arrow or Down Arrow will change set

point by 10 degrees. When Arrow is released, a new

set point temperature is set. The set temperature will

appear in the Digital Display and the Heat Indicator

Light will illuminate. Press the Temperature Display

button for three seconds at any time to display the

actual inside air temperature.

To toggle between set temperature and actual inside

air temperature:

Factory default is to display set temperature in the

Digital Display. To display actual temperature:

Press and hold the Temperature Display button and the

Up Arrow for 5 seconds. The control will show

ACT

then show the actual temperature.

Repeat to toggle to display Set temperature

SET

Press the Temperature Display button at any time to

display the alternate temperature.

3. When the inside air temperature reaches the desired

holding temperature, the Heat Indicator Light will turn

off.

4. Load the Drawer Warmer with hot food only.

The purpose of the drawer warmer is to maintain hot

food at proper serving temperatures. Only hot food

should be placed in the Drawer Warmer. Before loading

the Drawer Warmer with food, use a food thermometer

to ensure all food products are at an internal

temperature range of 140°F to 160°F (60°C to 71°C). All

food not within the proper temperature range must be

heated to the proper temperature before loading into

the Drawer Warmer.

5. Check to ensure the drawers are securely closed,

and use the Up Arrow or Down Arrow to set the

temperature to 160°F (71°C).

This will not necessarily be the nal setting.

The proper temperature range for the food being

held will depend on the type and quantity of product.

Whether or not the optional drawer vents should be

open or closed will also depend on the type of food

being held. When holding food for prolonged periods,

it is advisable to periodically check the internal

temperature of each item to ensure maintenance

of the proper temperature range. Reset the holding

temperature accordingly.

To toggle between Fahrenheit and Celsius:

The factory default is Fahrenheit. To change to Celsius:

1. Press and hold the Temperature Display button and the

Down Arrow for 5 seconds.

2. The control will show

for 3 seconds to verify

selection and then show the temperature. (Set

temperature or actual temperature, whichever the user

has selected) in ºC.

3. Repeat to toggle to Fahrenheit.

Press the Temperature Display button at any time to

display the alternate temperature.

NOTICE: In the event of a power failure, the control will

retain the ºC or ºF setting selected by the user.

On/Off Power

Switch

Digital

Display

Up/Down

Arrows

Heat

Indicator Light

Temperature

Display

14 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

General Holding Guidelines

Chefs, cooks and other specialized food service personnel

employ varied methods of cooking. Proper holding

temperatures for a specic food product must be based

on the moisture content of the product, product density,

volume, and proper serving temperatures. Safe holding

temperatures must also be correlated with palatability

in determining the length of holding time for a specic

product.

Halo Heat maintains the maximum amount of product

moisture content without the addition of water, water

vapor, or steam. Maintaining maximum natural product

moisture preserves the natural avor of the product and

provides a more genuine taste. In addition to product

moisture retention, the gentle properties of Halo Heat

maintain a consistent temperature throughout the cabinet

without the necessity of a heat distribution fan, thereby

preventing further moisture loss due to evaporation

or dehydration.

In an enclosed holding environment, too much moisture

content is a condition which can be relieved. A product

achieving extremely high temperatures in preparation must

be allowed to decrease in temperature before being placed

in a controlled holding atmosphere. If the product is not

allowed to decrease in temperature, excessive condensation

will form increasing the moisture content on the outside of

the product. To preserve the safety and quality of freshly

cooked foods however, a maximum of 1 to 2 minutes must

be the only time period allowed for the initial heat to be

released from the product.

Most Halo Heat holding equipment is provided with a

thermostat control between 60°F and 200°F (16°C to 93°C).

If the unit is equipped with vents, close the vents for moist

holding and open the vents for crisp holding.

Holding Temperature Range

Meat Fahrenheit Celsius

Beef Roast — Rare 130°F 54°C

Beef Roast — Med/Well Done 155°F 68°C

Beef Brisket 160°F–175°F 71°C–79°C

Corn Beef 160°F–175°F 71°C–79°C

Pastrami 160°F–175°F 71°C–79°C

Prime Rib — Rare 130°F 54°C

Steaks — Broiled/Fried 140°F–160°F 60°C–71°C

Ribs — Beef Or Pork 160°F 71°C

Veal 160°F–175°F 71°C–79°C

Ham 160°F–175°F 71°C–79°C

Pork 160°F–175°F 71°C–79°C

Lamb 160°F–175°F 71°C–79°C

Poultry

Chicken — Fried/Baked 160°F–175°F 71°C–79°C

Duck 160°F–175°F 71°C–79°C

Turkey 160°F–175°F 71°C–79°C

General 160°F–175°F 71°C–79°C

Fish/Seafood

Fish — Baked/Fried 160°F–175°F 71°C–79°C

Lobster 160°F–175°F 71°C–79°C

Shrimp — Fried 160°F–175°F 71°C–79°C

Baked Goods

Breads/Rolls 120°F–140°F 49°C–60°C

Miscellaneous

Casseroles 160°F–175°F 71°C–79°C

Dough — Proofing 80°F–100°F 27°C–38°C

Eggs — Fried 150°F–160°F 66°C–71°C

Frozen Entrees 160°F–175°F 71°C–79°C

Hors d'oeuvres 160°F–180°F 71°C–82°C

Pasta 160°F–180°F 71°C–82°C

Pizza 160°F–180°F 71°C–82°C

Potatoes 180°F 82°C

Plated Meals 140°F–165°F 60°C–74°C

Sauces 140°F–200°F 60°C–93°C

Soup 140°F–200°F 60°C–93°C

Vegetables 160°F–175°F 71°C–79°C

The holding temperatures listed are suggested guidelines

only. All food holding should be based on internal product

temperatures. Always follow local health (hygiene)

regulations for all internal temperature requirements.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 15

Cleaning and Preventative Maintenance

Protecting Stainless Steel Surfaces

It is important to guard against corrosion

in the care of stainless steel

surfaces. Harsh, corrosive,

or inappropriate chemicals

can completely destroy the

protective surface layer of

stainless steel. Abrasive pads,

steel wool, or metal implements

will abrade surfaces causing damage to this protective

coating and will eventually result in areas of corrosion.

Even water, particularly hard water that contains high

to moderate concentrations of chloride, will cause

oxidation and pitting that result in rust and corrosion.

In addition, many acidic foods spilled and le to

remain on metal surfaces are contributing factors that

will corrode surfaces.

Proper cleaning agents, materials, and methods are

vital to maintaining the appearance and life of this

appliance. Spilled foods should be removed and the

area wiped as soon as possible but at the very least,

a minimum of once per day. Always thoroughly

rinse surfaces a er using a cleaning agent and wipe

standing water as quickly as possible a er rinsing.

Cleaning Agents

Use non-abrasive cleaning products designed for

use on stainless steel surfaces. Cleaning agents must

be chloride-free compounds and must not contain

quaternary salts. Never use hydrochloric acid (muriatic

acid) on stainless steel surfaces. Failure to observe

this precaution will void the warranty. Always use

the proper cleaning agent at the manufacturer's

recommended strength. Contact your local cleaning

supplier for productrecommendations.

Cleaning Materials

Cleaning can usually be accomplished with the

proper cleaning agent and a so , clean cloth. When

more aggressive methods are needed, use a non-

abrasive scouring pad on dif cult areas and make

certain to scrub with the visible grain of surface metal

to avoid surface scratches. Never use wire brushes,

metal scouring pads, or scrapers to remove food

residue. Failure to observe this precaution will void

the warranty.

NOTICE

To protect stainless steel surfaces,

completely avoid the use of abrasive

cleaning compounds, chloride based

cleaners, or cleaners containing

quaternary salts. Never use hydrochloric

acid (muriatic acid) on stainless steel.

Never use wire brushes, metal scouring

pads or scrapers.

WARNING

To prevent serious personal injury, death,

or property damage:

The appliance must be cleaned thoroughly

to avoid deposits of grease and or food

residue inside the appliance that may

catch fire. If fat deposits and/or food waste

inside the appliance ignite, shut down

the appliance immediately and keep the

appliance door closed to extinguish the

fire. If further extinguishing is required,

disconnect the appliance from the main

power and use a fire extinguisher (do not

use water to extinguish a grease fire!).

Failure to clean the appliance properly

invalidates the warranty and relieves

Alto-Shaam of all liability.

16 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Cleaning and Preventative Maintenance

Clean the Drawer Warmer Daily

1. Disconnect unit from power source and let cool.

2. Remove, cover or wrap, and refrigerate food.

3. Remove drawer pans and clean separately. The drawer

assembly is completely removable. Remove drawer

from the cabinet and clean to prevent a build-up of

food residue from interfering with the function of the

drawer assembly. Regular cleaning will prolong the life

of these parts.

4. Clean the interior metal surfaces of the warmer with a

damp clean cloth or sponge and any good commercial

detergent.

NOTICE: Never use abrasive cleaning compounds,

chloride-based cleaners, or cleaners

containing quaternary salts. Never use

hydrochloric acid (muriatic acid) on stainless

steel.

5. Spray heavily soiled areas with a water soluble

degreaser and let stand for 10 minutes, then remove

soil with a plastic scouring pad.

6. Wipe control panel, drawer vents, handles, and gaskets

thoroughly since these areas harbor food debris.

7. Rinse surfaces by wiping with sponge and clean warm

water.

8. Remove excess water with sponge and wipe dry with a

clean cloth or air dry. Leave drawers open until interior

is completely dry.

9. Wipe door gaskets and control panel dry with a clean,

so cloth.

10. Wipe interior with a sanitizing solution aer cleaning

and rinsing. This solution must be approved for use on

stainless steel food contact surfaces.

11. To help maintain the protective lm coating on

polished stainless steel, clean the exterior of the

Drawer Warmer with a cleaner recommended for

stainless steel surfaces. Spray the cleaning agent on

a clean cloth and wipe with the grain of the stainless

steel.

Always follow appropriate state or local health (hygiene)

regulations regarding all applicable cleaning and

sanitation requirements for equipment.

WARNING

To prevent serious injury, death, or property

damage, always disconnect the appliance

from the power source before cleaning

orservicing.

WARNING

To prevent serious personal injury, death, or

property damage:

Do not steam clean, hose down or flood the

interior or exterior with water or liquid solution

of any kind. Do not use water jet toclean. Failure

to observe this precaution will void the warranty.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 17

Food Safety

Food  avor and aroma are usually so closely related that it

is dif cult, if not impossible, to separate them. There is also

an important, inseparable relationship between cleanliness

and food  avor. Cleanliness, operating ef ciency, and

appearance of equipment contribute considerably to savory,

appetizing foods.

Most food imparts its own particular aroma and many

foods also absorb existing odors. Unfortunately, during

this absorption there is not a distinction between good and

bad odors. The majority of objectionable  avors and odors

troubling food service operations are caused by bacteria

growth. Sourness, rancidity, mustiness, stale or other

undesireable  avors are usually the result of germ activity.

The easiest way to ensure full, natural food  avor is through

comprehensive cleanliness. This means good control of

both visible soil (dirt) and invisible soil (germs). A thorough

approach to sanitation will provide essential cleanliness. It

will ensure an attractive appearance of equipment, along

with maximum ef ciency and utility. More importantly, a

good sanitation program provides one of the key elements

in the prevention of food-borneillnesses.

A comprehensive sanitation program should focus on the

training of staff in basic sanitation procedures. This includes

personal hygiene, proper handling of raw foods, cooking

to a safe internal product temperature, and the routine

monitoring of internal food temperatures from the time the

food is received through the time the food is served.

A controlled holding environment for prepared foods is just

one of the important factors involved in the prevention of

food-borne illnesses. Temperature monitoring and control

during receiving, storage, preparation, and the service of

foods are of equal importance.

The most accurate method of measuring safe temperatures

of both hot and cold foods is by internal product

temperature. A thermometer is an effective tool for this

purpose, and should be routinely used on all products that

require holding at a speci c temperature.

Internal Food Product Temperatures

Hot Foods

Danger Zone 40°F to 140°F 4°C to 60°C

Critical Zone 70°F to 120°F 21°C to 49°C

Safe Zone 140°F to 165°F 60°C to 74°C

Cold Foods

Danger Zone Above 40°F Above 4°C

Safe Zone 36°F to 40°F 2°C to 4°C

Frozen Foods

Danger Zone Above 32°F Above 0°C

Critical Zone 0°F to 32°F -18°C to 0°C

Safe Zone 0°F or Below -18°C or Below

Hazard Analysis (at) Critical Control Points (HACCP),

is a quality control program of operating procedures to

assure food integrity, quality, and safety. Taking steps

necessary to augment food safety practices is both

cost effective and relatively simple. Additional HACCP

information is available by contacting:

Center for Food Safety and Applied Nutrition

Food and Drug Administration

Phone: 1-888-SAFEFOOD

www.foodsafety.gov

18 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Troubleshooting

WARNING

To prevent serious injury, death, or property

damage, always disconnect the appliance

from the power source before cleaning

orservicing.

This section is provided for the assistance of

qualified and trained service technicians only

and is not intended for use by untrained or

unauthorized service personnel. Failure to

observe this precaution may void the warranty.

This section is provided for the assistance of qualified technicians only and is not intended for use by untrained

or unauthorized service personnel. If your Alto-Shaam

unit is not operating properly, check the following before

calling your Authorized Alto-Shaam Service Agent:

☛ Check main power circuit breaker to the unit and verify that the circuit breaker on the back of the unit is turned

on, if applicable.

Do not attempt to repair or service the unit beyond this point. Contact Alto-Shaam for the nearest authorized

service agent. Repairs made by any other service agents without prior authorization by Alto-Shaam

will

void the warranty on the unit.

Thermostat Calibration

If you suspect the temperature inside the holding

compartment does not match the temperature

indicated on the digital display, follow the instructions

listed below.

1. Ensure the unit voltage matches the power source.

2. Verify the temperature inside the holding

compartment with a quality thermal indicator.

a. With the exception of the wire shelves,

completely empty the holding compartment.

b. Ensure the drawer warmer sensor, located inside

the drawer is completelyclean.

c. Suspend the thermal indicator in the center of the

drawer.

d. Allow the temperature set on the electronic

thermostat to stabilize for a minimum of one

hour before comparing the digital display with

the reading on the thermal indicator.

Do not open the drawer warmer drawer(s) during the

temperature stabilization period.

If the reading on the thermal indicator does not match

the digital display, there may be a problem with the air

sensor. See troubleshooting guide in this manual; or

call the Alto-Shaam Service Department for advice.

How to verify sensor integrity

Place the sensor in ice water. Test with an ohmmeter set

to the ohm scale.

Air sensor 1000 ohms ± 20

If the reading is more than ± 20 ohms, replace sensor.

MN-29742 • Rev 9 • 12/17 • Drawer Warmers 19

Troubleshooting

Code Description Possible Cause s

E-10 Cavity air sensor shorted

Cavity air sensor reading < 5°F (-15°C). Verify sensor integrity.

E-11 Cavity air sensor open

Cavity air sensor reading > 517°F (269°C). Verify sensor integrity.

E-20

Product probe is shorted

Oven will cook in time only

Product probe reading < 5°F (-15°C). Verify sensor integrity.

E-21

Product probe is open

Oven will cook in time only

Product Probe reading > 517°F (269°C). Verify sensor integrity.

E-30 Under temperature

Unit has been more than 25°F (14°C) below set point for longer than 90 minutes.

E-31 Over temperature

Unit has been more than 60°F (33°C) above the maximum set-point for longer than 3

minutes. Holding Cabinets with this error code are more than 145°F (81°C) above the

maximum set-point.

E-32

Safety switch open

(Aux hi-limit switch)

Contact factory.

E-38 Internal software error

Contact factory.

E-39 Sensor error

Contact factory.

E-50 Temp. measurement error

Contact factory.

E-51 Temp. measurement error

Contact factory.

E-60 Real time clock error

Data set to factory default. Ensure that date and time are correct if applicable.

E-61 Real time clock error

Contact factory.

E-64 Clock is not oscillating

Contact factory.

E-70

Configuration connector error

(DIP switch)

Refer to wiring diagram for the particular model and ensure dip switches on the

control match the settings called out on the WD. If the dip switch settings are correct

according to the print replace the control.

E-78 Voltage low

Voltage below 90 VAC on a 125 VAC unit, or below 190 VAC on a 208-240 VAC unit.

Correct voltage.

E-79 Voltage high

Voltage over 135 VAC on a 125 VAC unit, or over 250 VAC on a 208-240 VAC unit.

Correct voltage.

E-80 EEPROM Error

Ensure that all temperatures and times are properly set.

Contact factory if problem persists.

E-81 EEPROM Error

Contact factory.

E-82 EEPROM Error

Contact factory.

E-83 EEPROM Error

Contact factory.

E-85 EEPROM Error

All timers, if previously on, are now off. Possible bad EEPROM.

E-86 EEPROM Error

Stored HACCP memory corrupted. HACCP Address reset to 1. Possible bad EEPROM.

Contact factory if problem persists.

E-87 EEPROM Error

Stored offsets corrupted. Offsets reset to 0. Control may need a recalibration.

Possible bad EEPROM. Contact factory if problem persists.

E-88 EEPROM Error

All timer set-points are reset to 1 minute. Timers, if previously on, are now off.

Possible bad EEPROM.

E-90 Button stuck

A button has been held down for > 60 seconds. Adjust control. Error will reset when

the problem has been resolved.

E-91 Input failure

Contact factory.

E-dS Datakey error

Datakey digital signature incompatible. Cycle power, and install compatible Datakey

if error persists.

E-dT Datakey error

Datakey incompatible with control. Install compatible Datakey.

E-dU Datakey unplugged

Install Datakey and cycle power to control to clear error.

dLto Datalogger has timed out

Cycle power. Contact factory if error persists.

dLSD Micro SD card not plugged in

Plug in SD card and cycle power. Contact factory if error persists.

NOTE: If in doubt, always cycle the power to the control and contact factory if the problem persists.

20 MN-29742 • Rev 9 • 12/17 • Drawer Warmers

Service

1134

Service View - Exterior

Part numbers and drawings are subject to change without notice.

Page is loading ...

Alto-Shaam 500-3DN Installation Operation & Maintenance

Brand: Alto-Shaam

Model: 500-3DN

Category: Food warmers

Type: Installation Operation & Maintenance

This manual is also suitable for

Download PDF

report

Alto-Shaam 500-3DN Installation Operation & Maintenance

This manual is also suitable for

Alto-Shaam 500-3DN Installation Operation & Maintenance

Related papers

Other documents