5019 301 05528
Whirlpool is a registered trademark of Whirlpool USA.
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in
compliance with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in
relation to the water supply pressure and temperature, the load and the type of wash.
Add the detergents as described in the programme
table or in the chapter “Detergents and Additives” in
the booklet.
1. Open the tap.
2. Set the
programme selector
to the desired
programme.
3. Set the
temperature selector
to the desired
temperature.
4.
Special options
can be selected.
5. Check that the door is well closed and turn on the
washing machine by pressing the
“ON/OFF”
button. The indicator lights up, indicating that
the washing machine is on.
“Intensive Rinse” button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
• This option is particularly recommended for the
programme “Synthetics” or “Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain” programme.
CONSUMPTION DATA
Programme
Temperature
Selector
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours:minutes)
Cotton 95 5.0 49 1.70 1:50
Cotton 60 5.0 44 0.95 2:20
Cotton 40 5.0 44 0.55 1:50
Synthetics 60 2.5 55 0.80 1:25
Synthetics 40 2.5 50 0.60 0:50
Delicates 40 1.5 50 0.50 0:45
Wool 40 1.0 50 0.50 0:40
Silk 30 1.0 37 0.40 0:40
ADD DETERGENTS, CLOSE THE DOOR AND SELECT
THE PROGRAMME
SELECT ANY DESIRED OPTION
“Spin Speed Reduction” button
• Reduces the predetermined automatic
maximum spin speed.
In some programmes the maximum final spin
speed is limited to go easy on your laundry
items. Selection of a higher spin speed is not
possible.
To reselect a programme when a cycle has already
begun:
1. Switch off the appliance by pressing the “
ON/
OFF
” button.
2. Select the new programme.
3. Start the programme by pressing the “
ON/OFF
”
button.
1. At the end of the programme the programme
selector moves to the stop position.
2. To unload the machine wait for the door to
unlock (about 1 minute).
3. Switch off the appliance, open the door and
take out the laundry.
4. Close the tap and leave the door ajar to allow
the drum to dry out.
•
WATER LEVEL
It may not be visible as the cycle is optimised
for a minimum water consumption without
compromising washing results.
•
SPIN SPEED CONTROL
Spin speed may be reduced automatically or
may even be excluded in the case of small
loads with highly absorbent garments (e.g.
bathrobes, bathmat).
This control avoids cloth and machine damage
and excessive vibrations and consequent
noise produced by the machine due to load
unbalance: by selecting high spin speeds the
noise level increases.
•
MOTOR NOISE
The running noises of the new, electronically-
controlled motor are not the same as the ones
you are used to from your old appliance. Don’t
be surprised - modern technology has a
modern sound.
•
CLEANING THE FILTER
To ensure an impeccable function of the
pump, check the filter regular and clean it if
necessary.
PROGRAMME CHANGE
PROGRAMME END
NOTES AND INDICATIONS FOR USE
3gb05528.fm Page 2 Friday, September 19, 2003 11:21 AM
Black process 45.0° 100.0 LPI