Amino JSTV-i User manual

Category
Signal cables
Type
User manual
For Wi-Fi setting, please refer “How to connect Wi-Fi” on page 3.
SIGN IN (Please refer page 2 for remote control
operation)
Enter your JSTV-i username with numeric / alphabet button.
Move down to the password field with arrow button.
Press OK button and the colour of the password field will change from
blue to orange. Now it’s ready to enter your password.
Select “SIGN IN” with arrow button and press OK button.
To switch off the STB, please make sure that it’s selecting “SING IN”
and then switch off with power button on the remote control. If
Username or Password field is active, you are not able to switch off
the STB with remote control.
SELECT CHANNEL
Channel selection will be displayed on the TV monitor. Select a
channel with right / left allow and press OK button.
Or you can select with numeric button. 1 is for JSTV1, and 2 is for
JSTV2.
You will be able to change the channel while you are watching by
pressing the numeric button.
MENU LANGUAGE
You can change your language preference by colour buttons on the
remote control at anytime.
Red = Japanese Green = English
HDMI Cable : Connect to TV with enclosed HDMI cable
Wi-Fi Dongle : Connect Wi-Fi Dongle
The Dongle is only provided for a customer who requested on an order form.
LAN Cable : Connect with router
You need to get an LAN Cable long enough to connect your router and STB.
Power Cable : Please connect power cable at the end.
Do not press down the RESET button when you connect the power cable.
It will reset the STB and you won’t be able to watch JSTV.
The RESET button located right next to the power cable connection.
Please always use the power cable supplied. Do not use any
power cable from different device even it look same. This cause
the STB to be damaged and cannot be repaired.
AMINO STB User Guide
You can enjoy JSTV-i on TV when you connect AMINO STB to your
TV with HDMI cable. To achieve stable viewing, we recommend
wired connection (with a LAN cable) rather than use the Wi-Fi
connection.
CABLE CONNECTION
About Sign in / Sign out
Username and password will be saved on AMINO STB. So you do not
need to enter each time when you switch it on. For security reason,
you may asked to enter the username and password randomly.
You can sign out with Blue button on remote control on the channel
selection page.
While you are watching, you can back to the channel selection page
with stop button () on remote control.
After watching JSTV continuously 5 hours, a message appear on TV
monitor asking if you are still watching JSTV. Please press OK button
on remote control to continue watching.
Set up for JSTV-i
1
Remote Control Operation Guide
HOW TO INPUT ALPHABET
When you press down and hold the Alphabet Button, the character on the button will
appear one by one. Release the button when you see the required number or letter to
enter.
For example, if you want to enter “c”, press down number 2. You will see character
changes as 2, a, b, c. When you see “c”, release the button.
Press P<P button which placed above the numeric button to delete a letter you entered.
ENTER CAPITAL LETTER
When you press down and hold the 0 button, character changes as 0, a, 0, A. When “A”
appears, release the button and you will be able to enter the capital letter.
To switch back to small letter, press down and hold 0 button and choose “a”.
PAUSE AND RESUME VIEWING
Stop Viewing
Press standby button to turn off the STB or press the Stop button () to back to the
channel selection page.
Restart Viewing
Press standby button to turn on the STB or from channel selection page choose desire
channel.
Numeric /
Alphabet Button
JAPANESE
(Red
ENGLISH
(Green)
Standby
Sign out
(Blue)
Delete
Switch
Upper and
Lower Case
Arrow and
OK Button
Trouble Shooting
Switch menu language anytime by colour button.
Red = Japanese Green = English
Unexpected server error
It might caused by unstable internet connection. Please reboot the STB by removing
power cable. Also reboot your internet router.
Concurrent Stream Check
If you are with in the maximum number of concurrent devices allowed, switch off the
STB and wait for 5 minutes and try again.
JSTV Customer Service
+44-(0)20-7426-7330
Monday to Friday 9:00-16:00(UK) 10:00-17:00(CET)
customerservice@jstv.co.uk
You must point the remote at the Amino STB when
you operate.
2
Please check the internet router etc if it take long time to
scan.
Select your wifi network and press OK button.
Connect the Wifi dongle to AMINO before power on. Press
OK button when you see this message
Select “Scan/Connect WAPs” and press OK button
How to setup Wifi (You can change the Wifi setting by MENU button on remote.
3
Enter your Wi-Fi password and move to “Accept” and then
press OK button.
After entering the Wi-Fi password, the screen back to “Wireless
Configuration”. Select “EXIT”. If you entered a wrong Wi-Fi
password, choose “Forget WAPand try again.
Select “Connect using WAP password” Select “WPA2-PSK-AES” if there are more than 1 options. If it doesn’t
work, try the others.
4
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Amino JSTV-i User manual

Category
Signal cables
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI