PROGRAMME START
Open the tap and press the “Start/Pause” button. The
indication lamp next to the “Start/Pause” button lights
up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain.
When the laundry load is detected or the programme
duration is updated, the display shows an animation.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the
lamp lights to show the the door can be opened.
As long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel (Reset)
a running programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”: no or not sufficient inlet water.
”Service”: failure or malfunction of an electrical
component.
”Clean pump”: waste water is not pumped out.
Spin speed indication blinks : unbalance during
spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display
shows “End”. After about a quarter of an hour, the
washing machine will switch off completely to save
energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, any options and
another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset” button cancels a programme before the
end.
• Press and hold the “Reset” button for a few
seconds. Any existing water is drained out. It may
last some time until the door can be opened.
“Rapid” button
• Enables quicker washing by shortening the
programme duration.
• Recommendable for only lightly soiled laundry.
• Not selectable for Cotton 95°C.
“Clean+” button
• Choose this option if you use an in-wash additive
for stain removal (powder, for example “Vanish”) - it
will optimize the additive’s efficiency to get better
wash performance and stain removal.
• Use with the maximum load.
• Add an appropriate amount of in-wash additive
for stain removal (powder) to the main wash
chamber, together with your detergent (only use
powder detergent with this option). Respect the
manufacturer’s dosing instructions.
• May prolong the programme by up to 15 minutes
• Appropriate for use of stain removers and bleaches
on oxygen basis. Chlorine or perborate bleaches
must not be used!
“Prewash” button
• Adds a prewash cycle to the wash programme
selected; prolongs the programme by about a
quarter of an hour.
• Recommended for heavily soiled laundry (e.g. with
sand or granular dirt).
• Do not use liquid detergent for the main wash when
activating the “Prewash” option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
LOAD LAUNDRY, ADD DETERGENTS
AND SELECT THE PROGRAMME
Load the laundry, close the door and add detergents
as indicated on the front page and as described in the
chapter “Detergent and Additives” in your Instructions
for Use.Turn the programme selector to the desired
programme and temperature. The display shows the
programme duration. The indication lamp next to the
“Start/Pause” button blinks.
If you do not start the programme soon after having
made your choice, the washing machine will switch
off automatically after about a quarter of an hour.
Switch on the washing machine again by turning
the programme selector back to “O” and then to the
desired programme.
SELECT ANY DESIRED OPTION
Push the button of any option desired - the respective
indication lamp lights up. If the combination of
programme and additional option(s) is not possible,
the indication lights switch off automatically.
“Cold wash” button
• Saves energy used for water heating while
maintaining good wash result.
• Recommendable for lightly soiled laundry without
stains.
• Make sure that your detergent is suitable for cold
wash temperatures (15 or 20 °C).
• Mainly selectable on the lowest temperature step of
the programmes.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Easy ironing” button
• Reduces creasing by an increased water quantity
and a very gentle spin. “Rinse hold” button
• The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• The programme stops to “Rinse hold” at the time
the “Rinse hold” lights in the preogramme sequence
indication is on. The “Start/Pause” indicator blinks.
“Rinse hold” button
• The laundry remains in the last rinse water without
pregressing to the final spin cycle to avoid creasing
and prevent colours from changing.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
• The programme stops to “Rinse hold” at the time
the “Rinse hold” lights in the preogramme sequence
indication is on. The “Start/Pause” indicator blinks.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for
the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector to the “Drain” programme and
press the “Start/Pause” button
“Spin” button
• Every programme has a predefined spin speed.
• Press the button to set different spin speed.
• If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
START DELAY
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating “Start delay” option.
• Select programme, temperature and options.
• Press the “Start delay” button to select the desired
delay time up to 23 hours.
• Press the “Start/Pause” button. On the display, the
start delay symbol and the dot between hours and
minutes blink. The countdown of the delay time
begins.
• The time delay indication disappears when
the programme starts and it is replaced by the
remaining programme time.
• Once having pressed the “Start/Pause” button, the
delay time can be reduced by pressing again the
“Start delay” button.
To cancel the “Start delay”
...before you press the “Start/Pause” button:
• Turn the programme selector to another position or
press the “Reset” button.
...after having pressed the “Start/Pause” button:
• Press the “Start/Pause” button - the start delay
time disappears from the time display.
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
%
without “Rapid” with “Rapid”
Cotton 95 8.0 82** 2.50 2:30 -
59Cotton 60 8.0 59 1.36 2:20 1:35
Cotton 40 8.0 75 1.00 2:20 1:15
Jeans 40 4.0 52 0.50 1:30 1:10
Synthetics 60 3.0 48** 1.05 2:05 1:12
40
Synthetics 40 3.0 44 0.60 1:50 0:57
Delicates 40 1.5 60 0.65 0:50 -
Delicates 30 1.5 60 0.40 0:46 -
Daily load 40 4.0 48 0.50 1:00 - 59
Quick wash 30 3.0 48 0.25 0:30 -
Wool/ Handwash 40 1.0 45 0.55 0:40 -
Cotton
60°
*
60 8.0 54 0.98 4:00 -
53
Cotton
60°
*
60 4.0 40 0.75 3:15 *** -
Cotton
40°
*
40 4.0 45 0.62 3:00 *** -
CONSUMPTION DATA
Power consumption in off-mode 0.16 W / in left-on mode 0.16 W
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the energy
consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default setting of the
programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
