AUTOTECH 10.715.009K Installation guide

AUTOTECH
Brand
AUTOTECH
Model
10.715.009K
Type
Installation guide

This manual is also suitable for

AUTOTECH 10.715.009K is a short shift kit designed for 5-speed Rabbit, Scirocco, and Jetta 1 vehicles. It offers adjustable shift reduction, with a choice between a 50% or 30% reduction in shift throw. The kit includes a new relay shaft, selector lever, selector shaft, and bushings. Installation requires basic tools and can be completed by following the instructions provided in the manual. The kit is designed to improve shifting performance and reduce effort, while maintaining a high level of precision and durability.

AUTOTECH 10.715.009K is a short shift kit designed for 5-speed Rabbit, Scirocco, and Jetta 1 vehicles. It offers adjustable shift reduction, with a choice between a 50% or 30% reduction in shift throw. The kit includes a new relay shaft, selector lever, selector shaft, and bushings. Installation requires basic tools and can be completed by following the instructions provided in the manual. The kit is designed to improve shifting performance and reduce effort, while maintaining a high level of precision and durability.

Installation Instructions
Part Number: 10.715.010K
Description: Short Shift Kit for 5 speed Rabbit, Scirocco,& Jetta 1
Tools Required :
Two ramps or jackstands
Metric wrenches, 13 to 17mm
Screwdriver
Ruller or tape measure
Moly grease
Notes:
This Short Shift Kit is selectable for shift reduction. The selector shaft included in the kit has two rod locating holes. The
upper hole will give a 50 percent reduction in shift throw, while the lower hole provides for a 30 percent reduction. The 50
percent reduction will naturally require a slightly greater effort in shifting.
Procedure:
1. Place the front of the car on ramps or jack stands so that you may access the shifter assembly from below.
2. Remove the linkage selector rods by carefully unclipping the plastic hooks on the snap balls with a screwdriver.
3. Next, remove the standard relay shaft, selector lever, and selector shaft from the vehicle using the appropriate wrenches.
When doing so, note the location of any bushings you remove so that they may be properly replaced when you are
reassembling the linkage.
4. Now fit the new linkage pieces into place using any new bushings that came with the short shift kit.
5. Reattach the linkage selector rods making sure to lubricate the ball ends with moly grease.
6. The only adjustment that may be required after the shift kit is installed is to the shift rod. The shift rod connects the
linkage network to the shift lever itself. The adjustment bolt is accessed from underneath the car where the shift lever and
the shift rod connect. A weather seal mu8st first be removed.
7. Depending on your vehicle, the weather seal is either a rubber boot that must be detached from the housing and pulled
forward along the shift rod, or simply a round plastic cover that more or less looks like a coffee can lid.
8. From the neutral position, move the shift lever so that it is aligned with the 3rd and 4th gear gate. While the lever is in this
position, dimension “A” at the top finger should be set to 15mm(see illustration)
Parts List:
One Relay shaft
One Selector lever
One Selector shaft
One Set of bushings
  • Page 1 1
  • Page 2 2

AUTOTECH 10.715.009K Installation guide

AUTOTECH
Brand
AUTOTECH
Model
10.715.009K
Type
Installation guide
This manual is also suitable for

AUTOTECH 10.715.009K is a short shift kit designed for 5-speed Rabbit, Scirocco, and Jetta 1 vehicles. It offers adjustable shift reduction, with a choice between a 50% or 30% reduction in shift throw. The kit includes a new relay shaft, selector lever, selector shaft, and bushings. Installation requires basic tools and can be completed by following the instructions provided in the manual. The kit is designed to improve shifting performance and reduce effort, while maintaining a high level of precision and durability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents