Declaration of Conformity
Hereby, Amino Communications Ltd. declares that the radio equipment type
IP Digital set-top box
is in compliance with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the
following internet address: https://www.aminocom.com/support
Amigo 7X
Quick Start Guide
Open the box carefully. The following items should be inside:
4K Android TV player HDMI cable
Power adapter IR remote control
Important!
Please contact your local distributor immediately if, when opening the box, you find any
damage and/or loss of any of the items.
This manual is for reference only and may differ from the actual product appearance.
Please follow the product if they differ.
Product checklist
380003188 v1
Federal Communication Commission (FCC) & Industry Canada (IC)Radiation Exposure Statement
When using the product, maintain a distance of 20cm from the body to ensure compliance with RF
exposure requirements.
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications or changes to this equipment. Such modifications or changes could void the user’s authority
to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
IC Notice:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with Canada Industry licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference. and (2) this device must accept any
interference. Including interference that may cause undesired operation of the device.
CAN ICES-3 (B)
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage; (2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NMB-3 (B)
FCC ID:XVG50-0112-RT-22
IC ID: 6800A-500112RT22
For Canada, 5150~5250 MHz are restricted to indoor use only.
Operating temperature: 5 °C to 35 °C (40 °F to 95 °F)
Frequency bands and maximum powers:
WLAN Bluetooth RF4CE
2.4 GHz: EIRP < 20 dBm
5.18~5.24 GHz: EIRP < 23 dBm
5.26~5.32 GHz: EIRP < 23 dBm
5.50~5.70 GHz: EIRP < 23 dBm
BT-EDR: EIRP < 4 dBm
BT-LE: EIRP < 2 dBm
EIRP < 1.5 dBm
Operating information
Panel description
1. Display (power LED) and IR receiver
2. DC power input.
3. Analogue A/V output (adapter cable available).
4. HDMI port.
5. Ethernet port.
6. S/PDIF optical output. Connect an S/PDIF optical digital cable between this output and an
audio amplifier.
7. USB port. Use for external storage media such as a hard drive or USB flash drive.
You can also update software and program lists using this connection.
Note: your external storage media must be formatted with FAT32.
Hardware setup procedure
Preparation for installation:
Unpack the box and check the supplied items
Prepare the television set and power supply jack
Place the unit beside the TV set
•
•
•
Caution:
a) Unplug the unit before making any physical connection to other equipment.
Also ensure that AC power is disconnected from other equipment.
b) The connections of all video/audio cables supplied are colour-coded to the jacks of
related equipment. When connecting make sure that the colours are matched.
c) Proper physical connections are important - ensure you insert the plug completely.
The power adapter must be connected last.
Ensure that your TV is set to the correct input channel depending on your connection
type, e.g. AV1, AV2, HDMI.
Use the TV remote control to select the TV input channel connected to the box.
Refer to your TV user guide or technical helpline if you are unable to select the input
channel.
Installation diagram
System requirements and setup environment
System requirements Setup environmemnt
TV set with video and audio
Reliable and safe internet connection
•
•
Set up the system following the procedures
described in this manual
•
Place the unit away from any heat source•
Do not put the unit in a dirty or humid place•
!
!
/