ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC)
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61200780L1-13A, August 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
Connecting to the ATLAS 830
Connecting a VT100 terminal (or VT100 terminal emulator) to the C
RAFT
interface (on the front panel of the unit) or the A
DMIN
interface (on the rear panel
of the unit) allows access to the terminal menus and management features of
the ATLAS 830.
Perform Steps Below in the Order Listed:
1. Configure a VT100 terminal (or terminal emulation software) with the
following settings:
If the terminal has a parallel setting, disable it and use serial.
2. Connect the DB-9 male end of the data cable into the ATLAS 830 C
RAFT
or
A
DMIN
port. Make the connection to the VT100 terminal as appropriate for
your connection.
3. Initiate a terminal session and the L
OGIN
screen displays. The default
password is password. (Passwords in the ATLAS 830 are case sensitive.)
Data Rate: 9600 baud Stop Bits: 1
Data Bits: 8 Flow Control: None
Parity Bits: None
ATLAS 830
1
2
3
4
5
6
7
8
STATUS
ONLINE
TEST
MODULES
1
2
NE T W O RK
TEST
ERROR
ALARM
OK
TEST
ERROR
ALARM
OK
PO WER
ETHERNET
REMOTE
SYSTEM
CRAFT
ACO
Network Ports LEDs
Option Module LEDs
Craft Interface
Controller LEDs
ACO Switch
Craft Pinout
System Status LEDs
The System Status LEDs display the status of the power supply, controller, and
other system parameters for the ATLAS 830. For a more detailed discussion of
the front panel LEDs, refer to Section 2, Engineering Guidelines, of the ATLAS
830 System Manual.
PIN NAME DESCRIPTION
1, 4, 6-9 N/A Not Connected
2 RD Receive Data (output)
3 TD Transmit Data (input)
5 SG Signal Ground
LED Description
Power Indicates the status of the power supply
System Indicates the status of the unit controller and other system parameters.
Ethernet Indicates the status of the ethernet port.
Remote Indicates whether a user (Telnet or VT100) is logged in to the unit.
Reviewing the Front Panel
ATLAS 830 P/N 1200780L1 (AC)/1200781L1 (DC)
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61200780L1-13A, August 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
SEE MANUAL BEFORE
REMOVING POWER SUPPLY
OFF
ON
CAUTION: FOR CONTINUED PROTECTION
AGAINST RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE AND RATING
OF FUSE.
12A/125V
+
-
48 VDC, 6A
USE COPPER
CONDUCTORS ONLY
Network T1/PRI Ports
Optional DC
Power Supply
P/N 1200229L1
T1/PRI Monitor Jacks
Alarm Relay Connection
Admin Interface
Option Module Slots
Power Supply Slot
Reviewing the Rear Panel Design
Admin Pinout
10/100BaseT Ethernet Pinout
PIN NAME DESCRIPTION
1 DCD Data Carrier Detect (output)
2 RD Receive Data (output)
3 TD Transmit Data (input)
4 DTR Data Terminal Ready (input)
5 SG Signal Ground
6 DSR Data Set Ready (output) -- not connected
7 RTS Request to Send (input)
8 CTS Clear to Send (output)
9 RI Ring Indicate (output) -- not connected
PIN NAME DESCRIPTION
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4,5 — Unused
6 RX2 Receive Negative
7, 8 — Unused
Alarm Relay Connection Pinout
DC Power Supply Connection
(Optional P/N 1200229L1)
PIN NAME DESCRIPTION
1 Normaly Closed (NC) Opens when a selected alarm condition is present.
2 Normally Open (NO) Closes when a selected alarm condition is present.
3 Common (COM) Common connection between external circuitry
and NC or NO terminal.
4 Chassis Ground (GND)
PIN NAME DESCRIPTION
1 + Ground (GND)
2--48VDC
-
1
-
2
ADTRAN Atlas 830 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ADTRAN T1 User manual
-
ADTRAN ATLAS 550 Quick start guide
-
-
-
-
-
-
-
-