Bennett Marine AP000A1HA Quick start guide

Brand: Bennett Marine

Model: AP000A1HA

Type: Quick start guide

Bennett Marine AP000A1HA is an advanced automatic trim tab control system designed to enhance the performance and efficiency of your boat. With its user-friendly interface and powerful features, the AP000A1HA offers a range of benefits to make your boating experience more enjoyable and hassle-free:

Automatic Trim Adjustment: The system automatically adjusts the trim tabs based on boat speed, load, and sea conditions, ensuring optimal boat attitude and performance.
Improved Fuel Efficiency: By optimizing the trim of your boat, the AP000A1HA can help reduce fuel consumption and increase your cruising range.

Automatic Trim Adjustment: The system automatically adjusts the trim tabs based on boat speed, load, and sea conditions, ensuring optimal boat attitude and performance.
Improved Fuel Efficiency: By optimizing the trim of your boat, the AP000A1HA can help reduce fuel consumption and increase your cruising range.

Quickstart Guide

Auto Trim

Activity Indication

LEDs alert you

to the automatic

movements of the

tabs in real time.

You can see exactly

what adjustments

AutoTrim Pro

is doing for you.

Tabs “All Up” or “All Down” (Semi-automatic)

Fully retract or deploy tabs with a single touch

in manual mode whenever needed.

Adjust LEDs:

Dim (Moon) or Brighten (Sun)

Tab Position

Indication

Shows the current

position of the

trim tabs

in manual and

automatic mode.

Favorite Settings

(Automatic)

Store and

activate two

“Favorite” pitch

and roll settings

to automatically

achieve your

preferred cruising

attitude.

Trim Tab Controls

(Manual)

Override

automatic mode

with a touch to

take full manual

command of the

trim tabs.

Need help? We’re here for you.

Mon.-Fri. 8 AM - 5 PM (EST) ATP65 r081017

Component Installation (Manual pg. 7)

Sensor Check (Manual pg. 6)

One-time Calibration & Set-up (Manual pg. 20)

Refer to your manual

for detailed information

Installing AutoTrim Pro consists of two components–the Helm Display

and the Control Unit. However, operation of the AutoTrim Pro assumes the

presence of a complete trim tab system (Tabs, actuators and a pump).

For help ordering trim tab system components, give us a call.

AutoTrim Pro is equipped with trim tab position LED indicators.

For this feature to work, actuator sensors must be present. Once installed,

the presence of sensors will be indicated with the 2 upper yellow LEDs on the

Helm Display, and 2 green LEDs on the Control Unit continuously illuminated.

The Red LEDs should be ﬂashing to indicate the system needs calibration.

Press and hold the Sun + Moon buttons (See below) for 3 seconds until the

lower yellow LEDs begin to ﬂash. Press both DN buttons, then release when

the tabs are fully down. Wait until the upper yellow LEDs ﬂash. Press and hold

both BOW UP buttons until the tabs are fully up. Release, and the four yellow

LEDs in the corners should be continuously on. You’re Calibrated!

See the reverse side of this card for the one-time system set-up.

HYDRAULIC

Installation

Control/Display Overview

ATP Quickstart Guide-Hydraulic r081017.indd 1 8/11/17 5:04 PM

(866) 894-1626

Need help? We’re here for you.

Mon.-Fri. 8 AM - 5 PM (EST)

HYDRAULIC (SIDE 2)

Orientation of Rest State

The FAV1 and FAV2 blue LEDs should be ﬂashing as an indication

that the system is ready to be oriented. With the boat at rest in

the water, press and hold the Sun + All UP buttons for at least 5

seconds. Once released, all four corner LEDs will ﬂash indicating

that a setting has been made.

Angle Set-up for Planing Mode (Manual pg. 25)

In relatively calm water, put the trim tabs to a half-down position

and run the boat at it’s fastest safe speed. Once at a steady pitch

and speed press and hold the Moon + FAV2 buttons for at least

5 seconds. Once released, all four corner LEDs will ﬂash indicating

that a setting has been made. NOTE: The boat will temporarily run

in a “bow down” condition during the “Planing Angle Set-up” step.

Angle Set-up for Idle Mode (Manual pg. 24)

In relatively calm water with the trim tabs fully retracted (Up),

run the vessel at a typical “No Wake Zone” idle speed. At a

steady running attitude, press and hold the Moon + FAV1

buttons for at least 5 seconds. Once released, all four corner

LEDs will ﬂash indicating that a setting has been made.

Orientation of Acceleration State (Manual pg. 23)

Press and hold the Sun + FAV1 buttons for at least 5 seconds. All

four corner LEDs will ﬂash indicating readiness. Quickly throttle up

to speed in a straight line for at least 10 seconds. Once the system

has sensed an acceleration, all four corner LEDs will ﬂash again

indicating that a setting has been made, and the FAV1 and FAV2

LEDs will stop ﬂashing, indicating that orientation is complete.

Storing and Activating Favorite Settings (Manual pg. 37)

To use AutoTrim Pro in AUTO mode, you ﬁrst need to set a

“Favorite” setting. Manually adjust the trim tabs, throttle, and engine

trim to attain your desired pitch and roll attitude. Next, press and hold

the FAV1 OR FAV2 button for 5 seconds (or more). Once released,

the blue LED will illuminate, and the system will immediately

go into AUTO mode. Pressing any other button on the control

will deactivate AUTO mode putting you back in manual control.

Reactivate the FAV setting any time with a quick button tap.

Favorite settings can be updated any time by repeating step 5.

Or FAV2

ORIENTATION

ANGLE SET-UP

One-time System Set-up

(Manual pg. 23)

Watch the system set-up video

BennettTrimTabs.com/ATPSet-up

ATP Quickstart Guide-Hydraulic r081017.indd 2 8/11/17 5:04 PM

(866) 894-1626

Bennett Marine AP000A1HA Quick start guide

Brand: Bennett Marine

Model: AP000A1HA

Type: Quick start guide

Automatic Trim Adjustment: The system automatically adjusts the trim tabs based on boat speed, load, and sea conditions, ensuring optimal boat attitude and performance.
Improved Fuel Efficiency: By optimizing the trim of your boat, the AP000A1HA can help reduce fuel consumption and increase your cruising range.

Download PDF

report

Bennett Marine AP000A1HA Quick start guide

Bennett Marine AP000A1HA Quick start guide

Related papers

Other documents