WALK WAY WITH CLASSIC 6003
Required tools
(not included)
WARNING
PN: 110-107
Do not dive or jump from the step or ladder.
Use BATTERY operated tools to avoid electric shocks.
Install step on flat surface, following the manufacturers'
instructions .
Remove step from pool during freezing climate season.
Manufacturer cannot be held responsible for injuries caused
by abusive use of product.
Ask your city about specific regulations that apply to your
above-ground pool and ladder.
Sand
15 lbs
(Not included)
Sand
Contents of Accessory box
x2
x2
x4
x4
105-012
105-005
x4 x4
115-010
115-015 (1 1/2 in.)
x8
x18
115-014 (3/4 in.)
115-018 (2 1/2 in.)
x2
SCREW BAG 140-061
x2
Walk Way Step
PG. 1
x1
Contents of ladder box SKU # 6003
A weather resistant padlock is
recommended. Maximum functional
width is 1/4 inch.
Security strap
SCREW BAG 140-058
CABLE LOCK
***PADLOCK REQUIRED
x2
x2
x2
x2
x2
x2
105-012
105-005
x2 x2
115-014 (3/4 in.)
x18
115-018 (2 1/2 in.)
x2
125-035
x4
A
1) Flip the Walk Way
so that the steps
are directly facing
the ground.
2) Place the
support tube,
one side at a time,
in the pockets located
in the bottom lip.
3) Flip the step back
to its original usage
position.
4) Secure the support
tube to the step with
the screws provided.
115-014 (3/4 IN.)
x2
REV: 22/02/11
x1
B
PN: 110-107
MANUFACTURER
WARRANTY
1 year on the step.
1 year on the hardware.
2) Insert the platform,
2 small handrails, and
2 large handrails over
the 2 rear posts.
Do not secure.
x4
105-012
105-005
x4 x4
115-010
PG. 2
1) Insert the four posts into
the step. Secure the posts
in place with the bolts,
washers and nuts
provided. x8
115-014 (3/4 in.)
To prevent a
pool liner
puncture, keep
a minimum of
1"inch gap
between the
pool liner and
the rear underside
of the step.
WARNING
1) Insert the entire step into the pool.
Becareful not to damage the pool liner.
MINIMUM OF 1"
E2) Slide the platform to the height of the top seat.
3) Insert the 4 post covers
and secure the large
handrails to the posts
with the screws provided.
Do not secure
platform.
C1) Fill the ballast with sand till you
reach the top brim.
D
REV: 22/02/11
x4
1) Snap the suction cups into the 4 holes under the step.
Push while twisting, till the upper cup mushroom
has cleared the wall thickness of the step.
Sand
2) Secure the
counterweight
cover with the
screws provided.
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
F
PN: 110-107
MANUFACTURER
WARRANTY
1 year on the step.
1 year on the hardware. PG. 3
I
G
H
REV: 22/02/11
A
x2
115-014 (3/4 IN.)
4) Secure the ladder base to the posts with the screws provided.
3) Slide the 2 posts through the platform and handrails.
SWING THE LADDER UP AND
LOCK IN PLACE WHEN THE
POOL IS NOT IN USE TO
PREVENT DROWNING
AND UNAUTHORIZED ENTRY.
WARNING
CABLE LOCK
***PADLOCK
REQUIRED
x1
Security strap
x2
1) Once the step is in the pool, secure theplatform to the
top seat (see illustration) using the two straps provided.
115-018 (2 1/2 in.)
x2
OPTIONAL:
Once the pool step has been completely assembled and secured to
the pool, attach the 2 screws supplied through the platform to the top
seat of your pool to provide a more rigid assembly.
x2
105-012
105-005
x2 x2
125-035
115-014 (3/4 in.)
x16
1) Secure the small handrails and platform to the
posts with the screws provided.
2) Secure the ladder to the pivot blocks
using the bolts, washers and nuts provided.
48''&52''
54''
align
2) Slide the pivot blocks onto the posts and line up with
the traced marks. Do NOT Secure yet.
1) Trace a line on each post at 39 inches from the ground for
48'' & 52'' Pools. If you have a 54'' pool trace a line at 40.5''
from the ground.
3) Secure the pivot blocks (FIRST ASSEMBLED TO THE LADDER),
to the posts with the screws provided. Make sure the pivots blocks
are lined up with the marks traced earlier.
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5
/
