voda VST21 Storm Wall Mounted Basin Mixer User manual

STORM

Wall Mounted Basin Mixer

VST21

Voda Plumbingware Limited | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz

Congratulations on your purchase of this high quality product from Voda Plumbingware.

Please read the following before installation and retain (along with your receipt) for future reference.

TECHNICAL SPECIFICATIONS

Suitable for All Pressures

Minimum Pressure = 35kPa

Maximum operating Pressure = 500kPa* (As per NZ Building Code AS/NZ 3500.1)

Maximum operating Temperature = 65 deg. Celsius

For domestic use only.

CONFIGURATION

Mains Pressure systems Install mixer and spout as supplied.

Unequal Low systems Insert Green Non-Return valve into Hot inlet port (marked with H), and Yellow Flow

Restrictor into Cold inlet port (marked with C). Note direction of flow arrows on

side of inserts, install with black O-ring to outside on yellow insert, and white o-ring to

outside on green insert. Change the aerator to the Low Pressure flow straightener supplied

in the box.

Equal Low systems Install mixer as supplied. Change the aerator to the Low Pressure flow straightener

supplied in the box.

INSTALLATION

*FOR PRESSURES EXCEEDING 500kPa INSTALL A PRESSURE REDUCING VALVE. THOROUGHLY FLUSH ALL

PIPES TO ELIMINATE ANY REMAINING DIRT AND RESIDUE, AND INSTALL INLINE FILTERS. FAILURE TO DO SO

MAY VOID THE WARRANTY.

• SEE DIAGRAM OVERLEAF.

• Flush all water lines to remove any foreign materials so it does not interfere with the flow regulated aerator or

damage the ceramic cartridge.

• Make sure that the body recess including wall lining thickness allows wingback to fit flush with wall lining

(approx 37mm).

• Note the protrusions at the back of the body to ensure a perpendicular mounting once screwed into place.

• Note when installing breech pipe the dierent tail lengths. The longer tail length should be fitted into the

wingback, with shorter tail into mixer body.

• The three piece mixer-wingback-breech pipe design allows for dierent spout/mixer configurations to suit

dierent bathroom designs. The mixer can be installed on the le or right hand side of the spout, and with the

mixer handle either pointing up or down.

• Copper olives and brass nuts are supplied, ensure the use of adequate hemp and graphite, or PTFE tape to

ensure a water tight fit as per good plumbing practice.

• Aer screwing spout to wingback, spout can be adjusted to final positioning by loosening small grub screw

underneath spout and aligning.

• Turn on mains supply.

• Check for leaks.

Plumbers Note: Do not pressure test this mixer under static pressure.

WARRANTY

PLEASE CALL US BEFORE REMOVING TAPWARE OR UNDERTAKING ANY REPAIR WORK.

Please refer to our website for full warranty information: www.vodaplumbingware.co.nz/warranty

In the unlikely event that this product fails during its warranty period, phone our Customer Service team

immediately on 0508 367 366 – as unauthorised removal of the product may void the warranty.

CARE AND MAINTENANCE

SHOULD NOT BE CLEANED WITH ACIDIC, CAUSTIC/ALKALINE, ABRASIVE OR CITRIC CLEANERS.

A so, damp cloth is recommended for cleaning. Mild soap solutions can also be used on occasion.

ATTACH PROOF OF PURCHASE HERE

Voda Plumbingware Limited | Freephone: 0508 367 366 | 5 Hewlett Street, Port Whangarei 0110 | vodaplumbingware.co.nz

PROUD PARTNER AND SUPPORTER OF MASTER PLUMBERS, GASFITTERS AND DRAINLAYERS

Min 45mm

Max 60mm

**IMPORTANT:

This mixer and spout are

fitted with 80mm faceplates.

Maximum hole dimension in

finished wall lining should not

exceed 50mm.

80mm

to suit faceplate

Note dierent tail

lengths on

breech pipe.

Seal with silicon

if required

Loosen grub screw

underneath spout to realign

spout once tightened into

place.