Bosch HDS7052U/01 Installation guide

Freestanding Dual Fuel Range

Quick Finder:

Safety

Preparation

Installation

Final Steps

1

3

5

7

For Use With

Bosch Dual Fuel Ranges

Installation Instructions

Page is loading ...

Safety Instructions

Preparation

Installation

Final Steps

English • 1

... Our Inspiration

Important Safety Instructions

Please read all instructions before using this appliance.

PARTS PROVIDED:

Anti-Tip Bracket

TOOLS AND PARTS NEEDED:

• Range Power Supply Cord Kit with strain relief

(240V - 30 Amps)*

• Standard Measuring Tape

• Phillips Head Screwdriver

• 1-1/4” Wrench

• Pencil

• T-20 Torx Screwdriver

• 3/8” Nut Driver

• Screws (2) and Anchors (2) for Anti-tip Bracket

(Style will vary depending on mounting surface)

• Pipe Wrench (2)

• Teflon® Tape** or Pipe Joint Compound

(Appropriate for use with LP gas and Natural gas)

• Channel Lock Pliers

• Gas Leak Test Solution

• Level

• Drill and Drill Bit

• Gas Supply Line (Flexible Metal Appliance Connector

or Rigid Pipe)

• Gas Shut Off Valve (If not already present)

• Gloves and Safety Goggles

* Not needed for Canadian installations

**

Teflon

is a registered trademark of

DuPont

Table of Contents

Important Safety Instructions .......................................................................................... 1

Preparation ................................................................................................................... 3

Installation .................................................................................................................... 5

Final Steps ................................................................................................................... 7

• Remove all tape and packaging before using

the range. Destroy the carton and plastic bags

after unpacking the range. Never allow children to

play with packaging material.

• Be sure your appliance is properly installed

and grounded by a qualified technician in

accordance with the National Electrical Code ANSI/

NFPA No. 7 latest edition and local electrical code

requirements.

Important: Local codes vary. Installation, electrical

connections and grounding must comply with all

applicable codes.

• Install only per installation instructions

included in the literature package for this

range.

• Ask your dealer to recommend a qualified

technician and an authorized repair service.

• Know how to disconnect the power to the

range at the circuit breaker or fuse box in and the

gas supply at the shutoff in case of an emergency.

• Do not repair or replace any part of the

appliance unless specifically recommended in

the manuals. All other servicing should be done by

a qualified technician. This may reduce the risk of

personal injury and damage to the range.

• When testing the supply piping system at test

pressures in excess of 1/2 psig (3.5 kPa), the

appliance and its individual shutoff valve must

be disconnected from the gas piping system.

• When testing the supply piping system at test

pressures equal to or less than 1/2 psig (3.5

kPa), the appliance must be isolated from the

gas supply piping system by closing its

individual manual shutoff valve.

• Never modify or alter the construction of a

range by removing leveling legs, panels, wire

covers, anti-tip brackets/screws, or any other part

of the product.

• Do not lift door by door handle. Remove the

door for easier handling and installation. See

Section ‘Removing Oven Door’ in Use and Care

manual.

• Do not store or use combustible materials,

gasoline or other flammable vapors and

liquids in the vicinity of this or any other

appliance.

• WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by a

qualified installer, authorized service agency or the

gas supplier.

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

WARNING

Safety Instructions

Preparation Installation

Final Steps

English • 2

Your Life ...

This appliance has been tested in accordance with the

following standards:

• ANSI Z21.1, Standard for Household Cooking

Appliances (USA)

• CAN 1.1-M81 Interim Reqt # 58 Domestic Cooktops

(CANADA)

• CAN/ CSA-C 22.2 No. 61-M89 Household Cooking

Ranges

In Canada, installation must be in accordance with CAN

1-B149.1 and .2 Installation Codes for Gas Burning

Appliances and/or local codes.

For Massachusetts Installations:

1.Installation must be performed by a qualified or

licensed contractor, plumber or gas fitter qualified

or licensed by the state, province or region where

this appliance is being installed.

2.Shutoff valve must be a “T” handle gas cock.

3.Flexible gas connector must not be longer than 36

inches.

IMPORTANT SAFETY INSTRUCTIONS

Unit is heavy and requires at least two persons or

proper equipment to move.

CAUTION

Before installing, turn power OFF at the service

panel. Lock service panel to prevent power from

being turned ON accidentally.

WARNING

Stepping, leaning or sitting on the doors or drawers

of this range can result in serious injuries and also

cause damage to the range. Do not allow children to

climb or play around the range. The weight of a child

on an open door may cause the range to tip,

resulting in serious burns or other injury.

CAUTION

Do not use the oven or warming drawer (if equipped)

for storage.

WARNING

Do not store items of interest to children in the

cabinets above the range or on the backguard of a

range. Children climbing on the range to reach items

could be seriously injured.

High Altitude Installation Note:

This range is CSA certified for safe operation up to an

altitude of 10,000 ft. without any modifications.

Exception: for use with LP, the range must first be

converted using the LP conversion instructions included

in this literature package.

• All ranges can tip and injury could result. To

prevent accidental tipping of the range,

attach it to the wall, floor or cabinet by

installing the Anti-Tip Device supplied.

• A risk of tip-over may exist if the appliance is

not installed in accordance with these

instructions.

• If the range is pulled away from the wall for

cleaning, service, or any other reason, ensure

that the Anti-Tip Device is properly

reengaged when the range is pushed back

against the wall. In the event of abnormal

usage (such as a person standing, sitting, or

leaning on an open door), failure to take this

precaution could result in tipping of the

range. Personal injury might result from

spilled hot liquids or from the range itself.

WARNING

RANGE TIPPING HAZARD

Safety Instructions

Preparation

Installation

Final Steps

English • 3

... Our Inspiration

Steps 1 through 4: Preparation

Figure 1: Cabinet Preparation

30” Minimum

Centered

30”

Min.

4” Min.

18”

Min.

No Clearance to

Cabinet Wall

Required **

Figure 2: Gas Supply Line and Electrical Outlet Placement

7 1/2"

4 1/2"

13 1/8 "

4"

3 7/8"

4 1/2"

3 1/2"

30"

Place Gas Supply

Line and Electrical

Outlet Here

7 1/2”

4 1/2”

13 1/8”

4” 3 7/8”

3 1/2”

4 1/2”

30”

Figure 3

1 9/16”

Flush

Cabinet Sidewall

Anti-Tip Device

Backwall

1. Install Ventilation

Bosch strongly recommends the installation of a

ventilation hood above this range. For most kitchens a

certified hood rating of not less than 300 CFM is

recommended. The range hood must be installed

according to instructions furnished with the hood.

2. Prepare Cabinets

This unit is designed for installation near adjacent walls

and projecting surfaces constructed of combustible

materials.

Allow a minimum of 30 inches between cabinets where

range is to be installed (See Figure 1)**.

Required Clearances*

From cooktop to materials above (See Figure 1)

There must be a minimum clearance of 30 inches

between the top of the cooking surface and the bottom

of an unprotected wood or metal cabinet.

24 inches is acceptable when the bottom of the wood or

metal cabinet is protected by (a) not less than 1/4" of

flame retardant material which must be covered with

(b) not less than No. 28 MSG sheet metal, 0.015 inch

stainless steel’ or 0.024 inch aluminum or copper.

From range walls to adjacent materials

(See Figure 1)

No clearance is required from unit walls to adjacent

vertical combustible walls on rear, right or left.

Clearance from range top to adjacent vertical walls

must be at least 4”.

NOTE: Some cabinet finishes cannot survive the

temperatures allowed by U.L., particularly self-cleaning

ovens; the cabinets may discolor or stain. This is most

noticeable with laminated cabinets.

3. Prepare Gas Supply Line and

Electrical Outlet

The gas supply line and electrical outlet must be located

in the shaded space in Figure 2.

4. Prepare Walls and Floor

Seal any holes in the walls or floor. Remove any

obstructions (extra electrical or gas connections, etc.) so

that range will rest against wall properly.

*Instructions were determined using standard American cabinets. Standard base cabinets measure 36" high x 24" deep . Cabinets over

the cooking surface and cabinets adjacent to those over the cooking surface measure 13 inches deep from backwall. If nonstandard

cabinets are used, care should be taken to alter dimensions accordingly.

** 12 mm clearance from range sidewall to cabinet required in Canada.

Install Anti-Tip Bracket

1. Adjust height of range and level by rotating the

adjustable leg supports on the bottom of the

range, using 1-1/4" wrench.

2. Measure to locate bracket position as shown in

Figure 8.

3. Secure bracket with 2 screws adequate for

mounting surface, not included. (i.e.; for wood

floor use wood screws, for concrete floor use

concrete anchors and screws.).

Tips:

Tape warming drawer shut to keep it from opening

while installing the range.

During installation, place a portion of the box or a

piece of cloth under the range to protect floors.

To make range lighter and easier to handle, remove

door (see instructions in Use and Care manual).

Safety Instructions

Preparation Installation

Final Steps

English • 4

Your Life ...

Step 5: Prepare Electrical Connection

Install Strain Relief

Place strain relief in knockout below terminal block (See

Figure 4). Feed range cord through hole and strain relief

up to terminal block. Allow for slack in the cord between

the strain relief and terminal block. Once cord length/

slack has been adjusted, attach strain relief per

instructions included with strain relief.

TIP

The knockout panel below the terminal block can be

removed from the range to install the strain relief:

Remove knockout panel from range, install strain

relief in panel and reattach. DO NOT remove entire

range back panel.

Verify that wiring to house is adequate.

Contact your local utility company to verify that the present

electric service to your home is adequate. In some

instances, the size of the wiring to the house and service

switch must be increased to handle the electrical load

demanded by the range.

Verify that wiring inside house is adequate.

Most wiring codes require a separate circuit with separate

disconnect switch and fuses either in the main entrance

panel or in a separate switch and fuse box.

The range requires a three wire 120/240 or 120/208 volt,

30 AMP, 60 Hz AC circuit.

Most local building regulations and codes require that

electrical wiring be done by licensed electricians. Be sure

to install your range according to the electric codes in

place in your region.

General Information

Bosch recommends that the range be installed with a

power cord set (not supplied)*. The electrical rating of the

power cord set must be 120/240 volt, 30 amperes

minimum. The power cord set shall be marked “For Use

with Ranges.” Always use a new power cord.

Note: In Canada, the range is shipped from the factory

with the range cord already installed. Proceed to “Step 7:

Installation - Connect the Gas Supply)

For installations other than those in Canada, connect the

range cord at the terminal block (See next page for

detailed instructions). Access the terminal block by

removing the cover in the lower right hand corner of the

range back panel (See Figure 4). Install the strain relief

(see next column) and the proper connector through the

knockout(s) provided. The electrical supply, including

flexible conduit or power cord, should be restricted to the

shaded areas in Figure 2 (previous page)

WARNING

The strain relief provided with your range

cord must be properly installed.

To prevent electrical shock, the grounding

prong on the range cord should not be cut or

removed under any circumstances. It must be

plugged into a matching grounding type receptacle and

connected to a correctly polarized 240- Volt circuit. If

there is any doubt as to whether the wall receptacle is

properly grounded, have it checked by a qualified

electrician.

Figure 4

Electric Connection (found

behind terminal block

cover)

Gas Connection

Feed

Range

Cord

Through

Strain

Relief in

Knockout

Panel

Here

Figure 5

WARNING

Risk of Electric Shock or Fire. Frame grounded to neutral

through a ground strap. Grounding through the neutral

conductor is prohibited for new branch-circuit installations

(1996 NEC), mobile homes, and recreational vehicles, or in an

area where local codes prohibit grounding through the neutral

conductor.

For installations where grounding through the neutral

conductor is prohibited, (a) disconnect the link from the neutral,

(b) use grounding terminal or lead to ground unit, (c) connect

neutral terminal to lead branch circuit neutral in usual manner

(when the appliance is to be connected by means of a cord kit,

use 4-conductor cord for this purpose).

Use only cord kits rated 125/250 volts (minimum), 30 amperes

and labeled “For Use with Ranges”. Strain relief provided with

cord must be installed per instructions included with cord.

5. Prepare Electrical Connection

Ranges are dual rated for use on either 120/240 VAC or

120/208 VAC. See chart below for power ratings and

circuit breaker sizes based on the supply voltage for

each model.

CAUTION:

Make certain that gas shutoff valve and all burner

controls are in the OFF position before beginning

MODEL: HDS

VOLTS HZ RATING CIRCUIT

A.C. KW BREAKER

120/240 60 6.5 30 AMPS

120/208 60 4.8 30 AMPS

* Not needed for Canadian installations

Safety Instructions

Preparation

Installation

Final Steps

English • 5

... Our Inspiration

Figure 9

Figure 10

Figure 8

Figure 7

Figure 6

Note: DO NOT plug in range at this time. Proceed

to step 7, next page.

Step 6: Installation - Connect Electric

White

Red

Black

Ground Strap

Green Ground Screw

Ground

Strap

Green

Red

White

Black

Red

White

Black

Ground

Strap

Green Ground Screw

Three Wire Connection

The Four Wire Connection is preferred, but where

local codes and ordinances permit grounding through

neutral and/or conversion to four wire is impractical,

unit may be connected to the power supply via a three

wire connection.

1. Disconnect electrical power at breaker box.

2. Remove the terminal block cover to expose the

terminal block (See Figure A).

3. Remove top nut, star washer, and round washer

from each post.

Note: DO NOT remove last round washer, last nut or

internal wiring leads.

4. Attach white wire, round washer, star washer and

nut IN THIS ORDER on top of ground strap on

center post.

5. Attach red wire, round washer, star washer and

nut IN THIS ORDER to left post.

6. Attach black wire, round washer, star washer and

nut IN THIS ORDER to right post (See Figure B).

7. Tighten all connections securely and replace

terminal block cover (See Figure C).

8. Properly secure strain relief (see previous page).

Four Wire Connection (Preferred to three wire connection).

1. Disconnect electrical power at breaker box.

2. Remove the terminal block cover to expose the

terminal block (See Figure A).

3. Remove top nut, star washer, and round washer

from each post.

Note: DO NOT remove last round washer, last nut or

internal wiring leads.

4. Remove screw from bottom end of ground strap.

5. Remove ground strap from center post, rotate so

that wide end is at top and attach wide end to

range through hole below junction box. Attach

green wire on top of ground strap. Tighten Screw

(See Figure D).

6. Attach red wire, round washer, star washer and

nut IN THIS ORDER to left post.

7. Attach white wire, round washer, star washer and

nut IN THIS ORDER to center post.

8. Attach black wire, round washer, star washer and

nut IN THIS ORDER to right post (See Figure E).

9. Tighten all connections securely and replace

terminal block cover.

10. Properly secure strain relief (see previous page).

Safety Instructions

Preparation Installation

Final Steps

English • 6

Your Life ...

The gas connection is located below the back panel of

the range (See Figure 4, Page 4). It is accessible

through the warming drawer access panel or from the

back of the range. To reach access panel, remove

warming drawer.

Shut off main gas supply valve before disconnecting the

old range and leave it off until the new hook-up has

been completed. Don’t forget to relight the pilot on

other gas appliances when you turn the gas back

on.

The range can be installed using rigid pipe or a CSA

International-certified flexible metal appliance connector.

If using a flexible connector, always use a new

connector.

Apply pipe joint compound or Teflon** tape appropriate

for use with LP gas and Natural gas around all male pipe

threads to prevent leaks.

If not already present, install gas shut off valve in an

easily accessible location. Make sure all users know

where and how to shut off the gas supply to the range.

Note: The installer should inform the consumer of

the location of the gas shutoff valve.

Step 7: Installation - Connect Gas Supply

Flexible Connector Method

(see Figure 11, this page)

1. Install male 1/2” flare adaptor at the 1/2” NPT

internal thread of the range inlet. Use a backup

wrench on the elbow fitting to avoid damage.

2. Install male 1/2” or 3/4” flare union adapter on the

NPT internal thread of the manual shutoff valve.

3. Connect flexible metal appliance connector.

4. Make sure circuit breaker is off and then plug range

cord into electrical outlet.

5. Push range back into position insuring that range leg

slides under the anti-tip bracket. The range will sit

3/4” away from the wall when properly installed.

Note: Be careful not to crimp flexible connector!

6. Carefully tip range forward to ensure that anti-tip

bracket engages and prevents tip-over.

Important note for LP users: The range is

shipped from the factory for use with natural gas.

For use with propane (LP) gas, your range must first

be converted using the LP conversion kit.

Figure 11: Flexible Connector Method

Gas Shut-

Off Valve

Flexible

Connector

Regulator

Proceed to “Test for Gas Leaks”, next column.

Test for Gas Leaks

Leak testing is to be conducted by the installer according

to the instructions given in this section.

Turn on Gas. Apply a non-corrosive leak detection fluid

to all joints and fittings in the gas connection between

the shutoff valve and the range. Include gas fittings and

joints in the range if connections may have been

disturbed during installation. Bubbles appearing

around fittings and connections indicate a leak.

If a leak appears, turn off supply line gas shutoff valve

and tighten connections. Retest for leaks by turning on

the supply line gas shutoff valve. When leak check is

complete (no bubbles appear), test is complete. Wipe

off all detection fluid residue. Proceed to Steps 8A and

8B: Final Steps.

gas shut off valve

elbow

nipple

union

elbow

1/2” to 3/4”

gas pipe

Gas Flow to Range

Figure 12: Rigid Pipe Method

elbow:

connect to

regulator here

Rigid Pipe Method

(see Figure 12, this page)

The configuration of the rigid pipe connection will vary

depending on the location of the gas pipe stub. Refer to

Figure 12 for details.

1. Make sure circuit breaker is off and then plug range

cord into electrical outlet.

2. Push range back into position ensuring that range

leg slides under the anti-tip bracket. The range will

sit 3/4” away from the wall when properly installed.

3. Carefully tip range forward to ensure that anti-tip

bracket engages and prevents tip-over.

4. Connect pipe to range at union. Access the

connection through the access panel behind the

warming drawer.

Note: Be careful not to apply pressure to warming

drawer element during rigid pipe installation.

Before you plug in an electrical cord, be sure all

controls are in the OFF position.

CAUTION

NEVER CHECK FOR LEAKS WITH A FLAME.

DO NOT CONTINUE TO THE NEXT STEP UNTIL ALL

LEAKS ARE ELIMINATED.

CAUTION

**

Teflon

is a registered trademark of

DuPont

Safety Instructions

Preparation

Installation

Final Steps

English • 7

... Our Inspiration

Replacement Parts: Visit your Bosch dealer for replacement parts. For a dealer near you contact Bosch Service

at 800-944-2904.

Step 8: Test the Installation

8A. Test Electric Ignition

Turn on power at breaker.

8B. Test/Adjust Flame

High Setting:

The combustion quality of the flame for each burner

must be visually inspected. For propane, the flame

should be blue with yellow tips. For natural gas, it

should be soft blue in color. The flame should carry over,

or surround, the entire burner and should not lift or

blow off the burner.

To inspect, turn the burner on. See Figure 13 for

appropriate flame characteristics.

If the flame is completely or mostly yellow, verify that

the regulator is set for the correct fuel. After

adjustment, retest. If any of the burners continue

to burn mostly or completely yellow, call Bosch

Service 800-944-2904.

Note: With LP use, some yellow tipping on outer cones

is normal.

Low Setting

All burners must also be inspected for carry-over. On

low, the flame should completely surround the burner. If

any of the cooktop burners do not carry over on

the low setting, call Bosch Service 800-944-2904.

Installation is complete at this time.

Flame Characteristics

Figure 13

Yellow Flames:

Further adjustment is required.

Yellow Tips on Outer Cones:

Normal for LP Gas.

Soft Blue Flames:

Normal for Natural Gas.

Some yellow streaking is normal during the

initial start-up.

Allow unit to operate 4-5 minutes and

reevaluate before making adjustments.

WHEN PROPERLY ADJUSTED:

There should be a flame at each burner

port.

There should be no air gap between the

flame and burner.

Caution:

If the display flashes and beeps, the polarity of the

wiring may be reversed. Reversed polarity can

damage the range and can result in electrical shock

hazard. Immediately switch off power at the breaker

and return to step 6.

Select a rangetop burner knob. Push down and turn to

the flame symbol. If the ignitor/spark module is

operating correctly, it will produce a clicking sound.

Once the air has been purged from the supply lines, the

burner should light within four (4) seconds. After burner

lights, turn knob to the off position.

Test each rangetop burner in this fashion.

Call Bosch Service at 800-944-2904 if any of the

burners do not light.

Page is loading ...

BSH reserves the right to change specifications or design without notice. Some models are certified for use in Canada. BSH is not responsible for

products which are transported from the United States for use in Canada. Check with your local Canadian distributor or dealer. BSH Home

Appliances Corporation, 5551 McFadden Avenue, Huntington Beach, CA 92649.

For the most up to date critical installation dimensions by fax, use your fax handset and call 702/833-3600. Use code #8030.

5551 McFadden Avenue, Huntington Beach, CA 92649 • 800-944-2904.

Bosch HDS7052U/01 Installation guide

Bosch HDS7052U/01 Installation guide

in other languages

Related papers

Other documents