Lenco DVP-9413 User manual

Page is loading ...

3

English PORTABLE DVD

Important Safety Instructions

Warning: To reduce the risk of electric shock, do not remove the cover or back. There are no

user-serviceable parts inside. Refer servicing to qualified personnel.

Warning: To prevent fire or electric shock hazard, do not expose the unit to rain or moisture.

Do not expose the Adaptor and portable DVD to water (dripping or splashing) and no objects filled with

liquids, such as vases, should be placed on the unit.

Keep the portable DVD away from direct sunlight and heat source such as radiators or stoves.

Do not block the ventilation openings. Slots and openings on the unit are provided for ventilation. The

openings should never be blocked by placing your portable DVD on a cushion, sofa or other similar

surface.

Do not place the portable DVD on unstable cart, stand, tripod, bracket or table. The unit may fall,

resulting in possible damage or injury.

Never place heavy or sharp objects on the LCD panel or frame.

Only use the AC adapter included with portable DVD. Using any other adapter will void your warranty.

The plug of AC adaptor is used as the disconnect device, the disconnect device shall remain readily

operable.

Unplug the power from the outlet when the unit is not in use.

Attention should be drawn to the environmental aspects of battery disposal.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or

equivalent type.

WARNING: The battery (battery or batteries or battery pack) shall not be exposed to excessive heat

such as sunshine, fire or the like.

WARNING: Excessive sound pressure from earphones or headphones can cause hearing loss.

WARNING: Only use attachments/accessories specified provided by the manufacturer, the portable

DVD is supplied by AC adapter, the AC adapter is used as disconnect device, the disconnect device

shall remain readily operable.

Caution: Danger of explosion if battery is incorrectly replaced, replaced only with the same or equivalent

type (Lithium battery)

This marking indicates that this product should not be disposed with other household wastes

throughout the EU. To prevent possible harm to the environment or human health from

uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of

material resources. To return your used device, please use the return and collection systems

or contact the retailer where the product was purchased. They can take this product for

environmental safe recycling.

Power supply adaptor (For EU only)

Manufacturer: Shenzhen Mass Power Electronics Limited

Model number: EFF0900150E1BA

Use only the power supply listed in the user instructions

4

Safety Precautions

EN EN

WARNING WARNING

RISK OF ELECTRIC SHOCK RISK OF ELECTRIC SHOCK

DO NOT OPEN DO NOT OPEN

Warning: This digital video disc player employs a laser system.

Use of controls, adjustments, or the performance of procedures other than those specified herein may

result in hazardous radiation Exposure.

Warning: To prevent direct exposure to laser beam, do not open the enclosure. Visible laser radiation

when open.

Warning: Never stare directly into the laser beam.

Caution: Do not install this product in a confined space such as a book case or similar unit.

Warning: when the unit using by child, parents must make sure to let the child understand all contents in

Instruction book how battery using to guarantee using battery correctly all the time.

Warning: when find battery overheat, swell or dour, please stop using battery and contact service centre

for getting replacement.

Warning: do not charging battery on the place of insufficient ventilation such as: mattress, sofa, cushion,

soft mat......

Warning: we will not take any responsibility if user incorrectly use battery, not following our warning

instruction label on the battery case.

Warning: more than 250mm USB extension cord is prohibited to use for USB port.

Notes on Copyrights:

It is forbidden by law to copy, broadcast, show, broadcast via cable, play in public, or rent copyrighted

material without permission.

This product features the copy protection function developed by Macrovision. Copy protection signals

are recorded on some discs. When recording and playing the pictures of these discs picture noise will

appear. This product incorporates copyright protection technology that is protected by method claims of

certain U.S. Patents and other intellectual property rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection technology must be authorized by Macrovision

Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized

by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

SERIAL NUMBER:

You can find the serial number on the back of the unit. This number is unique to this unit and not

available to others. You should record requested information here and retain this guide as a permanent

record of your purchase.

Model No.

Serial No.

Date of Purchase

5

nE nE

egrahc egrahc

tcapmi gnorts tcapmi gnorts

C°04 taeh revo C°04 taeh revo

WARNING

Do not ingest the battery, Chemical Burn Hazard (The remote control supplied with) This product

contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe

internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If

the battery compartment does not close securely, stop using the product and keep it away from children.

If you think batteries might have been swallowed or placed inside any part of the body, seek immediate

medical attention. To prevent possible hearing damage, do not listen at high volume levels for long

periods.

Identification of Controls

Main Unit

1. PLAY/ PAUSE

2. STOP

3. SOURCE

4. VOL-

5. VOL+

6. MENU

7. ▲/▼/◄/► (up/down/right/left)

Select an item in the menu. OK key confirms menu selection.

when playing, VCD, DVD, if available:

right: fast forward

21 20

6

left: fast reverse

up: previous track

down: next track

8. ENTER

9. OPEN

10. SETUP

11. SD/MMC

12. USB

13. AV OUT

14. Earphone Socket

15. COAXIAL

16. ON/OFF

17. DC IN 9-12V

18. ANT

19.

20.

21.

HDMI

Identification of Controls

1. SOURCE

DVD/CARD/USB.

2. MUTE

Disable Audio output.

3. 0-9 NUMBER BUTTON

Selects numbered items in a menu.

4. INFO

To display the playtime and status information.

Battery Charging Indicator

Illuminates green flashing when the battery is charging.

Illuminates green when the battery is fully charged.

Power Indicator

Illuminates red when the unit is switched on.

7

5. 10+ RECALL

In order to select a track 10 or greater, first press 10+, For example; select track 12, first press 10+, and

then press number 2 button.

6. PBC/FAV

PBC on/off switch (VCD).

7. AUDIO

DVD: Press AUDIO repeatedly during playback to hear a different audio language or audio track, if

available.

CD/VCD: Press AUDIO repeatedly during playback to hear a different audio channel (Left, Right, Mix,

Stereo).

8. PLAY/PAUSE

Press PLAY/PAUSE once to pause playback, pressing PLAY/PAUSE a second time will resume the

playback.

9. STOP

When this button is pressed once, the unit records the stopped point, from where playback will resume if

PLAY ( ) is pressed afterwards. But if the STOP button is pressed again instead of PLAY ( ) there will

be no resume function.

10. STEP/TV/RADIO

Step the motion in DVD mode.

11. VOL+

Adjust volume

12. Forward Skip

Go to next chapter/ track.

13. Reverse Skip

Go to previous chapter/track to the beginning.

14.

BUTTON

Press the BUTTON allows skipping ahead at 5-level speed (X2->X4->X8->X16->X32->PLAY),

pressing PLAY returns to normal playback.

15. BUTTON

Press the BUTTON allows skipping back at 5-level speed (X2->X4->X8->X16->X32->PLAY), press

PLAY to return to normal playback.

16.

Turn on/off the power.

17. SEARCH

Go to time point, title or chapter you want in DVD Mode.

18. SUBTITLE

Press SUBTITLE repeatedly during playback to see different subtitle languages.

19. ANGLE

DVD: Pressing ANGLE will change the view angle, on DVDs that support this feature.

20. TITLE

Return to DVD title menu.

21. OK

Confirms menu selection.

22. SETUP

Accesses or removes setup menu.

8

23. VOL-

Adjust volume

24. REPEAT

Press REPEAT during playback to select a desired repeat mode.

DVD: you can play select repeat chapter/title/all.

CD/VCD: you can select repeat track/all.

Mp3: you can select repeat shuffle/random/single/repeat one/repeat folder/folder.

25. SLOW

Press Slow repeatedly to enter slow playback, and cycle between different speeds. The speeds are 1/2,

1/4, 1/8, 1/16, and normal.

26. PROGRAM

DVD/VCD/CD: The program function enables you to store your favourite tracks from the disc. Press the

PROGRAM button, then PROGRAM MENU will appear on screen, now you can use the number key to

direct input the titles, chapters or tracks number and select PLAY option. TO resume normal playback,

press PROGRAM and select clear program option on the program menu, press PROGRAM again to exit

program menu, Mp3 has function Folder/File list.

27. ZOOM

DVD/VCD: Use ZOOM to enlarge or shrink the video image.

1. Press ZOOM during playback or still playback to activate the Zoom function. The square frame

appears briefly in the right bottom of the picture.

2. Each press of the ZOOM button changes the TV screen in the following sequence:

2X size → 3X size → 4X size → 1/2 size → 1/3 size → 1/4size → normal size

JPEG: Use ZOOM to enlarge or shrink the picture.

1. Press 'ZOOM'.

2. Used " " to enlarge, or " " to shorten the picture.

Use the ▲▼◄► button to move through the zoomed picture.

28. RED/GREEN/YELLOW/BLUE KEY

Some specific function in DVB mode.

9

SETUP Menu Setting

General Setup Page

Press SETUP to get the setup menu. Use direction buttons ▲▼◄► to select the preferred item. After

finishing the settings, press SETUP again to normal display.

The following menu items can be changed:

GENERAL: selects the GENERAL PAGE menu.

AUDIO: selects the AUDIO PAGE menu.

VIDEO: selects the VIDEO PAGE menu.

PREFERENCE: selects the PREFERENCE PAGE menu.

General Setup Page

TV DISPLAY: selects the aspect ratio of the playback picture.

4:3 PANSCAN: if you have a normal TV and want both sides of the picture to be trimmed or formatted to

fit your TV screen.

4:3 LETTERBOX: if you have a normal TV. In this case, a wide picture with black bands on the upper

and lower portions of the TV screen will be displayed.

16:9: wide screen display.

TFT DISPLAY

Selects the aspect ratio during playback.

Angle Mark

Displays current angle setting information on the right hand corner of the TFT screen if available on the

disc.

OSD Language

You can select your own preferred language settings.

Closed Captions

Closed captions are data that are hidden in the video signal of some discs. Before you select this

function, please ensure that the disc contains closed captions information and your TV set also has this

function.

Screen Saver

This function is used to turn the screen saver On or Off.

10

Auto Standby

This function is used to select auto standby settings after 3 or 4 hours.

3 HOURS: the unit will turn to standby mode after 3 hours if there is no interaction from user within this

period of time.

4 HOURS: the unit will turn to standby mode after 4 hours if there is no interaction from user within this

period of time.

OFF: the auto standby function is disabled, and unit will stay in “on” mode even if no interaction from

user.

Audio Setup Page

Downmix

This option allows you to set the stereo analog output of your DVD Player.

LT/RT: Select this option if your DVD Player is connected to a Dolby Pro Logic decoder.

Stereo: Select this option when output delivers sound from only the two front speakers.

Digital Output

The function is used to select the SPDIF Output: SPDIF Off, SPDIF/RAW, SPDIF/PCM.

SPDIF Off: Turns off the SPDIF output.

SPDIF/RAW: If you have connected your DIGITAL AUDIO OUT to a multi-channel decoder/receiver.

SPDIF/PCM: Only if your receiver is not capable of decoding multi-channel audio.

Dolby digital

The options included in Dolby Digital Setup are: 'Dual Mono' and 'Dynamic'.

Dual Mono

Stereo: The Left mono sound will send output signals to the Left speaker and the Right mono sound will

send output signals to the Right speaker.

L-Mono: The Left mono sound will send output signals to the Left speaker and the Right speaker.

R-Mono: The Right mono sound will send output signals to the Left speaker and the Right speaker.

Mix-Mono: The Left and the Right mixed mono sound will send output signals to the Left and the Right

speakers.

Dynamic

Dynamic range compression.

11

Video Setup Page

Brightness, Contrast, Hue, Saturation: setting the video quality.

Preference Page

TV Type

Selecting the colour system that corresponds to your TV when AV outputs. This DVD Player is

compatible with both NTSC and PAL.

PAL - Select this if the connected TV is a PAL system. It will change the video signal of a NTSC disc and

output in PAL format.

NTSC-Select this if the connected TV is an NTSC system. It will change the video signal of a PAL disc

and output in NTSC format.

Auto: Change the video signal output automatically according to the playing disk format.

Audio: Selects a language for audio (if available).

Subtitle: Selects a language for subtitle (if available).

Disc Menu: Selects a language for disc menu (if available).

Default: Back to the factory setting.

12

Parameters and specifications

Electronical parameters

Item Standard requirement

Power requirements

: AC 100-240 V, 50/60 Hz

Power consumption

: <12W

Operating humidity

: 5 % to 90 %

Output

VIDEO OUT

: 1 Vp-p (75Ω)

AUDIO OUT

: 1.4 Vrms (1 KHz, 0 dB)

Audio

: Speaker: 1WX2, Headphones output

System

Laser

:Semiconductor laser, wavelength 650 nm

Signal system

: NTSC / PAL

Frequency response

: 20Hz to 20 kHz(1dB)

Signal-to-noise ratio

:More than 80 dB (ANALOG OUT connectors only)

Dynamic range

:More than 85 dB (DVD/CD)

Note: Design and specifications are subject to change without prior notice.

Battery Parameters

Battery Specifications:

Output: 7.4V

Charge/Discharge Time:

Standard charge time: 3h ~ 4h

Storage and work circumstances:

1. Storage circumstances Temperature Humidity

6 months -20°C~+45°C 65±20%

1 week -20°C~+45°C 65±20%

2. Work circumstances Temperature Humidity

Standard charge 0°C~+45°C 65±20%

Standard discharge -20°C~+65°C 65±20%

13

First Time Installation

After all connections have been made properly, switch on TV and make sure the receiver is connected to

the Main Power. Press Power button to switch receiver on. If you are using the receiver for the first time

or restored to Factory Default, the Main Menu will appear on your TV screen.

(1) Select [OSD Language] and press RIGHT/LEFT key to select a language.

(2) Select [Country] and press RIGHT/LEFT key to select your country of residence.

(3) Select [Channel Search] and press RIGHT or OK key to begin Automatic channel search.

(4) Once channel tuning is complete, you are now ready to watch TV.

Basic Operation

Program Manage Settings

To access the Menu, press the SETUP button and select [Program]. The Menu provides options to

adjust the Program Manage Settings. Select an option and press OK or RIGHT to adjust that setting.

Press the EXIT button to exit the Menu.

14

Program Edit

To edit your program preferences (lock, skip, favourite, move or delete), you will need to enter the

Program Edit Menu. Password not required at first use, only after lock channel, you can enter the default

password '000000' to access.

Set Favourite Program/s

You can create a shortlist of favourite programs that you can easily access. Set Favourite TV or Radio

program:

1. Select the preferred program then press the FAVOURITE button. A heart-shaped symbol will appear

and the program is marked as a favourite.

2. Repeat the previous step to select more Favourite programs.

3. To confirm and exit the Menu, press the EXIT key.

Disable Favourite TV or Radio Program:

Press the FAV buton on the Remote Control with the heart-shaped symbol.

View Favourite Programs:

1. Press the Fav button and the Favourite Menu will appear.

2. Press UP/DOWN to select your Favourite Programs.

3. Press OK to select your favourite program.

Delete a TV or Radio Program/s

1. Select the Program and then press the BLUE button, A message will appear. Press OK to delete the

program.

2. Repeat the previous step to select more programs to delete.

Skip TV or Radio Program/s

1. Select the program you would like to skip and press the GREEN button, A skip symbol is displayed.

The program is marked as a skip.

2. Repeat the previous step to select more programs.

3. To confirm and exit the menu, press EXIT key.

Disable a skip TV or Radio Program:

Press the GREEN button on the skip program with the skip symbol.

Move a TV or Radio Program/s

1. Select the preferred program then press the RED button. A move symbol will appear.

2. Press UP/DOWN to move the program.

3. Press OK to confirm.

4. Repeat the above steps to move more channels.

Lock Program/s

You can lock selected programs for restricted view.

Lock a TV or Radio Program:

15

1. Select the preferred program then press the YELLOW button. A lock-shaped symbol is displayed.

The program is now marked as locked.

2. Repeat the previous step to select more programs.

3. To confirm and exit the menu, press the EXIT button.

4. Press the YELLOW button to disable the locked program.

5. To view the locked program, you will be require to enter either the default, or the modified Password.

(refer to system settings “Set Password”)

Sort

Sort your channels from the following options:

[LCN] - Sort the channels in ascending order.

[Name] - Sort the channels in alphabetical order.

[Service ID] - Sort the channels according to the station.

LCN (Logical channel number)

Set LCN on or off.

Video Setting

To access the Menu, press SETUP then select [Picture]. The Menu provides options to adjust the video

settings. Press UP/DOWN to select an option and press RIGHT/LEFT to adjust that setting. Press EXIT

to exit the menu.

Aspect Ratio

You must set the display format to either 4:3 PanScan, 4:3 Letter Box, 4:3 Full, 16:9 Wide Screen, 16:9

PillarBox or Auto to get the maximum display when watching TV.

Resolution

If the video does not appear correctly, change the setting. This setting is to match the most common

setting for HDMI.

[576i] for PAL system TV.

[576P]: for PAL system TV.

[720P]: for NTSC or PAL system TV.

[1080I]: for NTSC or PAL system TV.

[1080P]: for NTSC or PAL system TV.

16

TV format

If the video does not appear correctly, you need to change the settings. This should match the most

common setting for TVs in your country.

[NTSC]: for NTSC system TV.

[PAL]: for PAL system TV.

Channel Search

To access the menu, press SETUP and select [Search Channel].

The Menu provides options to adjust the Search Channel settings.

Select an option and press RIGHT/LEFT to adjust the settings.

Press EXIT to exit the Menu.

Auto Search

Search and install all channels automatically. This option overwrites all preset channels.

1. Select [Auto Search] and press OK or RIGHT to start channel search.

2. To cancel channel search, press EXIT.

Manual Search

Install new channels manually. This option adds new channels without changing the current channels

list.

1. Select [Manual Search] then press OK or RIGHT. The channel search screen will appear.

17

2. Press the RIGHT/LEFT key to select the channel frequency.

3. Press OK to start searching channels.

If a channel is found, it is saved and added to the channels list. If channels can’t be found, then exit the

menu.

Country

Select your country of residence.

Antenna Power

Supply Power to Antenna.

Time Setting

To access the Menu, press MENU then select [Time]. The Menu provides options to adjust the time

settings. Press UP/DOWN to select an option and press RIGHT/LEFT to adjust the settings. Press EXIT

to exit the menu.

Time offset

Select auto or manual for GMT offset adjustments.

Country Region

Country Region is set automatically when you set the country at channel search menu.

Time Zone

Select the Time Zone Offset when [Time Offset] is set to Manual.

18

Option

To access the Menu, press SETUP and select [Option]. The menu provides options to adjust the OSD

Language, Subtitle Language and Audio Language. Select an option and press RIGHT/LEFT to adjust

the setting. Press EXIT to exit The Menu.

OSD Language

Select an OSD language.

Audio Language

Select the preferred audio language for watching TV channels. If the language is not available, the

default program language will be used.

Subtitle Language

Select the preferred subtitle language.

Digital Audio

Set the desired audio format at the HDMI slot: PCM, Raw HDIM On, Raw HDMI Off, Off (if available).

System Setting

To access the Menu, press SETUP and select [System].The menu Provides options to adjust the system

settings. Press the UP/DOWN key to select an option and press RIGHT/LEFT to adjust the setting.

Press EXIT to exit the Menu.

Set Password

Set or change the password for Locked programs. Enter your old Password or the default password

'000000'. You will then be asked to enter your new password. To confirm re-enter your new password.

Once it is confirmed, press EXIT to exit the Menu.

Master password '888888'

19

Restore Factory Default

Reset your Set Top Box to the Default Factory Settings. In Main Menu select [Restore Factory Default]

and press OK or RIGHT to select. Enter your password or the default password '000000' and press OK

to confirm. This option will delete all preset channels and settings.

Information

View model, hardware and software information.

Software update

USB

To access the Menu, press the SETUP button and select USB.

Multimedia

Switch to USB mode and plug in USB to view files.

Photo Configure

Set the parameters for viewing photographs.

Movie Configure

Set the parameters for displaying movie subtitles.

20

Technical Specifications

Item Sub Item Parameter

Tuner

Input Frequency

170~230MHz

470~860MHz

RF Input level -79dBm(T), -75dBm(T2)

IF Bandwidth 7MHz and 8MHz

Modulation QPSK, 16QAM, 64QAM, 128QAM(T2), 256QAM(T2)

Video

Decoder Format

MPEG4 AVC/H.264 HP@L4

HEVC/H.265 HT@L4

MPEG2 [email protected]

Output Format 480i, 480p,576i, 576P, 720P, 1080i, 1080P, 4:3 and 16:9

Output Port HDMI

Troubleshooting

Problem Potential Reasons What to do

No picture Power isn't connected Connect the power

The power switch is not on Switch on the power

Screen shows “No

Signal”

DVB-T cable not connected Plug in the DVB-T cable

Incorrect setting Reset setting

No sound from

speaker

Sound on mute Turn off mute function

Incorrect sound track Try another sound track

Only sound, no image

on the screen

No or incorrect connection with AV

cable

Make sure cables are connected correctly

The program is a radio program Press <TV/RADIO> key to shift into TV mode

Remote Control is not

responding

The battery is exhausted Change battery

Remote Control is not facing or

close enough to the Set Top Box

Adjust the position of the Remote Control and

move closer to the unit

The image stopped

suddenly or mosaic

The signal is too weak Strengthen the signal

- The DVP-9413 can only receive non encrypted free TV channels.

21

Guarantee

Lenco offers service and warranty in accordance with the European law, which means that in case of

repairs (both during and after the warranty period) you should contact your local dealer.

Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If

this unit is opened or accessed by a non-official service center in any way, the warranty expires.

This device is not suitable for professional use. In case of professional use, all warranty obligations of

the manufacturer will be voided.

Disclaimer

Updates to Firmware and/or hardware components are made regularly. Therefore some of the

instruction, specifications and pictures in this documentation may differ slightly from your particular

situation. All items described in this guide for illustration purposes only and may not apply to particular

situation. No legal right or entitlements may be obtained from the description made in this manual.

Disposal of the Old Device

This symbol indicates that the relevant electrical product or battery should not be disposed of as

general household waste in Europe. To ensure the correct waste treatment of the product and

battery, please dispose them in accordance to any applicable local laws of requirement for

disposal of electrical equipment or batteries. In so doing, you will help to conserve natural

resources and improve standards of environmental protection in treatment and disposal of

electrical waste (Waste Electrical and Electronic Equipment Directive).

Service

For more information and helpdesk support, please visit www.lenco.com Lenco Benelux BV;

Thermiekstraat la, 6361 HB, The Netherlands.

Page is loading ...

Lenco DVP-9413 User manual

Related papers

Other documents