KT-AES50

Klark Teknik KT-AES50 Quick start guide

  • Hello! I am an AI chatbot trained to assist you with the Klark Teknik KT-AES50 Quick start guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What safety precautions should be taken when using the Klark Teknik KT-AES50?
    Where can I find information regarding the warranty terms and conditions for the Klark Teknik KT-AES50?
    What are the potential consequences of mishandling the Klark Teknik KT-AES50 during disposal?
    What is the purpose of the protective earthing connection in the Klark Teknik KT-AES50?
Quick Start Guide
KT-AES50
AES50 Network Module with up to 48 Bidirectional Channels
2 3Quick Start GuideKT-AES50
Terminals marked withthis
symbol carryelectrical
currentof su cient
magnitude to constitute risk of electric
shock. Useonly high-quality
commercially-available speaker cables
with plugs pre-installed. Allother
installation or modi cation should be
performed only by quali edpersonnel.
This symbol, wherever it
appears, alerts you to the
presence of uninsulated
dangerous voltage inside the enclosure -
voltage that may be su cient to
constitute a risk ofshock.
This symbol, wherever it
appears, alerts you to
important operating and
maintenance instructions in the
accompanying literature. Please read
themanual.
Caution
To reduce the risk of electric
shock, do not remove the
top cover (or the rear section). No user
serviceable parts inside. Refer servicing to
quali edpersonnel.
Caution
To reduce the risk of  re or
electric shock, do not expose
this appliance to rain and moisture.
Theapparatus shall not be exposed to
dripping or splashing liquids and no
objects  lled with liquids, such as vases,
shall be placed on the apparatus.
Caution
These service instructions
are for use by quali ed
service personnel only. Toreduce the
risk of electric shock do not perform any
servicing other than that contained in the
operation instructions. Repairshave to be
performed by quali ed servicepersonnel.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus nearwater.
6. Clean only with dry cloth.
7. Do not block any ventilation
openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources
such as radiators, heat registers, stoves,
orother apparatus (including ampli ers)
thatproduceheat.
9. Do not defeat the safety purpose
of the polarized or grounding-type plug.
Apolarized plug has two blades with one
wider than the other. A grounding-type
plug has two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety. Ifthe
provided plug does not  t into your outlet,
consult an electrician for replacement of
the obsoleteoutlet.
10. Protect the power cord from being
walked on or pinched particularly at plugs,
convenience receptacles, and the point
where they exit from theapparatus.
11. Use only attachments/accessories
speci ed by themanufacturer.
12. Use only with
the cart, stand,
tripod, bracket, or
table speci ed by
the manufacturer, or
sold with the
apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during
lightning storms or when unused for long
periods oftime.
14. Refer all servicing to quali ed
service personnel. Servicing is required
when the apparatus has been damaged
in any way, such as power supply cord or
plug is damaged, liquid has been spilled
or objects have fallen into the apparatus,
the apparatus has been exposed to rain
or moisture, does not operate normally,
orhas beendropped.
15. The apparatus shall be connected to
a MAINS socket outlet with a protective
earthingconnection.
16. Where the MAINS plug or an
appliance coupler is used as the
disconnect device, thedisconnect device
shall remain readilyoperable.
17. Correct disposal of
this product: This symbol
indicates that this product
must not be disposed of
with household waste,
according to the WEEE Directive
(2012/19/EU) and your national law.
This product should be taken to a
collection center licensed for the recycling
of waste electrical and electronic
equipment (EEE). The mishandling of this
type of waste could have a possible
negative impact on the environment and
human health due to potentially
hazardous substances that are generally
associated with EEE. At the same time,
your cooperation in the correct disposal of
this product will contribute to the e cient
use of natural resources. For more
information about where you can take
your waste equipment for recycling,
please contact your local city o ce, or
your household waste collection service.
MUSIC Group accepts no liability for any
loss which may be su ered by any person
who relies either wholly or in part upon
any description, photograph, or statement
contained herein. Technical speci cations,
appearances and other information
are subject to change without notice.
All trademarks are the property of their
respective owners. Midas, Klark Teknik,
Lab Gruppen, Lake, Tannoy, Turbosound,
TC Electronic, TC Helicon, Behringer,
Bugera, DDA and TC Applied Technologies
are trademarks or registered trademarks
of MUSIC Group IP Ltd. © MUSIC Group IP
Ltd. 2015 All rights reserved.
For the applicable warranty terms and
conditions and additional information
regarding MUSIC Group’s Limited
Warranty, please see complete details
online at music-group.com/warranty.
Las terminales marcadas con
este símbolo transportan
corriente eléctrica de
magnitud su ciente como para constituir
un riesgo de descarga eléctrica.
Utilice solo cables de altavozde alta
calidad con clavijas TSde6,3mm
pre-instaladas (puedeadquirirlos en
comercios especializados en audio).
Cualquierotra instalación o modi cación
debe ser realizada únicamente por un
técnico cuali cado.
Este símbolo, siempre que
aparece, leadvierte de la
presencia de voltaje
peligroso sin aislar dentro de la caja;
estevoltaje puede ser su ciente para
constituir un riesgo dedescarga.
Este símbolo, siempre que
aparece, leadvierte sobre
instrucciones operativas y de
mantenimiento que aparecen en la
documentación adjunta. Por favor,
leaelmanual.
Atención
Para reducir el riesgo
de descarga eléctrica,
no quite la tapa (olaparte posterior).
Nohay piezas en el interior del equipo
que puedan ser reparadas por el usuario.
Sies necesario, póngase en contacto con
personal cuali cado.
Atención
Para reducir el riesgo
de incendio o descarga
eléctrica, no exponga este aparato a la
lluvia, humedad o alguna otra fuente que
pueda salpicar o derramar algún líquido
sobre el aparato. Nocoloque ningún
tipo de recipiente para líquidos sobre
elaparato.
Atención
Las instrucciones de servicio
deben llevarlas a cabo
exclusivamente personal cuali cado.
Paraevitar el riesgo de una descarga
eléctrica, no realice reparaciones que
no se encuentren descritas en el manual
de operaciones. Lasreparaciones deben
ser realizadas exclusivamente por
personalcuali cado.
1. Lea las instrucciones.
2. Conserve estas instrucciones.
3. Preste atencn a todas
lasadvertencias.
4. Siga todas las instrucciones.
5. No use este aparato cerca del agua.
6. Limpie este aparato con un poseco.
7. No bloquee las aberturas de
ventilación. Instale el equipo de acuerdo
con las instrucciones del fabricante.
8. No instale este equipo cerca de
fuentes de calor tales como radiadores,
acumuladores de calor, estufas u otros
aparatos (incluyendo ampli cadores)
quepuedan producir calor.
9. No elimine o deshabilite nunca la
conexn a tierra del aparato o del cable
de alimentacn de corriente. Unenchufe
polarizado tiene dos polos, uno de los
cuales tiene un contacto más ancho que
el otro. Una clavija con puesta a tierra
dispone de tres contactos: dos polos y
la puesta a tierra. El contacto ancho y el
tercer contacto, respectivamente, son
los que garantizan una mayor seguridad.
Siel enchufe suministrado con el equipo
no concuerda con la toma de corriente,
consulte con un electricista para cambiar
la toma de corriente obsoleta.
10. Coloque el cable de suministro de
energía de manera que no pueda ser
pisado y que esté protegido de objetos
a lados. Aserese de que el cable de
suministro de energía esté protegido,
especialmente en la zona de la clavija y en
el punto donde sale del aparato.
11. Use únicamente los dispositivos o
accesorios especi cados por elfabricante.
12. Use únicamente
la carretilla,
plataforma, trípode,
soporte o mesa
especi cados por el
fabricante o
suministrados junto con el equipo.
Altransportar el equipo, tengacuidado
para evitar daños y caídas al tropezar con
algúnobstáculo.
13. Desenchufe el equipo durante
tormentas o si no va a utilizarlo durante un
periodo largo.
LIMITED WARRANTY
LEGAL DISCLAIMER
Important Safety
Instructions
Instrucciones de
seguridad
10 11Quick Start GuideKT-AES50
Warning
Failure to observe the following warnings may lead to fatality or
serious injury from  re or electric shock.
Before installing the card, you must refer to the owner’s manual of
the host device or to klarkteknik.com to verify that your host device
supports this card, and to verify the number of cards that can be
installed in combination with other MIDAS or third-party cards.
Do not attempt to disassemble or modify the card.
Donot apply excessive force to board connectors or
other board components. Mishandling of board may
lead to shock,  re hazard, or equipment failure.
Disconnect the power cable from the main unit before
installing this card to eliminate shock hazard.
Caution
Failure to observe the following precautions may lead to personal
injury, or may result in damage to equipment or other property.
Do not touch the board’s metallic leads (pins)
whenhandling the card. Pins are sharp and may
causeinjury.
The card is electrostatic-sensitive.
Before handling the card, you should brie y touch
the main unit’s metal casing with your bare hand
so as to drain o any static charge from your body.
MUSIC Group assumes no responsibility for data loss,
equipment damage, or injury caused by inappropriate
handling or usage.
εο౏൝
ฃ०ܧ௛
6. ឱၺࣱ࣌ຎพశַ̘ǎ
7. ឱӉ܅܌ᤱ᮴Աǎ߸ᜊశַ̘
௒ឱᥗཱིԉࠓᄋឮ௛ǎ
8. ឱӉ࠳శַ̘߸ᜊڛམ຺ᬅ
ᤄݡ఍ජ
, ༰ߖੌЦ̘߳ၸམ
᧛ᄋ᝻ܭӋ઻ҫ஋٩ǎ
9. ឱӉሩᬕ౞মତ݁ੌ଍ڢ
ତ݁ᄋ߸МᜊᎷǎ଍ڢତ݁௨
ႁˑ˕ତ܌଍གྷԤʸ˕଍ڢ݁
౟ੈǎᔫᬥ᠏ଣΚᄋତ݁ˁᤡՍ
১ᄋତऑ
, ឱ੾ႄࢻట૲ʸ˕Ս
ᤡᄋତऑǎ
10. ݱؔεઑႄ຺ጴΏЦˁᜃ᡼
ᢇੌ҉ᆢ
, ࡀЦญਔႄ຺ତ݁Ǎܴၺ
᤮ତऑԤ᝻ܭᤍ଍ܬǎ
11. ឱԷΏၺԉࠓ૊ࠁᄋᬅ࡜᝻ܭ
֘ᦢ͉ǎ
12. ឱԷΏၺԉ
ࠓ૊ࠁᄋੌᬥ᠏
ᩚ׭ᄋ੥ଏᢽ
,
౷ߖ, ʽᝉ౷஄
౷֘ಹߖǎᔫΏ
ၺ੥ଏᢽ౐ୄᤃ
᝻ܭ
, ឱญਔ߸М஋Ꮇ᝻ܭ, ̀
Г੥ଏᢽ֘᝻ܭϛωᏬԫ͟ǎ
13. ᥆᫆ႄᭈᲟੌ᫃ఱˁΏၺశ᝻
ܭ௒
, ឱફѤႄ຺ତ݁ǎ
14. ੟ధ፦οڪᮍႁՍಬᄋ፦ο
̢ցᤊᛢǎ᝻ܭԫ૰௒ᭋᤊᛢ፦
ο
, Δݡႄ຺ጴੌႄ຺ତ݁ԫ૰,
͵ุЛੌफྮᗁЛ᝻ܭа
, ᝻ܭᥔ
ᭂ๹ੌԫ໾
, ᝻ܭˁᑠ൥ࣣᤃͼ
ੌᜃ୒گǎ
15. శ᝻ܭᤍ଍ႄ຺௒ʸࠁ᜷ధ
଍ڢεઑǎ
16. ᔫႄ຺ତ݁ੌ٩
ЧᏺՍ٩ၺͼளႄ
ᜊᎷ
, अैε᝾߳̈́
ܬ̇ᬥ௒ԼஶΨ୳
ͼ࿅ঘǎ
17. శַ̘̪ᤡၺ̇
๓ફ
2000 ዜ̀ʿ
ڢӞ
, శַ̘̪ᤡၺ
̇᭥མࣝජό౏
͉ʿǎ
18. ឱӉ࠳ႄ්ఓ᭜
ڛϹே௴
, ༣຺ੌዞ
ͬᄋᤀམဘܓ˘ǎ
ࠬ̇͋Ͷڃڛ൦ឮ௛˻ଣ҃ᄋ
Мᦋੌᦋ͌ଢᤙǍڐྠੌܧ௛
Ꮼᤶੈᄋ૰݀MUSIC Groupˁ
᠈͋Ͷ᠋͋ǎ઀సԡஞ֘ܲ
᜻ᔫధటஉিˁԴᛢᤱᅽǎ
੟ధᄋ׹ಗڪ˟ЦՋᒮ੟ధ
Ꮹᄋ᠊̘ǎMidasKlark Teknik
Lab Gruppen-BLFTannoy
TurbosoundTC ElectronicTC Helicon
BehringerBugeraDDA֘TC Applied
Technologie
T௨MUSIC Group IP
Ltd.
ОՄᄋ׹ಗੌญг׹ಗǎ
© MUSIC Group IP Ltd. 2015ྡీ
੟ధǎ
ధУᮄˮᬸڅεοᄋᤡၺ౏൝
ԤЦ߳ᄲУθ্ឱᄇᬇ
music-
group.com/warranty
Ꭻቤಋᄻߺ஠
ᄋឡጻθ্ǎ
12 13Quick Start GuideKT-AES50
3. Connector Plate
Dual RJ45 bidirectional ports
In 48 kHz mode, the two ports act as a
dual-redundant connection.
Each port transmits channels 1-48
In 96 kHz mode, each port carries
24 channels:
Port 1: channels 1-24
Port 2: Channels 25-48
Po rt indicator LEDs
Green indicates proper functioning
Red indicates an error with the
port connection
1. Introduction
The KT-AES50 card is a multichannel audio interface
expansion card for the Klark Teknik DN9650/DN9652
Network Bridge that allows up to 48 channels of
AES50 format audio to be converted to a di erent
protocol or sample rate. This sample-rate conversion
therefore allows AES50 networks operating at 96 kHz
to connect to AES50 networks operating at 48 kHz.
This expansion card provides 48 channels of AES50
digital audio operating at either 48 kHz or 96 kHz on
two connectors.
2. Installation
Before you install the KT-AES50 card in the network
module slot of the DN9650/DN9652 Network Bridge,
you must check klarkteknik.com to verify that
the unit’s host  rmware supports this card.
We recommend that you periodically check your
unit’s product page for  rmware updates.
Caution – before installing the KT-AES50
into the DN9650/DN9652 Network Bridge,
you must make sure that the unit’s power switch
is turned o . Malfunctions or electrical shock may
occur otherwise.
To install an interface I/O card:
DN9650/DN9652
1. Make sure that the host unit’s power
is turned o .
2. Loosen the 19 screws fastening the
chassis cover, then remove the chassis cover
from the main chassis. Keep the cover and the
screws in a safe place.
3. Before removing the KT-AES50 card from its
protective bag, we recommend touching the
grounded metal chassis of the console to prevent
electrostatic discharges a ecting the sensitive
electronic components. It is generally a good
idea to hold the card either by the face plate or
by the two small handles, but never touching the
components on the circuit board directly.
4. Identify the Network Module connectors (two
male 40 pin vertical connectors). Align the
KT-AES50 female connectors with the DN9650
connectors and apply vertical pressure being
very careful not to bend the pins. Push the
card all the way into the slot to ensure that the
contacts of the card are correctly inserted.
5. Fasten the card using the included screws
(2 in the faceplate and 2 to the rear of the PCB).
Be aware that damage or malfunctions may
occur if the card is not fastened.
6. Replace the chassis cover and replace all screw
before the unit is powered on.
Requirements
DN9650/DN9652 Network Bridge.
14 15Quick Start GuideKT-AES50
Other important information
1. Register online. Please register
your new MUSIC Group equipment right
after you purchase it by visiting klarkteknik.
com. Registering your purchase using our
simple online form helps us to process your
repair claims more quickly and e ciently.
Also, read the terms and conditions of our
warranty, ifapplicable.
2. Malfunction. Should your
MUSICGroup Authorized Reseller not be
located in your vicinity, you may contact
the MUSIC Group Authorized Ful ller for
your country listed under “Support” at
klarkteknik.com. Shouldyour country not
be listed, please check if your problem
can be dealt with by our “OnlineSupport”
which may also be found under “Support” at
klarkteknik.com. Alternatively, please submit
an online warranty claim at klarkteknik.com
BEFORE returning theproduct.
1. Registro online.
Le recomendamos que registre su nuevo
aparato MUSIC Group justo después de
su compra accediendo a la página web
klarkteknik.com. Elregistro de su compra
a través de nuestro sencillo sistema online
nos ayudará a resolver cualquier incidencia
que se presente a la mayor brevedad
posible. Además,aproveche para leer los
términos y condiciones de nuestra garantía,
si es aplicable en sucaso.
2. Averías. En el caso de que no
exista un distribuidor MUSIC Group en las
inmediaciones, puede ponerse en contacto
con el distribuidor MUSIC Group de su
país, queencontrará dentro del apartado
“Support” de nuestra página web klarkteknik.
com. En caso de que su país no aparezca
en ese listado, acceda a la sección “Online
Support” (quetambiénencontrará dentro del
apartado “Support” de nuestra páginaweb)
y compruebe si su problema aparece descrito
y solucionado allí. De forma alternativa,
envíenos a través de la página web una
solicitud online de soporte en periodo de
garantía ANTES de devolvernos el aparato.
1. Enregistrez-vous enligne.
Prenez le temps d’enregistrer votre produit
MUSIC Group aussi vite que possible
sur le site Internet klarkteknik.com.
Le fait d’enregistrer le produit en ligne
nous permet de gérer les réparations
plus rapidement et plus e cacement.
Prenezégalement le temps de lire les
termes et conditions de notre garantie.
2. Dysfonctionnement. Si vous
n’avez pas de revendeur MUSIC Group près
de chez vous, contactez le distributeur
MUSIC Group de votre pays: consultez la liste
des distributeurs de votre pays dans la page
“Support” de notre site Internet klarkteknik.
com. Si votre pays n’est pas dans la liste,
essayez de résoudre votre problème avec
notre “aideen ligne” que vous trouverez
également dans la section “Support” du site
klarkteknik.com. Vous pouvez également
nous faire parvenir directement votre
demande de réparation sous garantie par
Internet sur le site klarkteknik.com AVANT de
nous renvoyer le produit.
Important
information
Aspectos
importantes
Informations
importantes
4. Speci cations
Connectors
RJ45 2
Input/Output Characteristics
Channels of input/output @ 48 kHz 48, both ports (dual redundant)
Channels of input/output @ 96 kHz
1-24, port 1 (independent)
25-48, port 2 (independent)
Sample rates 48 kHz / 96 kHz
Sample word length 24 Bit
Clock synchronisation selectable host unit, external (AES50)
Latency
min. 70 μs (AES50),
additional 1 ms with SRC
Cable Length
Ethernet cat 5e 100 m
18 19Quick Start GuideKT-AES50
Responsible Party Name: MUSIC Group Research UK Limited
Address: Klark Industrial Park,
Walter Nash Road,
Kidderminster. Worcestershire.
DY11 7HJ. England.
Phone Number: +44 1562 741515
KT-AES50
complies with the FCC rules as mentioned in the following paragraph:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his
own expense.
Important information:
Changes or modi cations to the equipment not expressly approved by
MUSIC Group can void the user’s authority to use the equipment.
Klark Teknik
KT-AES50
FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
/