Nikon 200mm F/2 User manual

Category
Camera lenses
Type
User manual

This manual is also suitable for

Sv
AF-S NIKKOR 200mm f/2G ED VR
Gebruikshandleiding
Manuale d’uso
Návod k obsluze
Užívateľská príručka
Manualul utilizatorului
Посібник користувача
P.2
Pg. 16
S. 30
P. 44
Pág. 58
S. 72
Cтр. 86
P. 100
Pag. 114
Str. 128
Str. 142
Pag. 156
Cтор. 170
184
198
212
뵓넯덻
2010
Printed in Japan
TT0G02(G4)
7MAA75G4-02 G01
AF-S NIKKOR 200mm f/2G ED VR
16
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Notes on Safety Operations
CAUTION
Do not disassemble
Touching the internal parts of the camera or lens could result in injury. Repairs
should be performed only by qualified technicians. Should the camera or lens
break open as the result of a fall or other accident, take the product to a Nikon-
authorized service representative for inspection after unplugging the product
and/or removing the battery.
Turn off immediately in the event of malfunction
Should you notice smoke or an unusual smell coming from the camera or
lens, remove the battery immediately, taking care to avoid burns. Continued
operation could result in injury.
After removing or disconnecting the power source, take the product to a Nikon-
authorized service representative for inspection.
Do not use the camera or lens in the presence of flammable gas
Operating electronic equipment in the presence of flammable gas could result in
an explosion or fire.
Do not look at the sun through the lens or viewfinder
Viewing the sun or other strong light sources through the lens or viewfinder
could cause permanent visual impairment.
Keep out of reach of children
Particular care should be taken to prevent infants from putting the batteries or
other small parts into their mouths.
17
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Observe the following precautions when handling the camera
and lens
Keep the camera and lens unit dry. Failure to do so could result in a fire or
electric shock.
Do not handle or touch the camera or lens unit with wet hands. Failure to do
so could result in electric shock.
When shooting with back-lighting, do not point the lens at the sun or allow
sunlight to pass directly down the lens as this may cause the camera to
overheat and possibly cause a fire.
When the lens will not be used for an extended period of time, attach both
front and rear lens caps and store the lens away from direct sunlight. Failure
to do so could result in a fire, as the lens may focus sunlight onto a flammable
object.
18
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Thank you for purchasing the AF-S NIKKOR 200mm f/2G ED VR lens.
Before using this lens, please read these instructions and refer to your
camera's user's manual.
Nomenclature
1 Lens hood (pg. 26)
2 Lens hood screw (pg. 26)
3 Focus operation button (Focus Lock/
Memory recall/AF Start) (pg. 22)
4 Lens rotating position index (pg. 25)
5 Focus ring (pg. 21)
6 Distance scale (pg. 25)
7 Distance index line (pg. 25)
8 Depth-of-field indicators (pg. 25)
9 Memory set button (pg. 22)
! Vibration reduction ON/OFF ring
switch (pg. 24)
" Mounting index
# Lens mount rubber gasket (pg. 28)
$ CPU contacts (pg. 28)
% Tripod collar ring fastening screw
(pg. 25)
& Built-in rotating tripod collar (pg. 25)
( Strap eyelet
) Slip-in filter holder knob (pg. 26)
~ Slip-in filter holder (pg. 26)
+ Focus mode switch (pg. 21)
, Focusing limit switch (pg. 21)
- Vibration reduction mode switch
(pg. 24)
. Focus operation selection switch
(AF-L/MEMORY RECALL/AF-ON)
(pg. 22)
/ Sound monitor switch (pg. 22)
( ): reference page
20
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Major features
The Nano Crystal Coat deposited on some of the lens elements ensures that
fine, clear images can be reproduced under various shooting conditions, from
the sunny outdoors to spotlighted interior scenes.
This lens features AF-L, which locks focus during autofocus, AF-ON, which
activates autofocus, and MEMORY RECALL, which saves and recalls selected
focus distances.
By enabling vibration reduction (VR ), slower shutter speeds (approximately
four stops*) can be used, thus increasing the range of usable shutter speeds,
particularly when hand-holding the camera. (*Based on results achieved
under Nikon measurement conditions. The effects of vibration reduction may
vary according to shooting conditions and use.)
AF-I/AF-S Teleconverters TC-14E/TC-14E
/TC-17E /TC-20E/TC-20E /
TC-20E are usable.
Important
When mounted on Nikon DX format digital SLR cameras, such as the D300-Series
and D90, the lens’ angle of view becomes 8° and its 35mm equivalent focal
length is approx. 300mm.
Usable cameras and available functions
There may be some restrictions or limitation for available functions. Refer to camera's
user's manual for details.
Cameras
Function
Exposure
(shooting) mode
VR AF
Focus
lock
Memory
recall
AF start
on the
lens
P
*1
SAM
Nikon digital SLR (Nikon FX/DX format)
cameras, F6, F5, F100, F80-Series/
N80-Series*, F75-Series/N75-Series*,
F65-Series/N65-Series*
✓✓✓
Pronea 600i/6i*, Pronea S*
2
✓✓✓
F4-Series, F90X/N90s*, F90-Series/
N90*, F70-Series/N70*
*
3
✓✓*
4
*
3
*
5
✓✓
——
F60-Series/N60*, F55-Series/N55-Series*,
F50-Series/N50*, F-401x/N5005*, F-401s/
N4004s*, F-401/N4004*
——
✓✓✓
F-801s/N8008s*, F-801/N8008*,
F-601
M/N6000*
——
✓✓
——
F3AF, F-601/N6006*, F-501/N2020**,
Nikon MF cameras (except F-601
M/
N6000*)
——
: Possible
: Not possible VR: Vibration reduction AF: Autofocus
*Sold exclusively in the USA
**Sold exclusively in the USA and Canada
*1: P includes AUTO and Vari-Program System (Scene modes).
*2: Manual (M) is not available.
*3: When the focus operation selection switch is set to AF-ON, autofocus begins as soon as the
focus operation button is pressed while the shutter-release button pressed halfway.
21
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
*4: Press the memory set button or a focus operation button while pressing the shutter
release button halfway.
*5: Possible, with limited restrictions
Focusing
Set your camera focus mode according to the chart below:
Cameras
Camera
focus
mode
Lens focus mode switch
A/M M/A M
Nikon digital SLR (Nikon FX/DX format)
cameras, F6, F5, F4-Series, F100,
F90X/N90s*, F90-Series/N90*,
F80-Series/N80-Series*,
F75-Series/N75-Series*, F70-Series/N70*,
F65-Series/N65-Series*, Pronea 600i/6i*,
Pronea S
AF
(C/S)
Autofocus
with manual
override
(AF priority)
Autofocus
with manual
override
(MF priority)
Manual
focus
(Electronic
rangefinder
can be used.)
MF
Manual focus
(Electronic rangefinder can be used.)
F60-Series/N60*, F55-Series/N55-Series*,
F50-Series/N50*, F-801s/N8008s*,
F-801/N8008*, F-601
M/N6000*,
F-401x/N5005*, F-401s/N4004s*,
F-401/N4004*
AF
(C/S)
MF
Manual focus
(Electronic rangefinder can be used,
except with the F-601
M/N6000*.)
*Sold exclusively in the USA
AF: Autofocus MF: Manual focus
A/M (Autofocus with manual override. AF priority) mode and M/A
(Autofocus with manual override. MF priority) mode
M/A: Autofocus can be overridden by manually focusing with
the focus ring.
A/M: Autofocus can be overridden by manually focusing with
the focus ring, but focus ring detection sensitivity is lower
than in M/A mode. Use this mode to avoid canceling the
AF setting by unintentionally moving the focus ring.
1
Set the focus mode switch to A/M or M/A.
2
Autofocus can be manually overridden by rotating the focus ring while
pressing the shutter release button halfway, pressing the AF-ON button on
the camera or pressing a focus operation button (with focus operation set to
AF-ON) on the lens.
3
Pressing the shutter release button halfway, pressing the AF-ON button on
the camera again or pressing a focus operation button on the lens again will
cancel manual override and return the lens to autofocus mode.
To limit the range of autofocus
This function is only available with autofocus.
FULL: If the subject is sometimes closer than 5 m (16.4 ft.),
set the switch to FULL.
–5m: If the subject is always 5 m (16.4 ft.) or more away, set
the switch to –5m to reduce focusing time.
22
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Focus operation selection switch and focus operation
button (See page 20 for compatible cameras.)
Use the focus operation selection switch to choose a function of the focus
operation buttons.
Position of focus operation
selection switch
Focus operation button
function
AF-L Focus lock
MEMORY RECALL Memory recall
AF-ON AF start (AF-ON) on the lens
Press one of four focus operation buttons to activate each
function.
Focus lock (AF-L)
This function is only compatible with autofocus.
1
Set the focus mode switch to A/M or M/A.
2
Set the focus operation selection switch to AF-L.
3
During autofocus mode, focus can be locked by pressing one of the focus
operation buttons.
Focus remains locked while a focus operation button is pressed and held down.
The AF-L function can be engaged either from the camera or from the lens.
Memory recall (MEMORY RECALL)
: The lens beeps when memory recall is operated.
: Memory recall operates without the beep sound.
The following operation is with the sound monitor switch set to .
1
Focus on a subject and press the memory set button to save
the focus distance.
The lens will beep when the focused distance is correctly
saved.
When the focus distance is not correctly saved, the distance
scale ring will revolve back and forth some 10 times, while
the lens will emit one short and three long beeps. In this
case, repeat procedure to save focus distance.
Memory set is possible regardless of the setting of the focus mode or focus
operation selection switch.
The focus distance is saved even when the camera is turned off or the lens is
detached from the camera.
2
Set the focus operation selection switch to MEMORY RECALL.
23
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
3
Press a focus operation button. After the lens beeps twice, fully press the
shutter release button to take the picture.
The saved focus distance is recalled when a focus operation button is pressed
even when the shutter release button is pressed halfway.
To take pictures at the saved focus distance, hold the focus operation button
down and fully press the shutter release button.
The lens reverts from memory recall to autofocus or manual focus when the
focus operation button is released.
Autofocus (AF) start on the lens (AF-ON)
1
Set the focus mode switch to A/M or M/A.
2
Set the focus operation selection switch to AF-ON.
3
Press a focus operation button to take pictures.
Autofocus is activated while a focus operation button is pressed and held down.
The AF-ON function can be engaged either from the camera or from the lens.
Vibration reduction mode (VR )
Basic concept of vibration reduction
Strength of vibrations
Strong
Weak
Set the vibration reduction
mode switch to NORMAL.
Panning shots
Camera shake
Camera shake when using a tripod
Set the vibration reduction
mode switch to ACTIVE.
Number of vibrations
Low
High
Strong
camera shake when
taking pictures
from a moving
vehicle
When taking pictures
When taking panning shots
When taking pictures from
a moving vehicle
When taking pictures using
a tripod
Set the vibration reduction mode switch to either NORMAL or ACTIVE.
Set the vibration reduction mode switch to NORMAL.
Set the vibration reduction mode switch to ACTIVE.
Set the vibration reduction mode switch to either NORMAL or ACTIVE.
24
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Setting the vibration reduction ON/OFF ring switch
ON: The effects of camera shake are reduced while the
shutter-release button is pressed halfway and also at
the instant the shutter is released. Because vibration is
reduced in the viewfinder, auto/manual focusing and
exact framing of the subject are easier.
OFF: The effects of camera shake are not reduced.
Setting the vibration reduction mode switch
Set the vibration reduction ON/OFF ring switch to ON and choose a vibration
reduction mode with the vibration reduction mode switch.
NORMAL: The vibration reduction mechanism primarily
reduces the effects of camera shake. The effects
of camera shake are also reduced with horizontal
and vertical panning.
ACTIVE: The vibration reduction mechanism reduces
the effects of camera shake, such as that which
occurs when taking pictures from a moving
vehicle, whether it be normal or more intense
camera shake. In this mode, camera shake is not
automatically distinguished from panning motion.
Notes on using vibration reduction
If this lens is used with cameras that do not have the vibration reduction
function (pg. 20), set the vibration reduction ON/OFF ring switch to OFF. With
the Pronea 600i/6i camera, in particular, battery power may become quickly
depleted if this switch is left ON.
After pressing the shutter-release button halfway, wait until the image in the
viewfinder stabilizes before pressing the shutter-release button the rest of the
way down.
Due to the characteristics of the vibration reduction mechanism, the image
in the viewfinder may be blurred after the shutter is released. This is not a
malfunction.
When taking panning shots, be sure to set the vibration reduction mode
switch to NORMAL. If the camera is panned in a wide arc, compensation for
camera shake in the panning direction is not performed. For example, only the
effects of vertical camera shake is reduced with horizontal panning.
Do not turn the camera off or remove the lens from the camera while vibration
reduction is operating. Failure to observe this note could result in the lens
sounding and feeling as if an internal component is loose or broken when it is
shaken. This is not a malfunction. Turn the camera on again to correct this.
With cameras featuring a built-in flash, vibration reduction does not function
while the built-in flash is charging.
When using a tripod, set the vibration reduction ON/OFF ring switch to ON
to reduce the effect of camera shake. Nikon recommends the switch be set to
ON when using the camera on an unsecured tripod head or with a monopod.
But when camera shake is very slight, the vibration reduction function may
conversely increase the effect of camera shake by the movement of the system.
In such a case, set the vibration reduction ON/OFF ring switch to OFF.
25
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Vibration reduction does not function when the AF-ON button on the camera
or a focus operation button on the lens is pressed.
Depth of field
Depth-of-fi eld
indicators
Distance index line
Approximate depth of field can be determined
by checking the depth-of-field indicators. If your
camera has a depth-of field preview (stop-
down) button or lever, depth of field can be pre-
viewed through the camera viewfinder.
This lens is equipped with the Internal Focusing (IF) system. As the shooting
distance decreases, the focal length also decreases.
The distance scale does not indicate the precise distance between the subject
and the camera. Values are approximate and should be used only as a general
guide. When shooting distant landscapes, depth of field may influence operation
and the subject may appear in focus at a position that is closer than infinity.
For more information, see page 226.
Setting the aperture
Use the camera to adjust the aperture setting.
Using a built-in rotating tripod collar
When using a tripod, attach it to the lens’ tripod collar instead of the camera.
When holding the camera by its handgrip and rotating the camera with the
lens in its tripod collar, your hand may bump into the tripod, depending on
the tripod in use.
It’s possible to detach the tripod collar by removing the tripod collar lock
screw. For details on this procedure, contact your nearest Nikon service center
or representative office.
Changing the camera position
Loosen the tripod collar ring fastening screw (
1
).
Depending on camera position (vertical or
horizontal), turn the lens to an appropriate lens
rotating position index (
2
) and tighten the screw
(
3
).
26
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
The built-in flash and vignetting
To prevent vignetting, do not use the lens hood.
Cameras
Vignetting occurs at any shooting distance.
F65-Series/N65-Series*, F60-Series/N60*,
F55-Series/N55-Series*, F50-Series/N50*,
F-601/N6006*, Pronea 600i/6i*, Pronea S
*Sold exclusively in the USA
Using the lens hood
Lens hoods minimise stray light and protect the lens.
Attaching the hood
• Fully tighten the lens hood screw (
2
).
If the lens hood is not correctly attached,
vignetting may occur.
To store the lens hood, attach it in the
reverse position.
Slip-in filter holder
Always use a (52mm screw-on) filter. A 52mm Screw-on Neutral Color NC Filter
is attached to the filter holder when shipped from the factory.
1
Press down on the slip-in filter holder knob, and
turn counterclockwise until the white line on the
knob is at a right angle to the axis of the lens.
2
Pull the slip-in filter holder from the lens body
3
Detach the attached filter from the filter holder.
4
Screw a filter onto the side of the filter holder
marked with the words “Nikon” and “JAPAN”.
The slip-in filter holder can be attached with the
“Nikon” and “JAPAN” facing either the lens or
camera side without any effect on your pictures.
Slip-in Circular Polarizing Filter C-PL3L (optional)
Blocks reflections from nonmetallic surfaces such as glass and water.
When a Slip-in Circular Polarizing Filter C-PL3L is attached, the focus distance
is different from when a 52mm screw-on filter is attached. The distance scale
is shifted from the correct position. The closest focused distance is extended
slightly.
The memory set position may change slightly when using focus preset. Attach
the C-PL3L filter before using the memory set function.
27
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Recommended focusing screens
Various interchangeable focusing screens are available for certain Nikon SLR
cameras to suit any picture-taking situation. The ones recommended for use
with this lens are:
Screen
ABCE
EC-B
EC-E
G1
G2
G3 G4 J L M U
Camera
F6
F5+DP-30
F5+DA-30
(+0.5)
: Excellent focusing
: Acceptable focusing
Slight vignetting or moiré patterns appear in the viewfinder, but not on the film.
: Not available
( ) : Indicates degree of exposure compensation needed (center-weighted
metering only). For F6 cameras, compensate by selecting “Other screen“ in
Custom Setting “b6: Screen comp.“ and setting the EV level to -2.0 to +2.0
in 0.5 EV steps. When using screens other than type B or E, “Other screen“
must be selected even when the required compensation value is “0“ (no
compensation required). For F5 cameras, compensate using Custom Setting
#18 on the camera body. See user’s manual of the camera body for more
details.
Blank box means not applicable. Since type M screen can be used for
both macro photography at a magnification ratio of 1:1 or above and for
photomicrography, it has different applications than other screens.
Important
For F5 cameras, only EC-B, EC-E, B, E, J, A, L focusing screens are usable in
Matrix Metering.
28
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Lens care
Be careful not to hold the camera body when the lens is attached, as this may
cause damage to the camera (lens mount). Be sure to hold both the lens and
camera when carrying.
When the lens is mounted on a camera, do not pick up or hold the camera
and lens by the lens hood.
Be careful not to allow the CPU contacts to become dirty or damaged.
If the lens mount rubber gasket is damaged, be sure to visit the nearest Nikon-
authorized service representative for repair.
Clean lens surfaces with a blower brush. To remove dirt and smudges, use a soft,
clean cotton cloth or lens tissue moistened with ethanol (alcohol) or lens cleaner.
Wipe in a circular motion from the center to outer edge, taking care not to leave
traces or touch other parts of the lens.
Never use organic solvent such as thinner or benzene to clean the lens.
When storing the lens in its case, attach both the front and rear lens caps.
When the lens will not be used for an extended period of time, store it in a
cool, dry place to prevent mold and rust. Be sure to store the lens away from
direct sunlight or chemicals such as camphor or naphthalene.
Do not get water on the lens or drop it in water as this will cause it to rust and
malfunction.
Reinforced plastic is used for certain parts of the lens. To avoid damage, never
leave the lens in an excessively hot place.
Standard accessories
Dedicated slip-on front lens cap
Rear Lens Cap
Lens Hood HK-31
Semi-soft Case CL-L1
Dedicated slip-in filter holder
52mm Screw-on Neutral Color NC Filter
• Strap LN-1
Important
The slip-in filter holder, with a 52mm screw-on filter attached, should be
inserted in the lens at all times.
Optional accessories
52mm screw-on filters (except circular polarizing filter )
• Slip-in Circular Polarizing Filter C-PL3L
AF-S Teleconverters TC-14E /TC-17E /TC-20E
29
Jp
En
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
Specifications
Type of lens: G-type AF-S NIKKOR lens with built-in CPU and Nikon
bayonet mount
Focal length: 200mm
Maximum aperture: f/2
Lens construction: 13 elements in 9 groups (3 ED, 1 Super ED and some
Nano Crystal Coat-deposited lens elements), as well as 1
protective glass
Angle of view: 12°20´ with 35mm (135) format Nikon film SLR cameras
and Nikon FX format digital SLR cameras
8° with Nikon DX format digital SLR cameras
50´ with IX240 system cameras
Distance information: Output to camera
Focusing: Nikon Internal Focusing (IF) system, autofocus using a
Silent Wave Motor; manually via separate focus ring
Vibration reduction: Lens-shift method using voice coil motors (VCMs)
Shooting distance
scale:
Graduated in meters and feet from 1.9 m (7 ft) to
infinity (∞)
Closest focusing
distance:
1.9 m (6.2 ft.)
No. of diaphragm
blades:
9 pcs. (rounded)
Diaphragm: Fully automatic
Aperture range: f/2 to f/22
Exposure
measurement:
Via full-aperture method with cameras with CPU
interface system
Focusing limit switch: Provided; two ranges available: FULL (∞–1.9 m), or ∞–5 m
Tripod collar: Rotatable through 360°, lens rotating position index at
90°, only tripod collar detachable
Dimensions: Approx. 124 mm dia. x 203.5 mm extension from the
camera’s lens-mount flange
Weight: Approx. 2,930 g (6.5 lbs)
Specifications and designs are subject to change without any notice or obligation on the
part of the manufacturer.
89
Jp
Ua
De
Fr
Es
Se
Ru
Nl
It
Ck
Ch
Kr
2010
Printed in Japan
TT0G02(G4)
7MAA75G4-02 G01
1 / 1

Nikon 200mm F/2 User manual

Category
Camera lenses
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document