Campbell Scientific NL116 Owner's manual

Brand: Campbell Scientific

Model: NL116

Category: Measuring, testing & control

Type: Owner's manual

This manual is also suitable for

NL116 and CompactFlash

INSTRUCTION MANUAL

NL116 Ethernet and

CompactFlash

Module

Revision: 6/15

Campbell Scientific, Inc.

Limited Warranty

“Products manufactured by CSI are warranted by CSI to be free from defects in

materials and workmanship under normal use and service for twelve months

from the date of shipment unless otherwise specified in the corresponding

product manual. (Product manuals are available for review online at

www.campbellsci.com.) Products not manufactured by CSI, but that are resold

by CSI, are warranted only to the limits extended by the original manufacturer.

Batteries, fine-wire thermocouples, desiccant, and other consumables have no

warranty. CSI’s obligation under this warranty is limited to repairing or

replacing (at CSI’s option) defective Products, which shall be the sole and

exclusive remedy under this warranty. The Customer assumes all costs of

removing, reinstalling, and shipping defective Products to CSI. CSI will return

such Products by surface carrier prepaid within the continental United States of

America. To all other locations, CSI will return such Products best way CIP

(port of entry) per Incoterms ® 2010. This warranty shall not apply to any

Products which have been subjected to modification, misuse, neglect, improper

service, accidents of nature, or shipping damage. This warranty is in lieu of all

other warranties, expressed or implied. The warranty for installation services

performed by CSI such as programming to customer specifications, electrical

connections to Products manufactured by CSI, and Product specific training, is

part of CSI's product warranty. CSI EXPRESSLY DISCLAIMS AND

EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE. CSI hereby disclaims,

to the fullest extent allowed by applicable law, any and all warranties and

conditions with respect to the Products, whether express, implied or

statutory, other than those expressly provided herein.”

Assistance

Products may not be returned without prior authorization. The following

contact information is for US and international customers residing in countries

served by Campbell Scientific, Inc. directly. Affiliate companies handle

repairs for customers within their territories. Please visit

www.campbellsci.com to determine which Campbell Scientific company serves

your country.

To obtain a Returned Materials Authorization (RMA), contact CAMPBELL

SCIENTIFIC, INC., phone (435) 227-9000. After an application engineer

determines the nature of the problem, an RMA number will be issued. Please

write this number clearly on the outside of the shipping container. Campbell

Scientific’s shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____

815 West 1800 North

Logan, Utah 84321-1784

For all returns, the customer must fill out a “Statement of Product Cleanliness

and Decontamination” form and comply with the requirements specified in it.

The form is available from our web site at www.campbellsci.com/repair. A

completed form must be either emailed to repair@campbellsci.com or faxed to

(435) 227-9106. Campbell Scientific is unable to process any returns until we

receive this form. If the form is not received within three days of product

receipt or is incomplete, the product will be returned to the customer at the

customer’s expense. Campbell Scientific reserves the right to refuse service on

products that were exposed to contaminants that may cause health or safety

concerns for our employees.

Precautions

DANGER — MANY HAZARDS ARE ASSOCIATED WITH INSTALLING, USING, MAINTAINING, AND WORKING ON OR AROUND

TRIPODS, TOWERS, AND ANY ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS, ENCLOSURES,

ANTENNAS, ETC. FAILURE TO PROPERLY AND COMPLETELY ASSEMBLE, INSTALL, OPERATE, USE, AND MAINTAIN TRIPODS,

TOWERS, AND ATTACHMENTS, AND FAILURE TO HEED WARNINGS, INCREASES THE RISK OF DEATH, ACCIDENT, SERIOUS

INJURY, PROPERTY DAMAGE, AND PRODUCT FAILURE. TAKE ALL REASONABLE PRECAUTIONS TO AVOID THESE HAZARDS.

CHECK WITH YOUR ORGANIZATION'S SAFETY COORDINATOR (OR POLICY) FOR PROCEDURES AND REQUIRED PROTECTIVE

EQUIPMENT PRIOR TO PERFORMING ANY WORK.

Use tripods, towers, and attachments to tripods and towers only for purposes for which they are designed. Do not exceed design

limits. Be familiar and comply with all instructions provided in product manuals. Manuals are available at www.campbellsci.com or

by telephoning (435) 227-9000 (USA). You are responsible for conformance with governing codes and regulations, including safety

regulations, and the integrity and location of structures or land to which towers, tripods, and any attachments are attached. Installation

sites should be evaluated and approved by a qualified engineer. If questions or concerns arise regarding installation, use, or

maintenance of tripods, towers, attachments, or electrical connections, consult with a licensed and qualified engineer or electrician.

General

• Prior to performing site or installation work, obtain required approvals and permits. Comply

with all governing structure-height regulations, such as those of the FAA in the USA.

• Use only qualified personnel for installation, use, and maintenance of tripods and towers, and

any attachments to tripods and towers. The use of licensed and qualified contractors is highly

recommended.

• Read all applicable instructions carefully and understand procedures thoroughly before

beginning work.

• Wear a hardhat and eye protection, and take other appropriate safety precautions while

working on or around tripods and towers.

• Do not climb tripods or towers at any time, and prohibit climbing by other persons. Take

reasonable precautions to secure tripod and tower sites from trespassers.

• Use only manufacturer recommended parts, materials, and tools.

Utility and Electrical

• You can be killed or sustain serious bodily injury if the tripod, tower, or attachments you are

installing, constructing, using, or maintaining, or a tool, stake, or anchor, come in contact with

overhead or underground utility lines.

• Maintain a distance of at least one-and-one-half times structure height, 20 feet, or the distance

required by applicable law, whichever is greater, between overhead utility lines and the

structure (tripod, tower, attachments, or tools).

• Prior to performing site or installation work, inform all utility companies and have all

underground utilities marked.

• Comply with all electrical codes. Electrical equipment and related grounding devices should

be installed by a licensed and qualified electrician.

Elevated Work and Weather

• Exercise extreme caution when performing elevated work.

• Use appropriate equipment and safety practices.

• During installation and maintenance, keep tower and tripod sites clear of un-trained or non-

essential personnel. Take precautions to prevent elevated tools and objects from dropping.

• Do not perform any work in inclement weather, including wind, rain, snow, lightning, etc.

Maintenance

• Periodically (at least yearly) check for wear and damage, including corrosion, stress cracks,

frayed cables, loose cable clamps, cable tightness, etc. and take necessary corrective actions.

• Periodically (at least yearly) check electrical ground connections.

WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS,

THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR

MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS SUCH AS SENSORS, CROSSARMS,

ENCLOSURES, ANTENNAS, ETC.

Table of Contents

PDF viewers: These page numbers refer to the printed version of this document. Use the

PDF reader bookmarks tab for links to specific sections.

1. Introduction ................................................................. 1

2. Cautionary Statements ............................................... 1

3. Initial Inspection ......................................................... 2

4. Quickstart .................................................................... 2

4.1 Physical Setup ...................................................................................... 2

4.2 Communicating via Ethernet................................................................ 3

4.2.1 Step 1: Configure Datalogger ....................................................... 3

4.2.2 Step 2: LoggerNet Setup ............................................................... 4

4.2.3 Step 3: Connect ............................................................................. 7

4.3 Programming the Datalogger to Save Data to the CompactFlash

Card .................................................................................................. 7

4.4 CF Card Data Retrieval ........................................................................ 8

5. Overview ...................................................................... 9

5.1 Buttons and Status LED ..................................................................... 10

5.2 Power ................................................................................................. 10

5.3 CF Card Data Retention ..................................................................... 10

6. Specifications ........................................................... 10

7. Operation ................................................................... 12

7.1 TCP/IP Functionality ......................................................................... 12

7.1.1 Communicating Over TCP/IP ..................................................... 12

7.1.1.1 Data Callback ................................................................... 12

7.1.1.2 Datalogger-to-Datalogger Communication ...................... 13

7.1.2 HTTP Web Server ...................................................................... 14

7.1.3 FTP ............................................................................................. 15

7.1.3.1 FTP Server ....................................................................... 15

7.1.3.2 FTP Client ........................................................................ 17

7.1.4 Telnet .......................................................................................... 18

7.1.5 Ping ............................................................................................. 18

7.1.6 Serial Server ................................................................................ 18

7.1.6.1 Serial Input ....................................................................... 18

7.1.6.2 Serial Output .................................................................... 18

7.1.7 TCP ModBus .............................................................................. 19

7.1.8 DHCP .......................................................................................... 19

7.1.9 DNS ............................................................................................ 19

7.2 File Formats ....................................................................................... 19

7.2.1 Data Files .................................................................................... 19

7.2.2 Program Files .............................................................................. 20

7.2.3 Power-up Files (Powerup.ini) ..................................................... 20

Table of Contents

7.2.3.1

Creating and Editing Powerup.ini .................................... 20

7.2.3.2 Applications ..................................................................... 21

7.2.3.3 Program Execution .......................................................... 22

7.2.3.4 Example Powerup.ini Files .............................................. 22

7.2.4 Camera Files .............................................................................. 23

7.3 Programming ..................................................................................... 23

7.3.1 The CardOut() Instruction .......................................................... 23

7.3.2 Program Examples ..................................................................... 24

7.3.2.1 Ring Mode ....................................................................... 24

7.3.2.2 Fill-and-Stop Mode.......................................................... 24

7.3.2.3 Mixed Modes ................................................................... 25

7.3.3 Table Size and Mode .................................................................. 26

7.4 CF Card Data-Retrieval Details ......................................................... 26

7.4.1 Via a Communication Link ........................................................ 26

7.4.1.1 Fast Storage/Data-Collection Constraints ........................ 26

7.4.2 Transporting CF Card to Computer ............................................ 27

7.4.2.1 Converting File Formats .................................................. 27

7.4.2.2 Reinserting the Card ........................................................ 28

7.4.2.3 Card Swapping ................................................................ 28

Appendix

CF Card Maintenance ............................................. A-1

A.1 Formatting CF Card ........................................................................ A-1

A.1.1 Windows Explorer ................................................................... A-1

A.1.2 CR1000KD ............................................................................... A-2

A.1.3 LoggerNet File Control ............................................................ A-2

A.2 Checking CF Card Integrity ............................................................ A-3

Figures

4-1. NL116 attached to a CR1000 .............................................................. 2

4-2. DevConfig setup .................................................................................. 3

4-3. Setup screen (EZ View) Datalogger Type ........................................... 4

4-4. Setup screen (EZ View) Connection Type .......................................... 5

4-5. Setup screen (EZ View) IP Port Settings............................................. 6

4-6. Setup screen (EZ View) Datalogger Settings ...................................... 7

5-1. NL116 Ethernet/CompactFlash

Module ............................................ 9

7-1. Datalogger home page ....................................................................... 15

7-2. FTP root directory ............................................................................. 16

7-3. FTP CRD directory ........................................................................... 16

7-4. CardConvert ...................................................................................... 28

Table

7-1. Powerup.ini Commands .................................................................... 21

NL116 Ethernet and CompactFlash

Module

1. Introduction

Campbell Scientific’s NL116 Ethernet/CompactFlash

Module provides two

independent capabilities: (1) it enables Ethernet communications and (2) stores

data on a removable CompactFlash

(CF) card. It allows the datalogger to

communicate over a local network or a dedicated Internet connection via

Ethernet. It also expands on-site data storage and provides the user with a

convenient method of transporting data from the field back to the office. This

small, rugged communication device connects to the 40-pin peripheral port on

a CR1000 or CR3000 datalogger.

This manual describes how to use LoggerNet to connect to your datalogger

with an NL116 attached. You can also use other software packages such as

PC400, RTDAQ, or LoggerLink Mobile Apps for iOS and Android.

Campbell Scientific recommends that only CF cards that have passed our

testing be used with the NL116. For more information on CF cards, see

Campbell Scientific’s application note CF Card Information (3SM-F). Note

that it is not necessary to purchase the CF cards directly from Campbell

Scientific as long as the manufacturer and model number match those shown in

the application note.

Before using the NL116, please study:

• Section 2, Cautionary Statements

(p. 1)

• Section 3, Initial Inspection

(p. 2)

• Section 4, Quickstart

(p. 2)

The Quickstart section explains how to quickly begin using an NL116 for

straightforward Ethernet communications and data-storage operations. The

remainder of the manual is a technical reference which describes in detail such

operations as: IP functionality, file formats, datalogger programming, and data

retrieval.

2. Cautionary Statements

• READ AND UNDERSTAND the Precautions section at the front of this

manual.

• The NL116 requires CR1000 or CR3000 operating system version 28 or

later.

• The first time an NL116 is attached to a datalogger, the datalogger’s

memory has to be reorganized to allow room in memory for the IP stack.

To avoid the loss of data, collect your data before attaching the NL116 to a

datalogger.

• The NL116 is rugged, but it should be handled as a precision scientific

instrument.

NL116 Ethernet and CompactFlash

Module

• The NL116 has integrated surge protection. In order for the surge

protection to work correctly, the NL116 must be well grounded. The

NL116 is grounded through the datalogger’s ground lug via the thumb

screw used to attach the NL116 to the datalogger. That connection is only

made if the thumb screw on the NL116 is tightened down to the

datalogger.

• Shielded Ethernet cable should be used for cable lengths longer than 9 ft.

• Always power down the datalogger before installing to or removing the

NL116 from the datalogger.

3. Initial Inspection

Upon receipt of the NL116, inspect the packaging and contents for damage.

File damage claims with the shipping company.

4. Quickstart

This section describes the basics of communicating via Ethernet and storing

and retrieving datalogger data. These operations are discussed in detail in

Section 7, Operation

(p. 12).

4.1 Physical Setup

Always collect your data before attaching the NL116.

Always power down the datalogger before installing to or

removing the NL116 from the datalogger.

After powering down the datalogger, plug the NL116 into the datalogger

peripheral port (see FIGURE 4-1). Attach Ethernet cable to the Ethernet port.

Restore power to the datalogger. Insert formatted CF card. (For instructions

on formatting a CF card, see Appendix A, CF Card Maintenance

(p. A-1).)

A CF card does not need to be present in order to use the NL116’s

IP functionality.

FIGURE 4-1. NL116 attached to a CR1000

CAUTION

NOTE

NL116 Ethernet and CompactFlash

Module

4.2 Communicating via Ethernet

4.2.1 Step 1: Configure Datalogger

a. Connect serial cable from PC COM port to the datalogger RS-232 port.

b. Open Campbell Scientific’s Device Configuration Utility (DevConfig).

Select the Device Type of the datalogger (CR1000 or CR3000), the

appropriate Communication Port, and Baud Rate. Connect to the

datalogger.

c. Under the TCP/IP tab, input the IP Address, Subnet Mask, and IP

Gateway. These values should be provided by your network

administrator.

Alternatively, note the Eth IP address assigned to the datalogger via

DHCP. However, note that this address is not static and may change.

FIGURE 4-2. DevConfig setup

d. Press the Apply button to save the changes and then close DevConfig.

A temporary IP address may be obtained from a DHCP server.

For more information, see Section 7.1.8, DHCP (p. 19).

NOTE

NL116 Ethernet and CompactFlash

Module

The NL116 must be connected to the datalogger before

configuring the datalogger with DevConfig. If it is not connected,

the TCP/IP settings will not be displayed.

4.2.2 Step 2: LoggerNet Setup

The next step is to run LoggerNet and configure it to connect to the datalogger

via the Ethernet port.

a. In the EZ View of the LoggerNet Setup screen, press Add. Press Next to

advance to the Datalogger Type and Name screen. Select your

datalogger type and press Next.

FIGURE 4-3. Setup screen (EZ View) Datalogger Type

NOTE

NL116 Ethernet and CompactFlash

Module

b. Select IP Port and press Next.

FIGURE 4-4. Setup screen (EZ View) Connection Type

NL116 Ethernet and CompactFlash

Module

c. Input the datalogger’s IP address and port number and press Next. The IP

address and port number are input on the same line separated by a colon.

IPv6 addresses will need to be enclosed in square brackets. An IPv4

address may look like 192.168.1.100:6785. An IPv6 address may look

like [2001:db8::1234:5678]:6785. (The datalogger default port number is

6785. It can be changed using DevConfig.)

FIGURE 4-5. Setup screen (EZ View) IP Port Settings

NL116 Ethernet and CompactFlash

Module

d. Input the PakBus Address of the datalogger.

FIGURE 4-6. Setup screen (EZ View) Datalogger Settings

e. Press Next until you reach the Communication Setup Summary screen.

Press Finish to complete the setup.

4.2.3 Step 3: Connect

You are now ready to connect to your datalogger using the LoggerNet Connect

screen.

Datalogger program transfer, table-data display, and data collection are now

possible.

4.3 Programming the Datalogger to Save Data to the

CompactFlash

Card

The CardOut() instruction is used in the datalogger program to send data to

the CF card. CardOut() must be entered within each DataTable declaration

that is to store data on the CF card. The file is saved on the card with the name

stationname.tablename and a .DAT extension.

The CardOut() instruction has the following parameters:

StopRing: A constant is entered for the StopRing parameter to specify whether

the DataTable created should be a ring-mode table (0) or a fill-and-stop table

(1).

NL116 Ethernet and CompactFlash

Module

Size: A constant is entered in the Size to define the size of the DataTable on

the Card. Size can be defined as a fixed number of records, as auto-allocate, or

as the size of the datalogger memory.

To set the table size to a fixed number of records, enter that value. Enter a –1

to set the size to auto-allocate. If set to auto-allocate, all memory that remains

after creating fixed-sized tables will be allocated to this table. If multiple data

tables are declared with a –1 for size, the available memory will be divided

among the tables. The datalogger attempts to allocate memory to the tables so

that all tables are filled at the same time. Enter –1000 to set the size of the

table on the card to the size of the table in the datalogger’s memory.

In the following example, the minimum batt_volt and a sample of PTemp are

written to the card each time the data table is called. The StopRing parameter

is 0 for ring mode. This means that once the data table is full, new data will

begin overwriting old data. The size parameter is –1, so all available space on

the card will be allocated to the table.

DataTable(Table1,1,-1)

CardOut(0 ,-1)

Minimum(1,batt_volt,FP2,0,False)

Sample(1,PTemp,IEEE4)

EndTable

To prevent losing data, collect data from the CF card before

sending the datalogger a new or modified program. When

a program is sent to the datalogger using the Send button in

the Connect screen of LoggerNet or PC400, an attribute is

sent along with the program that commands the datalogger

to erase all data on the CF card from the currently-running

program.

For other methods of saving data to the CF card, see the TableFile() instruction

in the CRBasic Editor help.

4.4 CF Card Data Retrieval

Data stored on cards can be retrieved through a communication link to the

datalogger or by removing the card and carrying it to a computer with a CF

adapter. With large files, transferring the CF card to a computer may be faster

than collecting the data over a communication link. CF card-data retrieval is

discussed in detail in Section 7.4, CF Card Data-Retrieval Details

(p. 26).

Removing a card while it is active can cause garbled data

and can actually damage the card. Always press the

Initiate Removal button and wait for a green light before

removing card.

CAUTION

NL116 Ethernet and CompactFlash

Module

LoggerNet File Control should not be used to retrieve an

open file (for example, a file created using CardOut or the

latest file created by TableFile, option 64) from a CF card.

Using File Control to retrieve the data can result in a

corrupted data file. However, File Control can be used to

retrieve closed files such as JPEG images or files (other

than the latest) created by TableFile, option 64.

5. Overview

FIGURE 5-1. NL116 Ethernet/CompactFlash

Module

The NL116 Ethernet/CompactFlash

Module enables Ethernet communication

with the datalogger. It also has a slot for a Type I or Type II CompactFlash

(CF) card (3.3 V, 75 mA).

The NL116/CF card combination can be used to expand the datalogger

memory, transport data/programs from the field site(s) to the office, upload

power-up functions, and store JPEG images from a Campbell Scientific

camera. Data stored on cards can be retrieved through a communications link

to the datalogger or by removing the card and carrying it to a computer. The

computer can read the CF card either with the CF1 adapter or 17752

reader/writer. The CF1 adapter allows the PC’s PCMCIA card slot to read the

CF card; the 17752 reader/writer allows the PC’s USB port to read the CF card.

User-supplied CF adapters may also be used.

LoggerNet File Control should not be used to retrieve an

open file (for example, a file created using CardOut or the

latest file created by TableFile, option 64) from a CF card.

Using File Control to retrieve the data can result in a

corrupted data file. However, File Control can be used to

retrieve closed files such as JPEG images or files (other

than the latest) created by TableFile, option 64.

CAUTION

NL116 Ethernet and CompactFlash

Module

5.1 Buttons and Status LED

There is one red-green-orange LED (light-emitting diode) and two buttons:

Initiate Removal and eject. The Status LED indicates the status of the

module. The LED will flash red when the CF card is being accessed, solid

green when it is OK to remove the card, solid orange to indicate an error, and

flashing orange if the card has been removed and has been out long enough that

CPU memory has wrapped and data is being overwritten without being stored

to the card. The Initiate Removal button must be pressed before removing a

card to allow the datalogger to store any buffered data to the card and then

power off. The eject button is used to eject the CF card. Note that if the eject

button cannot be pressed, it may have been disabled by bending it to the right.

Straighten and press the eject button to eject the CF card.

5.2 Power

The Ethernet/CompactFlash

module is powered by 12 Vdc received from the

datalogger through the peripheral port.

Additional power consumption occurs if the Status LED is continuously lit.

At 12 Vdc, an additional 1 mA is drawn by the red or green LED; an additional

2 mA is drawn by the orange LED.

5.3 CF Card Data Retention

The module accepts CF cards which do not require power to retain data.

Typically, a CF card can be erased and rewritten a minimum of 100,000 times.

Industrial CF cards, graded for 2,000,000 write cycles, are recommended for

most applications.

6. Specifications

Datalogger Compatibility: CR1000, CR3000 (both require OS

version 28 or later)

Storage Capacity: Depends on card size

Maximum individual file size is 2 GB

Power Requirements: 12 V supplied through datalogger’s

peripheral port

Current Drain: 64 mA w/Ethernet Active @ 10 Mb

58 mA w/Ethernet Active @ 100 Mb

3 mA w/Ethernet Not Active, CF Card Only

Note: Ethernet can be put into a low-

power state (not connected to the network,

essentially off) using the IPNetPower() or

EthernetPower() instruction.

Operating Temperature Range: –40 to 70 °C Standard

–55 to 85 °C Extended

NL116 Ethernet and CompactFlash

Module

Compliance Information: Application of Council Directive(s):

2004/108/EC Electromagnetic

Compatibility Directive (EMC)

Product Standard: EN 61326-1:2013 –

Electrical Equipment for measurement,

control and laboratory use – EMC

requirements – for use in industrial

locations.

2011/65/EU The Restriction of Hazardous

Substances Directive (RoHS2)

Cable Requirements: Use a straight-through Ethernet cable

when the cable is run from the hub to the

NL116. Use a shielded cable when the

cable length is more than 9 ft.

Note: The maximum recommended

segment length for 10BaseT and

100BaseTx networks using CAT5 cable is

100 meters. Segment length is the length

of cable between the NL device and the

Ethernet repeater, hub, switch, or router it

is connected to.

CF Card Requirements: Industrial grade

Ethernet Speed: 10/100 Mbps (10Base-T / 100Base-Tx),

full and half duplex, all auto-negotiated.

Typical access speeds vary and range from

20 KBytes/sec to 200 KBytes/sec

depending on multiple factors (*** see

note).

Memory Configuration: User-selectable for either ring style

(default) or fill-and-stop.

Dimensions: 10.2 x 8.9 x 6.4 cm (4.0 x 3.5 x 2.5 in)

Weight: 154 g (5.4 oz)

*** The NL116 will automatically negotiate the speed and duplex mode used for the

Ethernet link. However, the speed at which data can be transferred to and from a

datalogger over the NL116 depends on multiple factors including:

• the datalogger processor speed, that is, CR1000 vs CR3000

• how busy the datalogger is performing measurement, processing, control and

other communication tasks; measurement tasks take priority over

communication tasks

• the IP protocol used for the data transfer and how/if the link is encrypted

• where the data is being transferred from or to, for example, USR vs CRD

• limitation of the IP connection due to congestion, the number of “hops”, and

the quality of the physical media between the client and host

Below are some example data transfer rates observed over an ideal connection. A

laptop computer was connected directly to the NL116 interface, transferring a 1.7 MB

file to and from the datalogger USR drive.

NL116 Ethernet and CompactFlash

Module

CR1000

(Sending from computer to datalogger; retrieving from datalogger to computer)

• PakBus: 30 KBytes/sec; 30 KBytes/sec

• FTP/HTTP: 55 Bytes/sec; 90 KBytes/sec

CR3000

(Sending from computer to datalogger; retrieving from datalogger to computer)

• PakBus: 65 KBytes/sec; 65 KBytes/sec

• FTP/HTTP: 135 KBytes/sec; 210 KBytes/sec

7. Operation

7.1 TCP/IP Functionality

This section describes the main TCP/IP functionality of a datalogger with an

NL116 attached. Additional functionality may be added in the future. For

more information, refer to the Information Services section of the datalogger

manual and CRBasic Editor help.

7.1.1 Communicating Over TCP/IP

Once the datalogger, the NL116, and LoggerNet have been set up as described

in Sections 4.1, Physical Setup

(p. 2), and 4.2, Communicating via Ethernet (p. 3),

communication is possible over TCP/IP. This includes program send and data

collection. These are straightforward operations and are accomplished through

the LoggerNet Connect screen. For more information, see the LoggerNet

manual.

Data callback and datalogger-to-datalogger communications are also possible

over TCP/IP, as well as the creation of simple HTML pages to view datalogger

variables using a web browser.

7.1.1.1 Data Callback

The following program is an example of doing data callback over TCP/IP. It

first checks to see if a port to the LoggerNet server already exists. (The

LoggerNet server is assumed to be at the default PakBus address, 4094.) If not,

a socket to LoggerNet is opened using the TCPOpen() instruction. The

SendVariables() instruction is then used to send data.

Page is loading ...

Campbell Scientific NL116 Owner's manual

Brand: Campbell Scientific

Model: NL116

Category: Measuring, testing & control

Type: Owner's manual

This manual is also suitable for

NL116 and CompactFlash

Download PDF

report

Campbell Scientific NL116 Owner's manual

This manual is also suitable for

Campbell Scientific NL116 Owner's manual

Related papers

Other documents