Dwyer Series GSTA User manual

Series GSTA
Dwyer
Brand
Dwyer
Model
Series GSTA
Type
User manual

This manual is also suitable for

Dwyer Series GSTA stand-alone carbon monoxide detectors provide relay contacts to control fan or damper operation directly without a BMS controller. Ideal for smaller garages or service stations, these detectors feature a set point and high gas concentration alarm, with Modbus RS-485 serial communications for feedback to a building management system. For energy savings, PID capabilities can be used to drive a VFD for better ventilation control. Expandable with pluggable slave modules, the GSTA can be used with multiple carbon monoxide sensor loops.

Dwyer Series GSTA stand-alone carbon monoxide detectors provide relay contacts to control fan or damper operation directly without a BMS controller. Ideal for smaller garages or service stations, these detectors feature a set point and high gas concentration alarm, with Modbus RS-485 serial communications for feedback to a building management system. For energy savings, PID capabilities can be used to drive a VFD for better ventilation control. Expandable with pluggable slave modules, the GSTA can be used with multiple carbon monoxide sensor loops.

Stand Alone Carbon Monoxide Detectors
Application and Installation Note
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]
W
hile many parking garage applications require a carbon monoxide transmitter
w
ith a current or voltage signal to feed a BMS controller, there are applications for
s
maller garages or service stations for the carbon monoxide sensor to provide
relay contacts to control the fan or damper operation directly without the BMS
Controller. These systems are considered stand alone systems. The Dwyer GSTA
series and CMT200 series transmitters can meet the need of the applications that
just require a current or voltage output. For stand alone systems, these transmitters
c
an be combined with a SCD series process controller.
T
he SCD series controller accepts the signal input from the carbon monoxide
transmitter and allows the user to adjust the set point and differentials for the fan /
damper operation (typically around 25 PPM). In addition to the set point, the user
can also set a high gas concentration alarm (normally set around 100 PPM). For
systems that need to communicate with a building management system or other
online management system, the SCD series has Modbus
®
RS-485 serial
communications as a standard offering to give feedback of the current gas
concentration, set points, and output status.
For additional energy savings, the SCD series controller has PID capabilities that
can be used to drive a VFD to have better ventilation control. Both the transmitters
and the SCD can be powered using a common 24 VDC power supply such as our
model SCD-PS. For applications that require additional sensors, pluggable slave
modules are available that allow the controller to be expanded to have multiple
carbon monoxide sensor loops.
Programming Guide for the SCD Series
All programming will be configured either at the factory or using the
communications port. For the communication port, programmer will need a model
MN-1 RS-485 to USB converter, laptop, and SCD-SW configuration software.
S
ERIES SCD PARAMETER SETTINGS
INITIAL SETTING PARAMETERS
Input: 4 to 20 mA.
Units: None.
S
cale High: 200.
S
cale Low: 0.
C
ontrol Mode: On-Off (PID if using with VFD).
Heat/Cool Selection: Cool.
Alarm 1 Type: 11-high alarm with hysteresis.
Communication Data: Set to match BMS settings.
OPERATING SETTING PARAMETERS
Set Point: 25 (or different PPM value depending on local requirements)
Alarm 1 Set Point: 100 (or different PPM value depending on local requirements)
REGULATION SETTING PARAMETERS
Cooling Hysteresis (Differential): 5 (or different PPM setting depending on local
code)
Process Input Offset: Only if there is any adjustment required due to sensor drift
or error due wire resistance.
S
eries GSTA
S
eries SCD
Modbus
®
is a registered trademark of Schneider Automation, Inc.
DWYER INSTRUMENTS, INC.
Phone: 219/879-8000 www.dwyer-inst.com
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46360, U.S.A. Fax: 219/872-9057 e-mail: [email protected]
SCD-PS
P
OWER SUPPLY
BOTTOM
V
IEW OF
SCD-1033
SCD-1033
SCD-2033
SCD-2033
TO BMS
C
ONTROLLER
RS-485 MODBUS
FAN/DAMPER
M
OTOR CONTROL
T
O STROBE
LIGHT/BUZZER
GSTAGSTAGSTA
S
ample Wiring Diagram for 3 Carbon Monoxide Loops
  • Page 1 1
  • Page 2 2

Dwyer Series GSTA User manual

Series GSTA
Dwyer
Brand
Dwyer
Model
Series GSTA
Type
User manual
This manual is also suitable for

Dwyer Series GSTA stand-alone carbon monoxide detectors provide relay contacts to control fan or damper operation directly without a BMS controller. Ideal for smaller garages or service stations, these detectors feature a set point and high gas concentration alarm, with Modbus RS-485 serial communications for feedback to a building management system. For energy savings, PID capabilities can be used to drive a VFD for better ventilation control. Expandable with pluggable slave modules, the GSTA can be used with multiple carbon monoxide sensor loops.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents