ADDER ALIF1000 Quick start guide

ADDER
Brand
ADDER
Model
ALIF1000
Type
Quick start guide

This manual is also suitable for

AdderLink Infinity
Quick Start Guide
ALIF 1000 and 2000 (transmitter and receiver) - front panel indicators
NET SER AUD USB DVIPWR
The six indicators on TX and RX units clearly show the key aspects of operation:
• NET On when valid network link is present.
Flashes if there’s an error.
• SER On when the serial port is enabled and active.
• AUD On when audio is enabled and active.
• USB On when USB is enabled and active.
• DVI On when DVI video is enabled and active.
• PWR Power indicator.
ALIF1000
ALIF2000
{
CONNECTIONS KEY
Direct Gigabit Ethernet link
Switched Gigabit Ethernet link
Direct Fibre Optic link
Switched Fibre Optic link
www.adder.com
AdderLink
RECEIVER
NETSER AUD USB DV I PWR
www.adder.com
AdderLink
NET SERAUD USBDVI PWR
T RANSMIT
Gigabit
Ethernet
Network
ALIF1000
www.adder.com
AdderLink
NET SERAUD USBDVI PWR
TRANSMIT
www.adder.com
AdderLink
NET SER AUDUSB DVI PWR
RECEIVER
Gigabit
Ethernet
Network
Fibre
Optic
Network
OR
ALIF2000
Second port
reserved
Configuration
• IfALIFTXandRXunitsaredirectlyconnected,noconguration
actionisrequired,providedthattheyhavetheirfactorydefault
settingsinplace.Ifthestandardsettingshavebeenchangedina
previousinstallation,youmerelyneedtoperformafactoryreset
on each unit (see below).
• WhereALIFunitsareconnectedvianetworklinks,youwillneed
to specify their network address details. This can be done by
connectingacomputersystemtemporarilytoeachALIFunit
andusingtheInnitybrowser-basedcongurationutility.This
congurationutilityalsoallowsnumerousothersettingstobe
altered.
Note: For basic one-to-one installations, the factory default
addresses may be acceptable for immediate use within your
network without the need to use a configuration utility or change
their values: TX unit (169.254.1.33), RX unit (169.254.1.32).
Manual factory reset
UsetoreturnaTXorRXunittoitsdefaultconguration.
1 RemovepowerfromtheALIFunit.
2 Locatethesmallholeonthefrontpanel:ALIF1000-Nexttothe
onlyEthernetsocket;ALIF2000-Nexttotheleft-handEthernet
socket.
3 Pushanarrowimplement(e.g.astraightened-outpaperclip)into
theholeandholditin.Meanwhile,powerontheunit.
Afteraroundeightseconds,whenthefactoryresethas
completed,veofthefrontpanelindicatorswillashforaperiod
of three seconds to indicate a successful reset operation.
4 Removetheimplementandthenre-applypowertostarttheunit
initsdefaultconguration.
A Power input
B Congswitches
E Audiolinein/out
F Serialcongport
C USB port(s)
D Video input
G Video output
INDOOR
USE ONLY
OPTIONS
AUX
LINE IN/
LINE OUT
DVI-D
1 2
USER CONSOLE
5V
2.5A
ON
21
MIC IN
ALIF1000 receiver - rear panel
A
C E
B
F
G
ALIF1000 transmitter - rear panel
AUX
LINE IN
LINE OUT
COMPUTER
ON
21
INDOOR
USE ONLY
OPTIONS
1 2
5V
2.5A
DVI-D
A
C
D
E
B
F
AUX
COMPUTER
ON
21
INDOOR
USE ONLY
OPTIONS
1 2
DVI-D-1
5V 2.5A
DVI-D-2
IN OUT
A
C
D
E
B
F
ALIF2000 transmitter - rear panel
D
1
2
DVI-D-2
5V 4A
DVI-D-1
ALIF2000 receiver - rear panel
A
C
G
E
B
F
G
1
2
Note:
ALIF1000
units use
12.5W
power
adapters.
Note:
ALIF2000
units use
20W
power
adapters.
Infinity browser-based configuration utility
Tousethebrowser-basedcongurationutility,linkacomputervia
anetworkswitchtotheALIFunit(GigabitEthernetisnotessential
forthecongurationstage).Thiscongurationutilityallowsyouto
performallofthefollowingfunctions:
• View/edittheIPnetworkaddressandnetmask,
• CongureseparateIPnetworkaddressesforvideo,audioandUSB,
• Conguremulticastsettings(onRXunits),
• Congurevideobandwidthsettings(onTXunits),
• Viewthecurrentvideooutput(onTXunits),
• Performarmwareupgrade,
• Performafactoryreset.
To access the browser-based configuration utility
1 ConnecttheInnityunitandacomputerviaanetwork.
2 RunawebbrowseronyourcomputerandentertheIPaddressof
theInnityunit,e.g.http://169.254.1.33 or http://169.254.1.33
Thedefaultsettingsareasfollows:
• TX units-IPaddress:169.254.1.33Netmask:255.255.255.0
• RX units-IPaddress:169.254.1.32Netmask:255.255.255.0
Note: Where the address of a unit is not known, perform a
manual factory reset (see left) to restore the default address.
TX (transmitter) unit configuration
IntheALIFsystem,themostimportantcongurationdetailsare
dictatedbyRXunits.Thus,theTXunitsetupisconcernedonlywith
threemainfactors:
• ItsIPaddress,
• Thedatastreamstoenable/disable,and
• Videosignaloptimization.
ThemethodtosettheIPaddressanddatastreamsisexactlythe
sameasfortheRXunit-pleasefollowsteps1to3ofConfiguring
the RX unitsectionontherearpage.InaGigabitEthernetnetwork
withsufcientbandwidth,changestotheVideo Configurationpage
shouldnotbenecessary.Ifadjustmentsarerequired,pleaseseethe
AdderLinkInnityfulluserguidefordetails.
RX (receiver) unit configuration
Pleaseseetherearpage.
AdderTechnologyLimited,
SaxonWay,BarHill,
Cambridge,CB238SL,
UnitedKingdom
Tel:+44(0)1954780044
Fax:+44(0)1954780081
[email protected]
www.adder.com
©2011AdderTechnologyLimited•Release1.1b
Alltrademarksareacknowledged.MAN-ALIF-QUICK
AdderCorporation,
350RMerrimacStreet,
Newburyport,
MA01950,
UnitedStatesofAmerica
Tel:+1-888-932-3337
Fax:+1-888-275-1117
AdderAsiaPacic,
8BurnRoad,
#04-10,Trivex,
369977,Singapore
Tel:+6562885767
Fax:+6596161283
IMPORTANT:PleaseseethefullInnityuser
guideforsafety,warrantyandregulatory
information.Thefulluserguideissupplied
ontheCD-ROMwiththeunitandisalso
availablefromwww.adder.com.
RX (receiver) unit configuration
IntheALIFsystem,theRXunitdetermineswhereandhowdata
signalsaresent(andreceived)bytheTXunit.Althoughnumerous
ALIFtopologies(one-to-one,one-to-many,many-to-one,etc.)are
madepossible,theyarealldependentontwounderlyingmodesof
operation: either Unicast or Multicasttransmission.Wheremulticast
transmissionisnotinvokedforvideoand/oraudiodata,operation
willbeautomaticallyservedbyunicastnetworktransmission
technologies.
Configuring the RX unit
1 Display the System ConfigurationpageoftheInnitybrowser-
basedcongurationutility.
2 EnsurethattheIPaddressandnetmaskforthisRXunitarecorrect.
TheSystemIPAddresssetherewillbesenttotheTXunitasthe
destinationfortransmitteddata(wheninunicastmode).
3 Checkthatthedatastreams(VideoTX,AudioTX/RXandUSB
TX/RX)areenabled(ticked)ordisabled(unticked)asappropriate.
TherearesimilaroptionswithintheInnityTXunitconguration
anditisimportantthatthesettingsinbothunitsarethesame.
4 IntheRemoteUnitSettingssection,entertheIPaddressforthe
TXunitthatwillbesupplyingthevideo,audioandUSBdata
streams.Mostoftenallthreestreamsaresuppliedbythesame
TXunit,however,itispossibletoreceivethemfromdifferent
locations (click the blue arrow to reveal the separate addresses).
5 ForinstallationsthatwillincludemorethanoneRXunit,youalso
needtoconguretheMulticast Settings section.
TheVideoandAudiosectionsareconguredinthesameway:
• TicktheEnableMulticastVideo/EnableMulticastAudiobox.
• Next,enteranappropriateMulticastAddressfortheVideo/
Audiodatastream(s).TheIPaddressesbetween224.0.0.0
and239.255.255.255arespecicallyreservedbynetworksfor
multicastoperations.
The address that you enter will be used by the RX unit to
‘listen-in’onthedatastreamfromtheTXunit.ThissameIP
addressneedstobesetoneveryRXunitthatwillsimilarly
receivethedatastream.Thevideoandaudiomulticast
addressescanbethesameordifferent,asrequired.
• ClicktheUpdateNowbuttontosave.
RepeattheIPaddressingandmulticastcongurationstepsforall
RXunitsthatwillbepartoftheone-to-manyinstallation.
Formostinstallations,thesuccessfulimplementationofthese
congurationstepswillresultinacorrectlyworkingsystem.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ADDER ALIF1000 Quick start guide

ADDER
Brand
ADDER
Model
ALIF1000
Type
Quick start guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents