Gigabyte GA-7TEWH1 User manual

Brand: Gigabyte

Model: GA-7TEWH1

Category: Motherboards

Type: User manual

USER’S Manual

GA-7TEWH

Dual Xeon Processor Motherboard

Xeon

Processor Motherboard

Rev. 1001

* The WEEE marking on the product indicates this product must not be disposed of with

user's other household waste and must be handed over to a designated collection point

for the recycling of waste electrical and electronic equipment!!

* The WEEE marking applies only in European Union's member states.

English

Table of Content

Table of Contents

Item Checklist ........................................................................................4

Chapter 1 Introduction............................................................................5

1.1. Considerations Prior to Installation ......................................................5

1.2. Features Summary............................................................................... 6

1.3. GA-7TEWH Motherboard Component ................................................8

Chapter 2 Hardware Installation Process............................................. 11

2.1.Installing Processor and CPU Haet Sink ............................................ 11

2.1.1. Installing CPU ........................................................................................................11

2.1.2. Installing Heat Sink ............................................................................................... 12

2.2. Installing memory modules ................................................................13

2.3. Connect ribbon cables, cabinet wires, and power supply.................17

2.3.1. I/O Back Panel Introduction ................................................................................. 17

2.4. Connectors Introduction.....................................................................20

2.5. Jumper Setting....................................................................................29

Chapter 3 BIOS Setup .........................................................................31

Main...........................................................................................................33

Advanced ...................................................................................................34

Processor Configuration.................................................................................................. 35

Power Management........................................................................................................ 39

Memory Configuration..................................................................................................... 42

Advanced Chipset Configuration ................................................................................... 44

PCI Configuration............................................................................................................. 48

SATA Configuration.......................................................................................................... 50

I/O DeviceConfiguration .................................................................................................. 52

Boot DeviceConfiguration................................................................................................ 54

Haradware Monitor .......................................................................................................... 56

Power.........................................................................................................57

Security ......................................................................................................59

Server.........................................................................................................61

English

GA-7TEWH Motherboard

System Management...................................................................................................... 62

Console Redirection........................................................................................................ 63

Boot............................................................................................................65

Exit .............................................................................................................66

Introduction

 The GA-7TEWH motherboard

 Serial ATA cable x 6

 I/O Shield Kit

 CD for motherboard driver & utility

 GA-7TEWH quick reference guide

Item Checklist

* The items listed above are for reference only, and are subject to change without notice.

English

GA-7TEWH Motherboard

Chapter 1 Introduction

1.1. Considerations Prior to Installation

Preparing Your Computer

The motherboard contains numerous delicate electronic circuits and components which can become

damaged as a result of electrostatic discharge (ESD). Thus, prior to installation, please follow the

instructions below:

1. Please turn off the computer and unplug its power cord.

2. When handling the motherboard, avoid touching any metal leads or connectors.

3. It is best to wear an electrostatic discharge (ESD) cuff when handling electronic components

(CPU, RAM).

4. Prior to installing the electronic components, please have these items on top of an antistatic pad or

within a electrostatic shielding container.

5. Please verify that the power supply is switched off before unplugging the power supply connector

from the motherboard.

Installation Notices

1. Prior to installation, please do not remove the stickers on the motherboard. These stickers are

required for warranty validation.

2. Prior to the installation of the motherboard or any hardware, please first carefully read the

information in the provided manual.

3. Before using the product, please verify that all cables and power connectors are connected.

4. To prevent damage to the motherboard, please do not allow screws to come in contact with the

motherboard circuit or its components.

5. Please make sure there are no leftover screws or metal components placed on the motherboard

or within the computer casing.

6. Please do not place the computer system on an uneven surface.

7. Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

8. If you are uncertain about any installation steps or have a problem related to the use of the product,

please consult a certified computer technician.

Instances of Non-Warranty

1. Damage due to natural disaster, accident or human cause.

2. Damage as a result of violating the conditions recommended in the user manual.

3. Damage due to improper installation.

4. Damage due to use of uncertified components.

5. Damage due to use exceeding the permitted parameters.

6. Product determined to be an unofficial Gigabyte product.

Introduction

1.2. Features Summary

Form Factor  12” x 13” EATX size form factor, 8 layers PCB

CPU  Supports Dual Intel

Xeon

Nehalem-EP 2S processors

 Xeon

Quad Core in LGA 1366 socket

 Supports QuickPath Interconnect up to 6.4GT/s

 Enhanced Intel SpeedStep Technology (EIST) & Demand Based

Switch (DBS)

 Support Intel Virtualization Technology (VT)

Chipset  Intel

5520 (Tylersburg-36D) Chipset

 Intel

82801JR (ICH10R)

Memory  12 x 1.5V DDR3 DIMM sockets supporting up to 96 GB

of system memory

 3 channel memory architecture

 Support 800/1066/1333 memory

 Support ECC RDIMM/ UDIMM

I/O Control  ITE IT8720F Super I/O

Expansion Slots  1 PCI slots 32-Bit/33MHz (5V)

 1 PCI-E x16 slot (Gen2 x16 bandwidth)

 1 PCI-Express x8 slots (Gen2 at x8 bandwidth)

 1 PCI-Express x8 slots (Gen2 at x4 bandwidth)

 1 PCI-Express x8 slots (Gen 1 at x4 bandwidth)

 1 SO-DIMM for add-on SAS RAID card (optional device)

SATA RAID Controller  Intel

ICH10R SATA Controller

 Supports 6 independant SATA 3.0 Gb/s with Software RAID 0,1,

5,10

On-Board Audio  Realtek

ALC889A HD Audio Codec

IEEE1394A  TI TSB43AB23

On-Board LAN  Intel

82567LM and 82574L GbE controllers support Gigabit

Ethernet ports

 Supports QuickData DMA engine/TCP acceleration/IA-optimized

TCP stack/DCA( Direct Cache Access)/LLI, MSI-X,RSS

Internal Connector  2 x 8-pin ATX power connector

 1 x 24-pin ATX power connector

 6 x SATA 3.0Gb/s connectors

 1 x Serial connector (COM)

 1 x Audio connector

 1 x IEEE 1394 connector

English

GA-7TEWH Motherboard

 1 x USB 2.0 connector for additional 2 ports by cable

 1 x front panel connecctor

 1 x PSMI connecctor

 6 x System fan cable connector

 2 x CPU fan cable connectors

Rear Panel I/O  P/S 2 Keyboard and Mouse Connectors

 1 x Serial port

 1 x Parallel port supports Normal/EPP/ECP mode

 1 x IEEE 1394 port

 4 x USB 2.0 dual-port connector

 2 x RJ45 LAN ports

 6 x Audio ports (4 x Line-out/ 1 x Line-in/ 1 x MIC)

Hardware Monitor  Winbond 83792G controller

 Enhanced features with CPU Vcore, 1.5V reference,

VCC3 (3.3V) , VBAT3V, +5VSB, CPUA/B Temperature, and

System Temperature Values viewing

 CPU/Power/System Fan Revolution Detect

 CPU shutdown when overheat

 System Voltage Detect

 Support basic ASF remote transaction through CSA Bus with

hardware circuit

BIOS  Phoenix BIOS on 16Mb flash RAM

Additional Features  Supports S4, S5 under Windows Operating System

 Wake on LAN (WOL)

 Wake on Ring (WOR)

 AC Recovery

 Supports Console Redirection

 Supports 4-pin Fan controller

Introduction

1.3. GA-7TEWH Motherboard Component

No Code Description

1. CPU1 Primary CPU

2. CPU2 Secondary CPU

3. U82 Intel Tylersburg-36D IOH

4. U60 Intel ICH10R

5. U188 Winbond W83792G

6. U208 Intel 82567LM GbE

7. U207 Intel 82574L GbE

8. AU1 Realtek ALC 889A

9. U210 TSB43AB23 1394 chipset

10. U34 BMC Flash ROM

11. COM2 COM2 connector

12. F_1394 Front 1394 connector

13. AUDIO_ACZ1 Front Audio connector

14. SPDIF_JP1 SPDIF JP1 jumper

15. BAT CMOS battery

16. CASE_OPEN Case open intrusion

17. F_PANEL1 Front panel connector

18. PCI-E1 PCI-E x16 slo t

(Gen2 at x16 bandwidth)

19. PCI-E2 PCI-E x8 slot (Gen2 at x8 bandwidth)

20. PCI-E3 PCI-E x8 slot (Gen2 at x4 bandwidth)

21. PCI-E4 PCI-E x8 slot (Gen1 at x4 bandwidth)

22. PCI5 PCI 32bit/33MHz slot

23. PCIE_SODIM SO-DIMM for SAS RAID card

24. J3 SMBus connector for B/P board

25. SATA5 SATA5 data cable connector

26. SATA4 SATA4 data cable connector

27. SATA3 SATA3 data cable connector

28. SATA2 SATA2 data cable connector

29. SATA1 SATA1 data cable connector

30. SATA0 SATA0 data cable connector

31. USB1 Front USB connector

32. SGPIO_ JP1 SGPIO JP1 jumper

33. SGPIO_ JP2 SGPIO JP2 jumper

34. PSMI SMBUS connector for power supply

35. FAN_CPU1 CPU1 fan cable connector

36. FAN_CPU2 CPU2 fan cable connector

English

GA-7TEWH Motherboard

No Code Description

37. FAN_SYS6 System fan 6 cable connector

38. FAN_SYS5 System fan 5 cable connector

39. FAN_SYS4 System fan 4 cable connector

40. FAN_SYS3 System fan 3 cable connector

41. FAN_SYS2 System fan 2 cable connector

42. FAN_SYS1 System fan 1 cable connector

43. DIMMC1 Channel C slot 1 (for primary CPU)

44. DIMMC2 Channel C slot 2 (for primary CPU)

45. DIMMB1 Channel B slot 1 (for primary CPU)

46. DIMMB2 Channel B slot 2 (for primary CPU)

47. DIMMA1 Channel A slot 1 (for primary CPU)

48. DIMMA2 Channel A slot 2 (for primary CPU)

49. DIMMD2 Channel D slot 2 (for secondary CPU)

50. DIMMD1 Channel D slot 1 (for secondary CPU)

51. DIMME2 Channel E slot 2 (for secondary CPU)

52. DIMME1 Channel E slot 1 (for secondary CPU)

53. DIMMF2 Channel F slot 2 (for secondary CPU)

54. DIMMF1 Channel F slot 1 (for secondary CPU)

55. KB_MS PS/2 Keyboard/Mouse ports

56. COMA Serial port

57. LPT1 Parallel port

58. 1394_1 1394a port

59. GLAN1 Gigabit LAN port and USB ports

60. GLAN2 Gigabit LAN port and USB ports

61. AUDIO1 Audio ports

62. ATX 24-pin Power connector

63. 12V_AUX2 CPU2 8-pin Power connector

64. 12V_AUX1 CPU1 8-pin Power connector

65. CLR_CMOS Clear CMOS jumper

66. CLR_RTC Clear RTC jumper

67. BIOS_RVCR BIOS Recovery jumper

68. PASS_DIS Password Disable jumper

English

GA-7TEWH Motherboard

1314

1819202122

4039

434445464748

495051525354

55565758596061

Hardware Installation Process

Chapter 2 Hardware Installation Process

Before installing the processor and cooling fan, adhere to the following

cautions:

1. The processor will overheat without the heatsink and/or fan, resulting in permanent

irreparable damage.

2. Never force the processor into the socket.

3. Apply thermal grease on the processor before placing cooling fan.

4. Please make sure the CPU type is supported by the motherboard.

5. If you do not match the CPU socket Pin 1 and CPU cut edge well, it will cause

improper installation. Please change the insert orientation.

2.1. Installing Processor and CPU Haet Sink

2.1.1. Installing CPU

Step 1 Raise the metal locking lever on the socket.

Step 2 Remove the plastic covering on the CPU socket.

Step 3 Insert the CPU with the correct orientation. The CPU only fits in one orientation.

Step 4 Once the CPU is properly placed, please replace the metal cover and push the metal

lever back into locked position.

English

GA-7TEWH Motherboard

2.1.2. Installing Heat Sink

Step 1 Attach the heat sink clip to the processor socket.

Step 2 Secure the cooing fan withscrews.

Step 3 Connect processor fan can cable to the processor fanconnector

Hardware Installation Process

2.2. Installing memory modules

Before installing the memory modules, please comply with the following conditions:

1. Please make sure that the memory is supported by the motherboard. It is

recommended to use the memory with similar capacity, specifications and brand.

2. Before installing or removing memory modules, please make sure that the computer

power is switched off to prevent hardware damage.

3. Memory modules have a foolproof insertion design. A memory module can be installed

in only one direction. If you are unable to insert the module, please switch the direction.

The motherboard supports DDR3 memory modules, whereby BIOS will automatically detect memory

capacity and specifications. Memory modules are designed so that they can be inserted only in one

direction. The memory capacity used can differ with each slot.

Memory sockets for Processor 2

Memory sockets for

Processor 1

Hardware Installation Process

Installation Steps:

Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down.

Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.

NOTE! DIMM must be populated in order starting from DIMMA1/D1 socket. For dual-channel

operation, DIMMs must be installed in matched pairs.

Step 3. Reverse the installation steps when you wish to remove the DIMM module.

CPU2

CPU1

DIMMD2

DIMMD1

DIMME2

DIMME1

DIMMF2

DIMMF1

DIMMA2

DIMMA1

DIMMB2

DIMMB1

DIMMC2

DIMMC1

English

GA-7TEWH Motherboard

U-DIMM Population Table

DIMMA1/D1

1GB

Interleave

mode

Single

Channel

Dual

Channel

Three

Channel

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

Channel A Channel B Channel C

Tot al

Memory

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

2GB

4GB

8GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

1GB

2GB

4GB

6GB

12GB

16GB

6GB

3GB

16GB

24GB

English

GA-7TEWH Motherboard

R-DIMM Population Table

Interleave

mode

Single

Channel

Dual

Channel

Three

Channel

Channel A Channel B Channel C

Total

Memory

DIMMA1/D1

1GB

DIMMA2/D2 DIMMB1/E1 DIMMB2/E2 DIMMC1/F1 DIMMC2/F2

2GB

4GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB 1GB

2GB

4GB

8GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

1GB

2GB

4GB

8GB

6GB

12GB

24GB

48GB

8GB

2GB

4GB

8GB

16GB

4GB

8GB

16GB

32GB

3GB

6GB

12GB

24GB

Hardware Installation Process

2.3.1. I/O Back Panel Introduction

2.3. Connect ribbon cables, cabinet wires, and power supply

English

GA-7TEWH Motherboard

PS/2 Keyboard and PS/2 Mouse Connector

To install a PS/2 port keyboard and mouse, plug the mouse to the upper port (green) and the

keyboard to the lower port (purple).

Parallel Port / Serial Port

This connector supports 1 standard 1 Parallel port. Device like printer can be connected to Parallel

port.

Serial Port

Connects to serial-based mouse or data processing devices.

IEEE1394 Port

Serial interface standard set by Institute of Electrical and Electronics Engineers, which has

features with high speed, high bandwidth and hot plug.

Gigabit LAN Ports

The LAN port provides Internet connection of Gigabit Ethernet with data transfer speeds of

10/100/1000Mbps.

USB Port

Before you connect your device(s) into USB connector(s), please make sure your device(s)

such as USB keyboard, mouse, scanner, zip, speaker...etc. have a standard USB interface.

Also make sure your OS supports USB controller. If your OS does not support USB controller,

please contact OS vendor for possible patch or driver updated. For more information please

contact your OS or device(s) vendors.

Line In

The default Line In jack. Devices like CD-ROM, walkman etc. can be connected to Line In jack.

Line Out (Front Speaker Out)

The default Line Out (Front Speaker Out) jack. Stereo speakers, earphone or front surround

speakers can be connected to Line Out (Front Speaker Out) jack.

MIC In

The default MIC In jack. Microphone must be connected to MIC In jack.

Surround Speaker Out (Rear Speaker Out)

The default Surround Speaker Out (Rear Speaker Out) jack. Rear surround speakers can be

connected to Surround Speaker Out (Rear Speaker Out) jack.

Center/Subwoofer Speaker Out

The default Center/Subwoofer Speaker Out jack. Center/Subwoofer speakers can be connected

to Center/Subwoofer Speaker Out jack.

Hardware Installation Process

LAN LED Description

LED1 (Green)

LED2 (Green/Yellow)

Color Condition Description

Green ON LAN Link / no Access

Green BLINK LAN Access

- OFF Idle

- OFF 10Mbps connection

Green BLINK Port identification with 10 Mbps connection

Green ON 100Mbps connection

Green BLINK Port identification with 100Mbps connection

Yellow ON 1Gbps connection

Yellow BLINK Port identification with 1Gbps connection

Name

LED1

LED2

Side Speaker Out

The default Side Speaker Out jack. Surround side speakers can be connected to Side Speaker

Out jack.

English

GA-7TEWH Motherboard

2.4. Connectors Introduction

1. ATX 15. PSMI

2. 12V_AUX1 16. FAN_CPU1 (CPU1 fan cable connector)

3. 12V_AUX2 17. FAN_CPU2 (CPU2 fan cable connector)

4. COM2 18. SYS_FAN1 (System fan connector)

5. USB1 (Front USB cable connector) 19. SYS_FAN2 (System fan connector)

6. F_1394 20. SYS_FAN3 (System fan connector)

7. FAUDIO_ACZ 21. SYS_FAN4 (System fan connector)

8. F_PANEL 22. SYS_FAN5 (System fan connector)

9. SATA0 (SATA data cable connector) 23. SYS_FAN6 (System fan connector)

10. SATA1 (SATA data cable connector) 24. J3

11. SATA2 (SATA data cable connector) 25. SGPIO_JP1

12. SATA3 (SATA data cable connector) 26. SGPIO_JP12

13. SATA4 (SATA data cable connector 27. BAT

14. SATA5 (SATA data cable connector

18192021

Page is loading ...

Gigabyte GA-7TEWH1 User manual

Brand: Gigabyte

Model: GA-7TEWH1

Category: Motherboards

Type: User manual

Download PDF

report

Gigabyte GA-7TEWH1 User manual

Gigabyte GA-7TEWH1 User manual

Related papers

Other documents