Husky 33144 User manual

Brand: Husky

Model: 33144

Type: User manual

2TIERWDHITCHDISPLAYSTAND

01/15/18_REV2

PART#33144

Toolsrequired:

Ratchetwrench

¾”Socket

¾”Boxendwrench

TorqueWrench

Allhardwarewillbefinaltorquedto75ft.lbs.

01/15/18_REV2

PartsList

1.PositiontheBaseCenterTubeandBaseRearTubeasshown.

Connectthetubesusingtheproperhardwar eandlightly tighten.

2.AttachtheLowerHitchBoxWeldmenttotheBaseCenterTubeusingthe

properhardwareandlightlytighten.

3.Attach(2)Feetusingtheproperhardwareandlightly tighten.

4.Ensure

bothfeetandtherearbasetubelieflatonthefloor.Torqueall

hardw areto75ft.lbs.

01/15/18_REV2

BaseAssembly

5.AttachaBaseVerticalLegtoeachsideoftheBaseRearTube.Torqueall

hardw areto75ft.lbs.

01/15/18_REV2

UprightAssembly

LowerAFr am eAssembly

6.AssembletheCouplerBodytoeachRectangularTubewhileonaworkbench

orfloorbeforeattachingtothestandbase.Note:Theendofthetubewiththe

singleholeisattachedtothecoupler.Lightlytightenhardware.

01/15/18_REV2

7.InstalltheShankandHeadAssemblywithHitchBallthatwillbedisplayedon

thestand(Notincluded).Thiswillallowyoutoalignthedisplaystandproperly.

8.Using2people,carefullyplacetheassembledAFrameonthestandand

attachtheCouplertotheHitchBall.

InstallthehardwaretoattachtheRectangularTubingtotheBaseVertical

Legs.Lightlytightenhardware.

01/15/18_REV2

BesurethehitchballisattheproperheighttoallowtheAframetositlevel.

Adjusttheballheightifnecessary.

01/15/18_REV2

AligntheAFramesobothsidesareatthesameangle.Torqueallhardwareto

75ft.lbs.

PlateAssembly

10.Theplatescanbeattached2ways.Forlongerlengthhitchdisplays,

assemblewiththestraightsidetowardsthefrontofthestand.Forshorter

lengthhitchdisplays,assemblewiththeangledsideoftheplatestowardsthe

frontofthestand.Installallhardwareandlightlytighten.

Note: The

hookplatecanbeinstalledoneitherside.

01/15/18_REV2

StraightSide

AngledSide

Frontofstand

UpperAFram e Assemb ly

11.TemporarilyremovethehitchpinfromtheLowerHitchBox,installthe

UpperHitchBoxWeldment,thenreplacethehitchpin.

12.InstalltheShankandHeadAssemblywithHitchBall thatwillbedisplay ed

onthestand(Notincluded)intheUpperHitchBox.Thiswillallowyouto

align

thedisplaystandproperly.

01/15/18_REV2

HitchPin

Repeatstep6toassembletheupperAFrameAssembly.

13.Using2people,carefullyplacetheassembledAFrameonthestandand

attachtheCouplertotheHitchBall.

14.InstallthehardwaretoattachtheRectangularTubingtoPlatesA &B.

Lightlytightenhardware.

Note: Thehookplate

canbeinstalledoneitherside.

BesurethehitchballisattheproperheighttoallowtheAframetositlevel.

Adjusttheballheightifnecessary.

AligntheAFrameasdescribedonPage7,thentightenallhardwareto75ft.

lbs.

01/15/18_REV2

TheStandassemblyisnowcomplete.

Installspringbars,brackets,orswaycontrolsonyourdisplayasdesired.

Husky 33144 User manual

Husky 33144 User manual

Related papers

Other documents