Lightspeed Redcat Access User guide

Lightspeed
Brand
Lightspeed
Model
Redcat Access
Type
User guide

This manual is also suitable for

Lightspeed Redcat Access is a wireless presenter system that allows you to share your presentations, videos, and audio wirelessly. It features a compact design, easy setup, and a range of up to 100 feet. The Redcat Access also includes a built-in microphone and speaker, so you can give presentations without needing additional equipment. Additionally, it has the capability to connect to external audio sources and adjust the volume using the Media Connector.

Lightspeed Redcat Access is a wireless presenter system that allows you to share your presentations, videos, and audio wirelessly. It features a compact design, easy setup, and a range of up to 100 feet. The Redcat Access also includes a built-in microphone and speaker, so you can give presentations without needing additional equipment. Additionally, it has the capability to connect to external audio sources and adjust the volume using the Media Connector.

REDCAT ACCESS PRESENTER SET UP
Attach Camera Mounting Shoe to the RCMB
bracket using the mounting hardware.
If desired, remove the table stand feet from the
Redcat Access.
Remove Camera Mounting Shoe from your camera tripod (not
included). Set up the tripod and adjust the legs so that the tripod is
stable and the Redcat Access, when attached, is approximately 6 - 7”
from the floor.
Insert the bracket/shoe assembly onto the tripod.
Then slide the Redcat Access onto the bracket as
shown.
If not using battery, plug power supply into Redcat access and
wrap the cord through the cable management slots to provide
strain relief. If using battery pack, simply press power button to
power on Redcat Access
Lightspeed Technologies
www.lightspeed-tek.com / 800.732.8999 / 503.684.5538
QS0537US01-2
REDCAT ACCESS PRESENTER SET UP
Earset Mic
Lapel Mic
CHARGE MICROPHONES NIGHTLY
10. Place the Flexmike into the cradle charger. The power button light will glow red and the Mic
status light will glow blue. When Flexmike is fully charged, the power button light on the mic
will change to green.
AUDIO INMICROPHONE AUDIO OUT
POWER
MIN
LINK
MAX MIN MAX MIN MAX
8
Power / Mute
1
3
4
10
USING THE OPTIONAL MEDIA CONNECTOR AS A WIRELESS AUDIO LINK
5. Plug the micro USB end of the power cable into the power adapter. Plug the other end of the
cable into the micro USB port on the back of the Media Connector. Plug the USB1 into a wall
outlet.
6. When powered on, the blue LED will glow.
7. Plug your external audio equipment (for example, laptop), into one of the input jacks on the
back of the Media Connector labeled β€œAudio In” using a 3.5mm patch cable.
8. Adjust volume at the audio source. If necessary, further volume adjustment may be made
using the Audio In volume control on the front of the Media Connector.
9. If no Media Connector is present, you may connect an audio source using a 3.5mm patch cable
to the Audio In jack on the side of the Redcat.
For complete operating instructions go to www.lightspeed-tek.com/RedcatAccess-usermanual
(or scan the 2D barcode below).
REGISTER
AUDIO IN
MIN
MAX
AUDIO
(ALD) OUT
MIN
MAX
ON/OFF
DC INPUT
24V/1.75A
9
1 4
322
1
AUDIO INAUDIO OUT
REGISTER
USB POWER
5V/1.5A
TONE
TREBLE BASS
2
7
5
USING THE FLEXMIKE
1. Remove microphone from charger and place the microphone around your neck. If not
using a lapel or earset, ensure the top of the microphone is at the collarbone. The boom
of the earset should be close to your mouth. The lapel mic should be clipped as high as
possible.
2. When using a lapel or earset microphone, plug the mic jack into the mic jack.
3. Press the power/mute button. The mic status will turn blue, indicating the
microphone is active.
4. Microphone volume may be adjusted at the microphone by using the Up/Down buttons
on the side of the Flexmike. It may also be adjusted by using the Microphone volume
knob on the front of the Media Connector.
2
  • Page 1 1
  • Page 2 2

Lightspeed Redcat Access User guide

Lightspeed
Brand
Lightspeed
Model
Redcat Access
Type
User guide
This manual is also suitable for

Lightspeed Redcat Access is a wireless presenter system that allows you to share your presentations, videos, and audio wirelessly. It features a compact design, easy setup, and a range of up to 100 feet. The Redcat Access also includes a built-in microphone and speaker, so you can give presentations without needing additional equipment. Additionally, it has the capability to connect to external audio sources and adjust the volume using the Media Connector.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents